Harmonic blue light generation in periodically poled bulk near-stoichiometric MgO:LiNbO/sub 3/

A periodically poled structure with 6.95 /spl mu/m period and 10 mm interaction length was fabricated in a 1 mm-thick 1.8 mol% MgO doped near-stoichiometric LiNbO/sub 3/ (MgSLN) by using a multi-pulse poling technique. Blue SHG characteristics of this periodically poled MgSLN were investigated, in comparison with a periodically poled 5 mol% MgO doped congruent LiNbO/sub 3/.     

Coherent FSK transmitter using a negative feedback stabilised semiconductor laser

An electrical negative frequency feedback scheme is applied to a semiconductor laser to improve its direct frequency modulation performance in an FSK transmitter. An error signal caused by imperfect FM response is extracted through heterodyne discrimination detection with a stable master laser and fed back to the FM semiconductor laser.     

12300 ps/nm, 2.4 Gb/s nonregenerative optical fiber transmissionexperiment and effect of transmitter phase noise

A nonregenerative optical transmission experiment with a chromatic dispersion of more than 10000 ps/nm is reported. Externally intensity-modulated 2.4 Gb/s optical signals were transmitted over 710 km of nondispersion-shifted optical fiber using ten Er-doped fiber amplifiers with a total net optical gain of 125 dB. Although the total chromatic dispersion amounted to 12300 ps/nm, the power penalty observed was as small as 0.5 dB, and an error floor was not observed. The effect of transmitter phase noise associated with fiber chromatic dispersion was experimentally investigated     

Glycocalyx‐Like Hydrogel Coatings for Small Diameter Vascular Grafts

Novel biological vascular conduits, such as decellularized tissue engineered vascular grafts (TEVGs) are hindered by high thrombogenicity. To mimic the antithrombogenic surface of native vessels with a continuous glycosaminoglycan layer that is present on endothelial cells (ECs), a hyaluronic acid (HA) modified surface is established, to effectively shield blood platelets from collagen‐triggered activation. Using the amine groups present on 4 mm diameter decellularized TEVGs, a continuous HA hydrogel coating is built via a bifunctional thiol‐reactive cross‐linker, thereby avoiding nonspecific collagen matrix cross‐linking. The HA hydrogel layer recreates a luminal wall, “hiding” exposed collagen from the bloodstream. In vitro blood tests show that adhered platelets, fibrinogen absorption, and fibrin formation on HA‐coated decellularized TEVGs are significantly lower than on uncoated decellularized TEVGs. The HA surface also inhibits macrophage adhesion in vitro. HA‐coated decellularized syngeneic rat aortae (≈1.5 mm diameter), and TEVGs in rat and canine models, respectively, are protected from aggressive thrombus formation, and preserve normal blood flow. Re‐endothelialization is also observed. HA‐coated TEVGs may be an off‐the‐shelf small‐diameter vascular graft with dual benefits: antithrombogenic protection and promotion of endothelium.     

Destruction of volatile organic compounds used in a semiconductorindustry by a capillary tube discharge reactor

Nonthermal plasma technologies offer an innovative approach to the problem of decomposing various volatile organic compounds (VOCs). The authors focused on DC capillary tube discharge plasma reactors to study the decomposition/destruction efficiency for toluene, EGM, trichloroethane and trichloroethylene at 50-2300 ppm levels in dry air. The effects of gas flow rate, VOC concentration and reactor operating conditions on decomposition and analysis of reactant conversion for each VOC were investigated. The results show that VOC destruction efficiency as high as 90% can be achieved, even under a short residence time (3.8 ms) with a destruction energy efficiency of up to 95 g (VOC)/kWh. Laboratory-scale plasma technology was successfully demonstrated for its potential application for VOC control in the semiconductor clean-room environment     

A life-cycle analysis on thin-film CdS/CdTe PV modules

Authors have evaluated the life cycle of a thin-film CdS/CdTe PV module to estimate the energy payback time (EPT) and the life-cycle CO₂ emissions of a residential rooftop PV system using the CdS/CdTe PV modules. The primary energy requirement for producing 1 m² of the CdS/CdTe PV module was similar to a-Si PV module at annual production scale of 100 MW. EPT was calculated at 1.7–1.1 yr, which was much shorter than the lifetime of the PV system and similar to that of a-Si PV modules. The life-cycle CO₂ emissions were also estimated at 14–9 g-C/kWh, which was less than that of electricity generated by utility companies.     

Effect of catch cup geometry on 3D boundary layer flow over the wafer surface in a spin coating

Recently, development of high technology has been required for the formation of thin uniform film in manufacturing processes of semiconductor as the semiconductor instruments become more sophisticated. Spin coating is usually used for spreading photoresist on a wafer surface. However, since rotating speed of the disk is very high in spin coating, the dropped photoresist scarers outward and reattaches on the film surface. A catch cup is set up outside the wafer in spin coating, and scattered photoresist mist is removed from the wafer edge by the exhaust flow generated at the gap between the wafer edge and the catch cup. In the dry process of a spin coating, it is a serious concern that the film thickness increases near the wafer edge in the case of low rotating speed. The purpose of this study is to make clear the effect of the catch cup geometry on the 3D boundary layer flow over the wafer surface and the drying rate of liquid film.     

Decision-making in electrical appliance use in the home

This paper presents the results of a survey as well as an argument from the viewpoint of behavioral economics with the aim of clarifying how consumers make decisions about electrical appliance use in the home. A survey of consumers showed that most have little awareness of the energy efficiency of appliances, the price of the services produced by electrical appliances, or electricity rates. These findings indicate that price does not function as a signal in electricity consumption through electrical appliance use. Rather, we found that consumer decision-making in electricity consumption is dependent on the characteristics of the particular electrical appliances they use. Additionally, we argue that the payment system for home electricity consumption plays an important role in decision-making, causing biases due to aspects of human psychology discussed here in terms of satisficing and heuristics, payment decoupling, and budgeting. We conclude that decision-making about electrical appliance use and electricity consumption in the home is not always rational and is affected both by the particular characteristics of appliances and the payment system for electricity consumption along with human psychology.     

Over 1.3 /spl mu/m CW laser emission from InGaSb quantum-dot vertical-cavity surface-emitting laser on GaAs substrate

An Sb-based quantum-dot vertical-cavity surface-emitting laser (QD-VCSEL) operating in the 1.3 /spl mu/m optical communication waveband is presented. A QD-VCSEL containing high-density InGaSb QDs in the active region is fabricated on GaAs substrate. The density of InGaSb QDs is drastically increased using a new method of an Si atom irradiation technique. A long-wavelength laser emission at 1.34 /spl mu/m is successfully achieved on the InGaSb QD-VCSEL in CW operation at room temperature.     

Phase and amplitude comparison between experiment and calculation of ultrabroad-band pulses generated in a taper fiber

Using a cross-correlation frequency-resolved optical gating apparatus, the phases and amplitudes of ultrabroad-band optical pulses from a taper fiber have been measured for various input pulse peak powers. The measured waveforms have been compared with calculated waveforms using a finite-difference in the frequency domain method, in which no envelope approximations were used and the variation of the taper shape was taken into account. Excellent agreement between the measured and the calculated waveforms was obtained when the additional dispersion of a normal fiber and an objective was considered.