Effects of palm oil fatty acid on curing characteristics,reversion and fatigue life of various natural rubber compounds

The effects of palm oil fatty acid concentration (0, 1, 3, 5, 7 phr) and epoxidation on curing characteristics, reversion and fatigue life of carbon black filled natural rubber compounds have been studied. Three different types of natural rubber, SMR L, ENR 25 and ENR 50 having 0, 25 and 50 mol% of epoxidation and conventional sulphur vulcanization were used. The cure time t₉₀, scorch time t₂, M_HR − M_L (maximum torque − minimum torque) and fatigue life of all rubbers were found to increase with increasing palm oil fatty acid concentration. However, the reversion of all rubbers decreases with increasing palm oil fatty acid concentration. At similar concentrations of palm oil fatty acid, ENR 50 compounds exhibit the shortest scorch and cure times followed by ENR 25 and SMR L compounds. For reversion, SMR L compounds show the lowest value followed by ENR 50 and ENR 25 compounds, whereas for fatigue life, the highest value is obtained with ENR 50 compounds followed by ENR 25 and SMR L compounds. © 1999 Society of Chemical Industry     

Effect of Bromination on Epdm Curing Behavior and its Tensile Properties

Ethylene propylene diene rubber (EPDM) was brominated. The curing behavior and tensile properties of the brominated EPDM (BEPDM) were investigated using a typical sulfur curing formulation. The brominated EPDM was observed to cure with a shorter cure induction time than the unbrominated one. The activation energies (E _a) of curing for EPDM and brominated EPDM were found to be approximately 145 kJ/mol and 58 kJ/mol, respectively. Analysis of curing behavior with individual curatives and stress-strain measurements indicates that these significant improvements could be attributed to the role of bromine as a more efficient crosslinking site, forming C—O—C crosslinks. In addition, the bromine also seems to increase the solubility of sulfur in the rubber, promoting sulfur crosslinks which are apparently not observed with the unbrominated EPDM. Consequently, the BEPDM displayed significantly higher tensile strength than the unbrominated one.     

Comparison of spontaneously released endothelium-derived relaxing factor in cerebral and extracerebral arteries in rabbits

To investigate regional differences in spontaneously released endothelium-derived relaxing factor (EDRF), a bioassay of spontaneously released EDRF was performed on rabbit basilar, ear, common carotid and thoracic arteries using an isometric tension measurement technique and a measurement of cyclic guanosine monophosphate (cGMP) content in the vascular smooth muscle. The amount of spontaneously released EDRF was higher in the basilar artery than in any other arteries examined (p < 0.01). The levels of cGMP were 57.3 +/- 4.4 (n = 7) in basilar, 26.5 +/- 4.3 (n = 6) in ear, 24.5 +/- 2.3 (n = 11) in common carotid, and 30.3 +/- 3.8 pmol/g tissue (n = 8) in thoracic artery with endothelium, while endothelium-denuded arteries showed 24.2 +/- 6.6 (n = 5), 17.5 +/- 5.1 (n = 6), 20.1 +/- 2.9 (n = 7) and 14.4 +/- 2.3 pmol/g tissue (n = 8) in the same order. Haemoglobin (10(-5) M, incubated with the artery for 5 min, significantly reduced the level of cGMP in all vessels with endothelium: 35.3 +/- 4.4 (basilar), 16.0 +/- 2.1 (ear), 14.0 +/- 1.9 (common carotid) and 8.7 +/- 1.2 pmol/g tissue (thoracic artery). Since endothelium-dependent relaxation is associated with a rise in the cGMP content of the smooth muscle cell, the data of cGMP measurement in addition to the bioassay of spontaneously released EDRF in tension measurement suggests that the spontaneous release of EDRF is much greater in the basilar artery than in extracerebral arteries. It is concluded that the intensity of the spontaneously released EDRF is relatively higher in the intracerebral artery than in the extracerebral artery.     

Effectiveness of intra-arterially infused papaverine solutions of various concentrations for the treatment of cerebral vasospasm

We evaluated the effect of intra-arterially infused papaverine solutions of various concentrations on cerebral vasospasm following subarachnoid haemorrhage. A total of 90 vascular territories in 46 patients with symptomatic cerebral vasospasm after subarachnoid haemorrhage were treated with intra-arterial infusions of papaverine. In all patients, papaverine was infused at the top of the internal carotid artery (ICA). Of the 90 vascular territories, 30 vascular territories in 14 patients were treated with an infusion of 0.1-0.2% (weight/volume) papaverine (Group 1), 30 vascular territories in 16 patients were treated with a 0.4% (w/v) papaverine infusion (Group 2), and 30 vascular territories in 16 patients were treated with an infusion of 0.8-2.0% (w/v) papaverine (Group 3). Among the three groups, we compared the vasodilatory effects of papaverine by assessing the angiographical and clinical improvements following the treatment. When 0.4% (w/v) papaverine was infused, 24 vascular territories (80%) were successfully dilated and 7 patients (44%) showed a marked reversal of neurological deficits due to vasospasm. Therefore, 80 mg/20 ml (0.4% (w/v)) papaverine infused over a 10-minute period proved to be a beneficial concentration. Transient focal neurological deficits due to the infusion of papaverine occurred in 1 Group 1 patient (7%), 1 Group 2 patient (6%), and 7 Group 3 patients (44%). Highly concentrated papaverine had a higher risk of temporary deterioration. In conclusion, the papaverine concentration of 0.4% (w/v) infused at the top of the ICA was a safe and adequate concentration for treating cerebral vasospasm.     

Surface modification of polymethyl methacrylate by graft copolymers

Summary Graft copolymers composed of poly(methyl methacrylate) branches and different backbones of poly(fluoroalkyl acrylate(FA)-co-methyl methacrylate(MMA)), poly (hydroxyethyl methacrylate(HEMA)-co-MMA), and poly(FA-co-HEMA) were prepared by macromonomer technique to study their application as a surface modifier for PMMA films. Contact angle of water droplet on PMMA film specimens containing various amounts of these graft copolymers cast on glass slides from THF solution was found to change considerably with the graft copolymer concentration, depending on their backbone component. And there was considerable difference in contact angle between air and glass side of the film surfaces. These results were considered in terms of the surface accumulation of graft copolymers during the solvent evaporation.     

Synthesis and application of fluorine containing graftcopolymers

Summary Well-defined graftcopolymers were prepared by radical copolymerization of methyl methacrylate macromonomer with perfluoroalkyl acrylate. Contact angle of the solvent cast films of poly(methyl methacrylate) containing various amount of the graftcopolymer was measured against water droplet. Addition of 0.2 wt% of the graftcopolymer was sufficient to improve the polymer films to water repellent surfaces, while 10 wt% was necessary to modify the polymer surfaces to the same level of water repellency.     

Screening of dairy yeast strains for probiotic applications

To evaluate the potential of yeasts of dairy origin as probiotics, we tested 8 species including Candida humilis, Debaryomyces hansenii, Debaryomyces occidentalis, Kluyveromyces lactis, Kluyveromyces lodderae, Kluyveromyces marxianus, Saccharomyces cerevisiae, and Yarrowia lipolytica, isolated from commercial blue cheese and kefir. Strains were randomly selected from each species and tested for their ability to adhere to human enterocyte-like Caco-2 cells in culture. Among the 8 species, K. lactis showed higher adhesive ability than K. marxianus, K. lodderae, and D. hansenii. The other 4 species were poorly adhesive. All species other than K. marxianus and C. humilis were resistant to acidic conditions. In the presence of bile acid, growth inhibition was undetectable when incubation was carried out at 27 degrees C; however, it was evident for C. humilis and a strain of D. occidentalis when incubated at 37 degrees C. Moreover, the influence of proteinase treatment of living cells of K. lactis and K. lodderae on their adhesion to Caco-2 cells was evaluated. Although a slight reduction was recognized when K. lactis was treated with proteinase K, the influence of intestinal protease treatments of pepsin followed by trypsin was negligible. These results indicated that a proteinaceous factor was unlikely to be involved in adhesion of K. lactis and K. lodderae to Caco-2 cells. No stimulation of IL-8 synthesis by Caco-2 cells was recognized in the presence of K. lactis. In conclusion, K. lactis was the most attractive to continue study for use as probiotic microorganisms.     

Zero-birefringence polymer by the anisotropic molecule dope method

We propose using the anisotropic molecule dope method for synthesizing a zero-birefringence polymer that showed no orientational birefringence at any orientation degree of polymer chains. In this method a rodlike molecule with polarizability anisotropy was chosen to compensate orientational birefringence. The zero-birefringence polymer was synthesized by doping of 3-wt.% trans-stilbene as an anisotropic molecule into poly(methyl methacrylate). The zero-birefringence at the 590-nm wavelength in the drawn film and the injection-molded plate made from the zero-birefringence polymer was confirmed by the rotating parallel nicols method. Furthermore, high transparency (37.2 dB/km) of the zero-birefringence polymer at the 633-nm wavelength was confirmed by the light-scattering measurement.