Evaluation of passive microwave snow water equivalent algorithms in the depth hoar-dominated snowpack of the Kuparuk River Watershed, Alaska, USA

This research investigates the utility of passive microwave remote sensing instruments to accurately determine snow water equivalent (SWE) over large spatial extents. Three existing Special Sensor Microwave Imager (SSM/I) snow water equivalent algorithms produced by Chang, Tait and Goodison were evaluated for their ability to determine snow water equivalent in a snowpack containing substantial depth hoar, large faceted snow crystals. The Kuparuk River Watershed (8140 km²) test site on the North Slope of Alaska was chosen for its snowpack containing a think depth hoar layer and long history of ground truth data. A new regional snow water equivalent algorithm was developed to determine if it could produce better results than the existing algorithms in an area known to contain significant depth hoar. The four algorithms were tested to see how well they could determine snow water equivalent: (1) on a per pixel basis, (2) across swath-averaged spatial bands of approximately 850 km², and (3) on a watershed scale. The algorithms were evaluated to see if they captured the annual spatial distribution in snow water equivalent over the watershed. Results show that the algorithms developed by Chang and from this research are generally within 3 cm of the spatially averaged snow water equivalents over the entire watershed. The algorithms produced by Chang, Tait, and in this research were able to predict the basin-wide ground measured snow water equivalent value within a percent error range from −32.4% to 24.4% in the years with a typical snowpack. None of the algorithms produce accurate results on a pixel-by-pixel scale, with errors ranging from −26% to 308%.     

Neural-Net Analysis of the Plasticity of ÉP-450 Ferrite–Martensite Steel with Different Alloying Element Concentrations

The results of a computational experiment with a neural-net model simulating the effect of the chemical composition on the plastic properties of ÉP-450 steel are presented. It is shown that computer-aided development of reactor steel with prescribed properties is, in principle, possible.     

SVBR-75/100 Multipurpose Modular Low-Power Fast Reactor with Lead–Bismuth Coolant

The results of development work on the SVBR-75/100 modular fast reactor cooled by lead–bismuth coolant are presented. The design is based on the experience gained operating reactors in nuclear-powered submarines. The SVBR-75/100 reactor is inherently safe because of its low power, the chemical inertness and high boiling point of the lead–bismuth coolant, and the integrated basin-type arrangement of the first-loop equipment. This eliminates the conflict between the safety and economic requirements that is characteristic of conventional-type reactors. The lower power makes it possible to build the reactor in a factory and deliver the reactor using any form of transportation to the nuclear power plant site. All safety systems operate passively. Most of these systems are used as normal-operating systems. This creates conditions for multipurpose applications of such reactor modules in developed and developing countries.     

Mg AZ80/SiC composite bars fabricated by infiltration of porous ceramic preforms

Semi-industrial samples of Mg AZ80/SiC/50p composites (machined bars with o.d.=80 mm and length=150 mm, having a maximum 2 vol pct of retained porosity) were successfully fabricated by pressureless, low-pressure (under overpressure of about 0.3 MPa) and moderate-pressure (under overpressure of about 0.8 MPa) infiltration. Pressureless infiltration was completed in 24 hours under the flowing atmosphere of nitrogen, whereas the moderate and low-pressure infiltrations were performed under a static atmosphere of pressurized nitrogen for 7 and 0.5 hours, respectively. The composite samples obtained by all applied infiltration paths posessed a homogeneous microstructure and superior mechanical properties as compared to the nonreinforced matrix. Due to the improved productivity of composite fabrication in comparison with the other two infiltration paths investigated in this work, the moderate-pressure infiltration process was recognized as the most competitive.     

Second-order stresses and strains in heterogeneous steels: Self-consistent modeling and X-ray diffraction analysis

Theoretical and experimetal methods have been developed to characterize the effect of mechanical loading on the mesoscopic and macroscopic mechanical state of polycrystalline materials. Ferritic and austenitic single-phase materials were first analyzed, then phase interaction was studied in a multiductile phase material (austeno-ferritic duplex steel) and a natural reinforced composite (pearlitic steel). The theoretical method is based on the self-consistent approach in which elastic and plastic characteristics of the phases have been applied through the micromechanical behavior of single-crystal-using slip systems and microscopic hardening. The effects of a crystallographic texture and phase interaction during loading and after unloading were studied. The elastic and plastic anisotropy of the grains having the same crystallographic orientation were assessed by diffraction strain analysis. The simulation was compared with the experiments performed using the X-ray diffraction technique. In the considered duplex and pearlitic steels, it was observed that the ferrite stress state is much lower than the austenite and cementite ones. The results of diffraction strain distribution have showed the pertinence of the models and give valuable information, for example, for the yield stress and the hardening parameters of each phase in a two-phase material.     

Effect of broaching on high-temperature fatigue behavior in notched specimens of INCONEL 718

Notches were machined in specimens of INCONEL 718 by a broaching process, where differing broaching runs led to differing extents of subsurface deformation and surface roughness. Fatigue tests were carried out at 600 °C with a trapezoidal loading waveform at 0.25 Hz. The broaching process that led to the more severe subsurface deformation (but lower surface roughness) showed the worst fatigue performance. Analysis of total strain amplitude in the notch root with the aid of an elastoplastic finite-element (FE) model showed that the work hardening related to the subsurface deformation caused by the different broaching can account for the difference in fatigue lives. Differences in initiation and growth behavior were seen for the two broached finishes as well as for broached and subsequently polished samples. These differences are discussed in terms of a change in crack growth initiation and growth mechanisms due to the presence of the work-hardened layer.     

Cyclic oxidation response of multiphase niobium-based alloys

Cyclic oxidation tests were performed on multiphase Nb-based alloys containing silicide, Laves, and Nb solid solution phases. In particular, the oxidation resistance of six alloys with various compositions (Nb, Ti, Hf, Cr, Ge, and Si) and microstructures was characterized by thermal cycling from ambient temperature to a peak temperature that ranges from 900 °C to 1400 °C. Weight change data were obtained and the corresponding spalled oxides were collected and identified by X-ray diffraction. The results indicated that Nb-based alloys formed a mixture of CrNbO₄, Nb₂O₅, and Nb₂O₅ · TiO₂, with possibly small amounts of SiO₂ or GeO₂. The oxidation resistance was improved when CrNbO₄ formed instead of Nb₂O₅ and Nb₂O₅ · TiO₂. These results were used to assess the influence of microstructure and composition on the oxidation resistance of multiphase Nb-based alloys.     

Quantifying the benefits of enhanced filter selectivity

Today's mobile communications market is very competitive, with wireless service providers making every effort to improve the performance of their network to retain subscribers. Coupled with the proliferation of radio-frequency signals in the environment due to the growth of all forms of wireless communication, this leads to a very challenging task - namely, to provide ubiquitous high-quality service in spite of ever-increasing interference levels. One of the tools at the disposal of the network operator to provide such service is a cryogenically cooled receiver front end for base stations, wherein each receive path consists of a high-temperature superconducting (HTS) bandpass filter followed by a cryogenically cooled low-noise amplifier. There are two primary benefits achieved by the use of this front end. The first is improved receiver sensitivity through the reduction of electrical noise generated by the front end itself. The second is the significant reduction in the effects of out-of-band interference through the highly selective filtering made possible by the use of HTS materials. While this paper addresses both receiver-sensitivity and filter-selectivity benefits, the focus is on improved out-of-band interference rejection through enhanced filter selectivity.     

On one boundary-value problem for the Laplace equation

We have derived a Fredholm-type equation of the second kind for a directional derivative problem arising in the stationary theory of heat conduction. One result of Ya. B. Lopatinskii has been refined. __________ Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 80, No. 2, pp. 197–200, March–April, 2007.