Rate of swelling of sodium polyacrylate

The kinetics of the swelling of sodium polyacrylate (NaPA), a hydrophilic polymer, was studied gravimetrically, by microscopic observation, and calorimetrically. The swelling process followed first-order kinetics and the rate constant was of the order of 10^?2 s^?1. The gravimetric method, however, was not useful for kinetic studies. The rate constant was depressed by the addition of sodium chloride. The activation energy of the swelling was 46.0 ± 6.2 (kJ mol^?1) and decreased with the increase in sodium chloride concentration. In acid solution, the activation energy was almost the same as that in water. The heat of the swelling was 196 ± 17 J g^?1 and did not vary with the addition of sodium chloride. © 1993 John Wiley & Sons, Inc.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

Ash deposition behavior of upgraded brown coal in pulverized coal combustion boiler

Ash with a low melting point causes slagging and fouling problems in pulverized coal combustion boilers. Ash deposition on heat exchanger tubes reduces the overall heat transfer coefficient due to its low thermal conductivity. The purpose of this study is to evaluate the ash deposition for Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. The UBC stands for Upgraded Brown Coal. The melting temperature of UBC ash is relatively lower than that of bituminous coal ashes. Combustion tests were conducted on blended coal consisting 20 wt.% of UBC and 80 wt.% of bituminous coal. Before actual ash deposition tests, the molten slag fractions in those coal ashes were estimated by means of chemical equilibrium calculations. The calculation results showed the molten slag fraction for UBC ash reached approximately 90% at 1523 K. However, that for blended coal ash decreased to 50%. These calculation results mean that blending UBC with bituminous coal played a role in decreasing the molten slag fraction. This phenomenon occurred because the coal blending led to the formation of alumino-silicates compounds as a solid phase. Next, ash deposition tests were conducted using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at both 1523 K and 1273 K in the boiler to measure the amount of ash deposits. The results showed that the mass of ash deposition for blended coal did not greatly increase, compared with that for bituminous coal alone. Therefore, appropriately blending UBC with bituminous coal enabled the use of UBC without any ash deposition problems in practical boilers.     

Preparation of surfactant-free vinyl polymers by conventional emulsion polymerization using hydrolysable emulsifiers

Emulsion polymerizations of several vinyl monomers, styrene, methyl methacrylate, butyl methacrylate, butyl acrylate, and vinyl acetate, in water using alkali–hydrolysable cationic surfactants with a betaine ester group (1-alkoxycarbonylmethyl)trimethylammonium chlorides, as emulsifiers were carried out and properties of the resulting latices and the polymers recovered by hydrolysis and salting out were investigated. There were little influences of the surfactants and monomers used here on the polymerizations, forming stable and monodisperse latices with a mean diameter of ca. 70 nm and giving a high molecular weight of polymers at high yields. All polymers were precipitated and recovered by adding a small amount of sodium hydroxide into the latex solutions contained little amount of ionic species. Solvent-cast films of the polymers were found to have surfaces as hydrophobic as those for the corresponding pure polymers prepared by bulk polymerization.     

In situ time-resolved X-ray diffraction of tobermorite formation in autoclaved aerated concrete: Influence of silica source reactivity and Al addition

The hydrothermal formation of tobermorite during the processing of autoclaved aerated concrete was investigated by in situ X-ray diffraction (XRD) analysis. High-energy X-rays from a synchrotron radiation source in combination with a newly developed autoclave cell and a photon-counting pixel array detector were used.To investigate the effects of the silica source, reactive quartz from chert and less-reactive quartz from quartz sand were used as starting materials. The effect of Al addition on tobermorite formation was also studied. In all cases, C-S-H, hydroxylellestadite and katoite were clearly observed as intermediates.Acceleration of tobermorite formation by Al addition was clearly observed. However, Al addition did not affect the dissolution rate of quartz. Two pathways, via C-S-H and katoite, were also observed in the Al-containing system. These results suggest that the structure of initially formed C-S-H is important for the subsequent tobermorite formation reactions.     

Limiting flux in microfiltration of colloidal suspensions by focusing on hydrodynamic forces in viscous sublayer

Cross‐flow microfiltration tests were performed on colloidal suspensions under turbulence conditions. By changing the particle diameter, flow rate, and channel height in the membrane housing to measure limiting fluxes, the influence of each parameter on the limiting flux was assessed from the viewpoint of hydrodynamic forces exerted on a particle in the viscous sublayer. In analyzing all the data taken, the particle Reynolds number calculated from the limiting flux is proportional to the 1.5 power of that calculated from the flow rate at the boundary between the viscous sublayer and the intermediate layer. This fact indicates that the limiting flux can be determined in situations where the drag force exerted by the flux is balanced by the lift force in the viscous sublayer. © 2017 American Institute of Chemical Engineers AIChE J, 64: 1760–1765, 2018     

Photocatalytic hydrogen production from water with nonfood hydrocarbons as oxidizing sacrifice agents

To enhance photocatalytic water splitting, various oxidizing sacrifice agents (OSA) have been added to the system in order to scavenge the coproduced O₂, and, thus, to hinder the reverse reactions. In the aim of achieving carbon‐neutral photocatalytic water splitting, nonfood hydrocarbons of castor‐ and jojoba‐oils were evaluated as OSA. Moreover, various surfactants were tested as emulsifiers for W/O binary solution for promoting photocatalytic water splitting rate. Among the OSA used, the castor‐oil was found to be more suitable candidate compared to jojoba‐oil, which was attributed to its smaller carbon chain numbers of mainly 18. Without surfactants, around 20 vol %‐castor‐oil aqueous binary solution with TiO₂/Pt(0.10 wt %) provided the highest water splitting rate of about 30 mL‐H₂/(m²·h). Among tested surfactants, liquid‐detergent was the best due to its optical transparency. 40 vol %‐ or 60 vol %‐castor‐oil emulsion with a drop of liquid‐detergent resulted in a water splitting rate of 125 mL‐H₂/(m²·h), which was four times greater that the aforementioned highest value. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

Simulation of thermophysical flow in axisymmetric nozzle with expansion chamber

Axisymmetric nozzle flows with a free‐jet expansion are simulated considering several substances and several flow conditions, and the thermophysical properties in the nozzle and the free‐jet region are predicted. The present numerical method is based on the preconditioning method developed by Yamamoto and the mathematical models of thermophysical properties of the substances. As numerical examples show, gas flows of carbon dioxide, water, and nitrogen under a subcritical pressure condition are first calculated. Calculated distances to the Mach disk are compared with the experimental results, and also the density distributions are compared among these three substances. Second, carbon dioxide flows while changing the pressure from subcritical to supercritical values are calculated and the effect of pressure on the flow field is investigated. Third, flows of water vapor with and without nonequilibrium condensation are calculated and the effect of condensation on the flow field is investigated. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

Very slow formation of copper sulfide and cobalt sulfide nanoparticles in montmorillonite

Intercalation of semiconductor nanoparticles, copper sulfide or cobalt sulfide, into montmorillonite was carried out by solid–solid reactions of Cu(II)- or Co(II)-montmorillonite with sodium sulfide at room temperature. The intercalation compounds were characterized by X-ray diffraction, thermal analysis, transmission electron microscopy, Raman, UV–visible and photoluminescence spectroscopy. The photoluminescent copper sulfide and cobalt sulfide nanoparticles in the interlayer spaces formed after the sample storage at room temperature for several months.