Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Continuous phase quadrature phase shift keyed signaling techniquewith coding

A continuous phase quadrature phase shift keyed (CPQPSK) modulation technique is presented. This method utilizes a conventional QPSK modulator and a phase trajectory converter to approximate M=4, h=1/4 continuous phase signal and allows low cost, low complexity, and high rate (>1 Gbit/s) CPM modem implementation for bandwidth efficient transmission through nonlinear satellite channels. Using a communications analysis computer program it has been found that CPQPSK has 99 percent out-of-band power of 0.8R (MSK has 99 percent out-of-band power of 1.2 R where R is defined as bit rate), continuous phase trajectories, and nearly constant envelope amplitude. Simulation of realistic hardware designs indicate that the CPQPSK will require an Eb/No of 14 dB to achieve a bit error rate (BER) of 10^-6. Forward error correcting techniques using block codes with an overhead of 10 percent indicate that the Eb/No requirements can be reduced to 11.2 dB for 10^-6 BER     

Synthesis and characterisation of copolyesters from poly(ethylene terephthalate) and poly(hexamethylene terephthalate)

Copolyesters containing poly(ethylene terephthalate) and poly(hexamethylene terephthalate) (PHT) were prepared by a melt condensation reaction. The copolymers were characterised by infrared spectroscopy and intrinsic viscosity measurements. The density of the copolyesters decreased with increasing percentage of PHT segments in the backbone. Glass transition temperatures (T_g). melting points (T_m) and crystallisation temperatures (T_c) were determined by differential scanning calorimetry. An increase in the percentage of PHT resulted in decrease in T_g, T_m and T_c. The as-prepared copolyesters were crystalline in nature and no exotherm indicative of cold crystallisation was observed. The relative thermal stability of the polymers was evaluated by dynamic thermogravimetry in a nitrogen atmosphere. An increase in percentage of PHT resulted in a decrease in initial decomposition temperature. The rate of crystallisation of the copolymers was studied by small angle light scattering. An increase in percentage of PHT resulted in an increase in the rate of crystallisation.     

Control of free-radical emulsion polymerization of methyl methacrylate by oxygen injection. II. Experimental study

Oxygen injection has been proposed and experimentally demonstrated as an effective control measure for limiting the rate of heat release and altering the rate of polymerization in emulsion processes. A detailed mathematical model has been previously developed to describe the system behavior with and without oxygen injection. A simple lab scale apparatus was constructed and run extensively. Only trace quantities of oxygen are needed to inhibit the reaction completely. The facile response makes this method attractive for fast temperature control. However, because of the rapid penetration of dissolved oxygen into the polymer particles, growing radical chains are terminated prematurely, lowering product molecular weights. To minimize this detrimental effect, pulsed oxygen control is used and extensive experimental work was performed to determine the effects of controller set points on molecular weight. Moderate oxygen flows and moderate set point temperatures are found to give the optimal response without significant lowering of the final molecular weight. Injected quantities agree well with the order-of-magnitude sparging calculations needed to completely stop initiation. However, complete agreement between model simulations and experimental results was not reached due to an unmeasured loss of monomer from the reactor. Chain transfer to monomer is found to be important in modeling the polymer molecular weight. It has, however, a negligible effect on the reaction rate.     

Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices