Fill factor losses in ZnO/CdS/CuGaSe2 single-crystal solar cells

Current–voltage characteristics of ZnO/CdS/CuGaSe₂ single-crystal solar cells with solar conversion efficiency values of η=3.5%, 6.0%, 6.7% and 9.7% were analyzed using the single diode equation. The effect of each of the achieved parameters on the fill factor was calculated. The calculations revealed that the fill factor reduction due to the series resistance remained below Δff=4.4% under illumination, while this effect would have been much higher if the illumination had not reduced the series resistance markedly. The calculation furthermore revealed that the fill factor reduction due to the shunt resistance remained below Δff=3.6% under illumination. This effect would have been negligible if the illumination had not also reduced the shunt resistance in all studied cells. The increase of the saturation current density under illumination has brought about considerably high fill factor losses (at least Δff=8.3%) in all studied cells. Already the dark saturation current density and the diode ideality factor in such cells have been found to be much higher than the ones in the cells based on CuInSe₂. This seems to be the most substantial restriction to the fill factor, and thus to the performance, of solar cells based on CuGaSe₂. An explanation for this different behavior seems to lie in the different band structures of these cells.     

Influence of lactic acid bacteria on survival of Escherichia coli O157:H7 in inoculated Minas cheese during storage at 8.5 degrees C

Minas cheese is a typical Brazilian fresh cheese, manufactured by addition of rennin and CaCl2 to milk, followed by draining the curd. The intrinsic characteristics of this product make it favorable for growth of pathogens, including Escherichia coli O157:H7. The influence of the addition of a commercial mesophilic type O lactic culture to this product on the growth of this pathogen during storage at 8.5 degrees C was evaluated. Eight different formulations of Minas cheese were manufactured using raw or pasteurized milk and with or without salt and lactic culture. Individual portions of each formulation were transferred to sterile plastic bags and inoculated with E. coli O157:H7 to yield ca. 10(3) or 10(6) CFU/g. After blending by hand massaging the bags, samples were stored at 8.5 degrees C for up to 14 days. E. coli O157:H7 was counted after 1, 2, 7, and 14 days of storage using 3M Petrifilm Test Kit-HEC. Counts in samples without added lactic culture showed a 2-log increase in the first 24 h and remained constant during the following 14 days. Counts in samples with added lactic culture showed a 0.5-log increase in the first 24 h, followed by a decrease. These variations were statistically significant (P < 0.05). No significant variations (P > 0.05) were obtained for cheese samples manufactured with pasteurized or raw milk, with or without salt. Results indicate that the addition of type O lactic culture may be an additional safeguard to well-established good manufacturing practices and hazard analysis and critical control point programs in the control of growth of E. coli O157:H7 in Minas cheese.     

Spectrophotormetric Determination of Quinolinium Acid Esters with 2, 4-Dinitrophenylhydrazine

Carbonyl compound. react with 2, 4-dinitrophtnylhydrazin. to form the corresponding hydrsiones. These hydrazones in the prrsence of lN NaOH give a reddish brown color which can be utilized for colorimatric analysis. This method is used for the spectrophoto-metric determination of quinolinium-6-carboxy-l-metliyl- iodide. Furthermota 2. 4-dinitrophenylhydrazine is utilized to kinetic measurements of the rate of hydrolysie of the quinolinium acid esters.     

Backstepping-based cooperative and adaptive tracking control design for a group of underactuated AUVs in horizontal plan

In this paper, we investigate new implementable cooperative adaptive backstepping controllers for a group of underactuated autonomous vehicles that are communicating with their local neighbours to track a time-varying virtual leader of which the relative position may only be available to a portion of the team members. At the kinematic cooperative control level of the autonomous underwater vehicle, the virtual cooperative controller is basically designed on a proportional and derivative consensus algorithm presented in Ren (2010) Ren, W. (2010). Consensus tracking under directed interaction topologies: Algorithms and experiments. IEEE Transactions on Control Systems Technology, 18, 230–237.[Crossref], [Web of Science ®] , [Google Scholar], which involves velocity information from local neighbours. In this paper, we propose a new design algorithm based on singular perturbation theory that precludes the use of the neighbours’ velocity information in the cooperative design. At the dynamic cooperative control level, calculation of the partial derivatives of some stabilising functions which in turn will contain velocity information from the local neighbours is required. To facilitate the implementation of the cooperative controllers, we propose a command filter approach technique to avoid analytic differentiation of the virtual cooperative control laws. We show how Lyapunov-based techniques and graph theory can be combined together to yield a robust cooperative controller where the uncertain dynamics of the cooperating vehicles and the constraints on the communication topology which contains a directed spanning tree are explicitly taken into account. Simulation results with a dynamic model of underactuated autonomous underwater vehicles moving on the horizontal plane are presented and discussed.     

Studies of electrical and mechanical properties of semiconductive poly(vinyl chloride) compositions

A sample of poly(vinyl chloride) (PVC) and a polar plasticizer consisting of dioctylphthalate (DOP) and triisopropylphenylphosphate (TIPPP) was prepared and found to possess some electrical conductivity. Different samples of PVC compositions were formulated from the PVC-DOP-TIPPP system and also variable proportions of the conductive materials polyaniline or the Ni salt of ethylene glycol bisadipate ester. Dibutyltindilaurate as a heat stabilizer, titanium oxide as a filler, and sandorin red 20 pigment were added. The effect of the structure of polyaniline and Ni adipate ester on the electrical and mechanical properties of the PVC–DOP–TIPPP system was studied to obtain a semiconductive plasticized PVC with good mechanical properties. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 685–693, 1998     

One-pot lithium bromide-catalyzed reaction of polyoxyethylene diglycidyl ether with carbon disulfide: synthesis of new polyoxyethylene epoxyoxathiolane-2-thione

A simple and highly efficient regio- and chemio-specific synthesis of polyoxyethylene epoxyoxathiolan-2-thione was realized from a one-pot reaction of polyoxyethylene diglycidyl ether and carbon disulfide using lithium bromide as a catalyst. The unsymmetrical obtained products were fully characterized by ¹H, ¹³C NMR and high-resolution mass spectra data.     

The voltage mirror–current mirror pair as a universal element

The voltage mirror–current mirror (VM–CM) pair is shown to be a universal active element. It provides two alternative realizations for the nullor. The VM–CM pair is also capable of realizing the op amp and all the four types of the current conveyors namely CCII?, CCII+, ICCII? and ICCII+ as special cases. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of first‐ and second‐generation polyamide pyridylimine nickel dihalide metallodendrimers and their uses as catalysts for ethylene polymerization

First‐ and second‐generation pyridylimine‐terminated dendrimeric ligands were prepared by the reaction of the corresponding amine‐terminated aromatic polyamide dendrimers with 2‐acetylpyridine. The pyridylimine terminal groups were used as bidentate N,N ligands of nickel halide to prepare the corresponding first‐generation and second‐generation nickel dihalide metallodendrimers C1 and C2 , respectively. The synthesized dendrimers and metallodendrimers were characterized by elemental and spectral analyses. C1 and C2 were evaluated as catalyst precursors for ethylene oligomerization after being activated with methylaluminoxane (MAO) and diethylaluminum chloride (Et₂AlCl) under 1 atm and 5 atm pressure of ethylene. In both cases, the use of 1 atm or 5 atm pressure of ethylene and a 1500:1 Al:Ni molar ratio for C1 and C2 resulted in high catalytic activities toward ethylene polymerization. Upon activation with MAO and Et₂AlCl, C1 exhibited promising activities toward ethylene polymerization and produced linear chain structures that were associated with high density polyethylene. In contrast, C2 produced a polymer with the branching nature of low density polyethylene under similar conditions. © 2014 Society of Chemical Industry     

Synthesis of a novolac‐based 3‐aminopropylsiloxane resin and its application for the removal of Cu2+, Cr3+, and Ni2+ from electroplating wastewater

Novolac resin was modified with 3‐aminopropyltrimthoxysilane to obtain phenol‐formaldehyde‐aminopropylsiloxane resin (PF‐APS). Fourier transformation infra‐red spectra, thermogravimetric analysis, elemental analysis, and pH‐metric titration were used to characterize PF‐APS. Its chemical formula was suggested to be C₁₄H_12.49N_0.1O₂Si_0.1. The resin shows high experimental metal ions uptake capacity within short time of equilibration. The metal capacity was determined by atomic absorption spectrometry to be 0.787 mEq Cu/g. Maximum separation efficiencies of Cu²⁺, Cr³⁺, and Ni²⁺ from aqueous solutions on PF‐APS were at pH 8.0 and time of stirring 60 min; 94.0%, 90.8%, 83.2%, respectively. No significant interference from the background ions Na⁺, Cl^?, and was observed on the separation process. The heavy metal ions were eluted using 0.01 mol L^?1 EDTA at 65°C releasing >94% of the separated metal ions. The method of separation was applied successfully to remove the heavy metal ions Cu²⁺, Cr³⁺, and Ni²⁺ from electroplating wastewater from Dekirnis, Dakahlia Governorate, Egypt. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40993.