Alternative technologies for biotechnological fuel ethanol manufacturing

The challenges of implementing biorefineries on a global scale include socioeconomic, financial, and technological constraints. In particular, the development of biorefineries is tightly linked to the continued availability of fermentation raw materials. These constraints can be relaxed by the use of diverse raw materials, while advances that confer higher flexibility would enable biotechnological plant managers to swiftly react to volatile markets. In conventional processes, Saccharomyces cerevisiae grows on a relatively limited range of substrates, and produces only a single product—ethanol. Given the observed maturity of the S. cerevisiae fermentation technology, alternatives to baker's yeast may be needed to tip the economic balance in favour of biotechnological ethanol. These alternative fermentation technologies may allow a greater diversity of substrates to be used to produce an individually tailored mix of ethanol and other chemicals. Copyright © 2007 Society of Chemical Industry     

Evaluation for the curing characteristics of phenolic molding compounds by rockwell hardness test at an elevated temperature

Rockwell hardness measurement at an elevated temperature has been proposed as an evaluation method for the curing characteristics of thermosetting molding compounds. This method is convenient and has a high accuracy over a wide range of curing, Using a cone indenter, the following advantages are brought about: a good correspondence with acetone extraction test, in showing the degree of cure of the internal part of a molding rather than that of the skin layer, and a higher sensitivity in measuring higher degrees of cure. On examining curing behavior of commercial phenolic molding compounds by this method, an inflection point was observed on a plot of the hardness vs log curing time. This critical point has been called “the minimum cure time”, beyond which the molding exhibits good physical properties.     

Pyrolysis–molecular weight chromatography–vapor-phase infrared spectrophotometry: An on-line system for analysis of polymers. IV. Influence of cis/trans ratio on the thermal degradation of 1,4-polybutadienes

The influence of the cis/trans ratio of 1,4-polybutadienes on the volatile products formed during temperature-programmed thermal degradation to 15% weight loss has been investigated using a mass chromatograph (a gas chromatograph which directly provides mass numbers of resolved components of a mixture) and an “on the fly” vapor-phase infrared spectrophotometer. In order of amounts, major volatile products were 4-vinyl-1-cyclohexene (dimer), 1,3-butadiene (monomer), cyclopentene, and 1,3-cyclohexadiene. With increasing trans content, the relative quantities of 4-vinyl-1-cyclohexene decreased strongly, cyclopentene increased strongly, 1,3-butadiene decreased moderately, and 1,3-cyclohexadiene increased moderately. For a high-trans polybutadiene, increasing the heating rate produced relatively more monomer and dimer but less cyclopentene. Mass chromatograms from 1,4-polybutadienes which had been heated to 15% weight loss in their prehistory were similar to those obtained from 1,2-polybutadiene, indicating that 1,4-polybutadiene undergoes isomerization prior to degradation. Mechanisms for the formation of the main volatile products of decomposition are discussed.     

Mechanisms of CO2 separation by microporous crystals estimated by computational chemistry

The diffusion and adsorption of CO₂ inside the pores of Li, Na, and K ion-exchanged X-type zeolites were simulated by molecular dynamics and Monte Carlo calculations. Carbon dioxide diffused inside the zeolites pores while it was colliding with pore walls. Then it stayed in a super cage of zeolites. Inside the pore of Li ⁺ ion-exchanged X-type zeolite (Li-X), the electrostatic potential term was −570 kcal/mol, this value was considerably smaller than those of CO₂ inside the pores of Na-X and K-X. On the other hand, from Monte Carlo calculations, CO₂ was found to strongly absorb near the 3B site for Li ⁺ ions. When CO₂ passed through the pores of alkali ion-exchanged X-type zeolites, the interaction between the CO₂ molecule and the 3B site for Li cation was fairly large.     

Structure and viscoelastic properties of epoxy resins prepared from four-nuclei novolacs

The relation between the structure and the viscoelastic properties of seven kinds of epoxy resins was studied. Seven tetraglycidylethers were synthesized from four-nuclei novolacs in which the positions of methylene linkage or number of kind of substituents were different. These epoxy compounds were cured with diaminodiphenylmethane as a hardener. From the viscoelastic properties of the fully cured resins with the hardener, characteristic properties such as glass transition temperature (T_g), average molecular weight between crosslinking points (M̄_c), and front factor (ϕ) were obtained. It was concluded that higher linearity in the main chain of epoxy resins gave a cured resin with a higher T_g, a smaller M̄_c, and a larger ϕ.     

Preparation of Aragonite Whiskers

A simple synthetic method for preparing aragonite whiskers has been developed. A suspension of CaCl₂-MgCl₂-Mg(OH)₂ with pH ∼9 has been prepared by adding Ca(OH)₂ to MgCl₂ aqueous solution. CaCO₃ whiskers (aragonite phase) have been prepared easily by blowing CO₂-containing gas into the suspension. The whiskers have high aspect ratios ranging from 20 to 80 with diameters of 0.5–1 μm .     

Novel synthesis of microcrystalline titanium(IV) oxide having high thermal stability and ultra-high photocatalytic activity: thermal decomposition of titanium(IV) alkoxide in organic solvents

Thermal decomposition of titanium(IV) tetra-tert-butoxide (TTB) in inert organic solvents at 573 K yielded microcrystalline anatase (titanium(IV) oxide, TiO₂) powders with a crystallite size of ca. 9 nm and a surface area of <100 m² g^-1. Primary and secondary alkoxides of titanium(IV), however, were not decomposed under similar conditions, indicating that the thermal stability of C-O bonds in the alkoxides was a decisive factor for their decomposition. The TiO₂ prepared from TTB by this manner was thermally stable upon calcination in air and retained high surface area of ca. 100 m² g^-1 even after calcination at 823 K. The as-prepared TiO₂ powders, without calcination, exhibited much higher rate of carbon dioxide formation than any other active photocatalysts such as Degussa P-25 and Ishihara ST-01 in the photocatalytic mineralization of acetic acid in aerated aqueous solutions. The higher activity of the present TiO₂ photocatalysts is attributed to both high crystallinity and large surface of the present product. The calcination of the as-prepared TiO₂ in air reduced the photocatalytic activity, but it was still higher than the other commercially available TiO₂'s. This revised version was published online in July 2006 with corrections to the Cover Date.     

Studies on the biaxial stretching of polypropylene film. XI. Type II orientation during [2-2FI]-type stretching and its change by subsequent thermal contraction

In order to study the deformation mechanism of type II stretching, the change in orientation during the restretching and subsequent thermal contraction was investigated by x-ray diffraction method. When a uniaxially oriented film is restretched, the lamellae which are stacked in the stretching direction by the stretching rotate as a whole toward the restretching axis. They rotate backward nearly reversibly during the thermal contraction, unless the restretching exceeds a balancing state, where the orientation in the film plane are equal in all directions. However, when the restretching degree is so high and the film orientation exceeds the balancing state, the lamellar rotation is accompanied by a complex phenomenon. It is considered from the wide-angle and small-angle x-ray diffraction patterns that the lamellar surface becomes indented because of slippage between microfibrils composing the lamellae, and the microfibrils themselves bend at the boundary between the amorphous and crystalline regions within which the tilting of c-axis also occurs. Upon contracting of the film; these changes recover, but even in the last stage of contraction the orientation approaches the symmetrical biaxial orientation but not the uniaxial orientation from which the biaxial orientation is started. These orientation and disorientation behaviors are not affected basically by a slight change in the restretching temperature and the degree of stretching.     

Some Notes on Stability Problems of Probabilistic Automata

Abstract

The behavior of a probabilistic automaton is essentially characterized by products of matrices selected from a given finite set of stochastic matrices. It is of interest to know under what conditions these matrix products are stable against perturbations of the entries in the matrices.