Studies on Isolation and Characterization of Starch from Rajgeera Grains (Amaranthus paniculatus Lin.)

Isolation and some of the important physicochemical properties of starch from rajgeera grains have been investigated. The yield of starch was about 61.2%, on whole grain basis. The results on physicochemical properties revealed that it exhibited moderate swelling and higher solubility (55.5%) in water, as compared to other millet starches. An extensive solubility in dimethylsulphoxid (72.5%) of the starch indicated easy penetration of solvent in a granular matrix, may be due to labile and heterogenous bonding forces within the granules. Brabender viscoamylographic data on pasting characteristics revealed that it yielded low viscosity (448 B. U.) at concentration of 10% (w/v) and showed very little tendency to retrograde during cooling of the starch paste. The amylopectin content was 88.5% indicating the starch of rajgeera is probably waxy in nature. Amylolytic digestibility of native and gelatinized starch of rajgeera by human salivary α-amylase and glucoamylase was investigated.     

Tetraphenylthiophene–thiazole-based π-conjugated polyazomethines: synthesis,characterization and gas sensing application

Polymer Bulletin - 2,5-Bis(4-(2-aminothiazole) phenyl)-3 and 4-diphenyltetraphenyl thiophene (TPTPThDA) are fine processed in three steps. A series of polyazomethines containing...     

Extraction of iridium(III) by ion-pair formation with 2-octylaminopyridine in weak organic acid media

To extract iridium(III), various physicochemical parameters were studied. 2-Octylaminopyridine was used for the extraction of iridium(III) from acetate medium at 8.5 pH. Quantitative extraction of iridium(III) was achieved via ion-pair formation of cation [2-OAPH⁺] and anion [Ir(CH₃COO)₄]^?. The stripping of iridium(III)-laden organic phase was carried out 2 M HCl (3 × 10 mL) . The stoichiometry of the extracted ion–pair complex was found to be 1:4:1 (metal: acetate: extractant). The extracted species [2-OAPH⁺. Ir(CH₃COO)₄^?] is assumed to be an ion association product of [Ir(CH₃COO)₄] ^? and [2-OAPH]⁺. The proposed method was successfully used in the separation of iridium(III) from binary and ternary mixtures. Analysis of various alloy samples was also carried out.     

Corrosion protective bi‐layered composites of polyaniline and poly(o‐anisidine) on low carbon steel

Bi‐layered composites of polyaniline (PANI) and poly(o‐anisidine) (POA) were investigated for corrosion protection of low carbon steel (LCS). In this work, homopolymers and bi‐layers of PANI and POA were electropolymerized on LCS from an aqueous salicylate solution by using cyclic voltammetry. These coatings were characterized by cyclic voltammetry, Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). Corrosion tests were carried out in aqueous 3% NaCl solution for LCS coated with PANI, POA, bi‐layered POA/PANI (POA on top of the PANI) or PANI/POA (PANI on top of the POA) composites using open circuit potential (OCP) measurements, potentiodynamic polarization technique, and electrochemical impedance spectroscopy (EIS). The single layer of PANI and POA protected the LCS in 3% NaCl for 8 and 16 h, respectively. The bi‐layered composite coatings provide effective protection to LCS for a longer time than a single layered PANI or POA coating. However, the corrosion protection offered to LCS depends on the deposition order of polymer layers in the composite. The PANI/POA composite provides better protection to LCS against corrosion than POA/PANI coating. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of Fe2O3 nanoparticles for nitrogen dioxide gas sensing applications

Iron (III) oxide, Fe₂O₃, nanoparticles of approximately 40 nm diameter were synthesized by sol–gel method and their nitrogen dioxide adsorption and desorption kinetics were investigated by custom fabricated gas sensor unit. The morphology and crystal structure of Fe₂O₃ nanoparticles were studied by scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) respectively. The roughness of film surface was investigated by atomic force microscopy (AFM). Relative sensitivity of Fe₂O₃ nanoparticles for NO₂ sensor was determined by electrical resistance measurements. Our reproducible experimental results show that Fe₂O₃ nanoparticles have a great potential for nitrogen dioxide sensing applications operating at a temperature of 200 °C.     

Eight mole percent yttria stabilized zirconia powders by organic precursor route

An organic precursor-mixing route has been developed for preparation of 8 mol% yttria stabilized zirconia (8YSZ) ceramics. Polymeric salt of succinic acid with yttrium and zirconium has been prepared separately by treating sodium succinate with yttrium chloride and zirconyl chloride followed by washing with water and drying at 120 °C. Thorough mixing of the two salts in stoichiometric proportions by planetary ball milling followed by calcination at 850 °C resulted in a precursor powder containing nanocrystalline (∼40 nm) monoclinic zirconia, tetragonal YSZ, cubic YSZ and yttria. Compacts prepared after deagglomeration of powder by planetary ball milling produce 8YSZ ceramics having density 99.3% TD on sintering at 1550 °C for 2 h.     

An experimental investigation of the optimum geometry for the cold end orifice of a vortex tube

A vortex tube is a simple mechanical device, which splits a compressed gas stream into a cold and hot stream without any chemical reactions or external energy supply. This paper presents the results of a series of experiments focusing on various geometries of the “cold end side” for different inlet pressures and cold fractions. Specifically, the tests were conducted using different cold end orifice diameters.Energy separation and energy flux separation efficiencies are defined and used to recover characteristic properties of the vortex tube. These are used to show an appropriate scale to non-dimensionalize the energy separation effect. The experimental results indicate that there is an optimum diameter of cold end orifice for achieving maximum energy separation. The results also show that the maximum value of energy separation was always reachable at a 60% cold fraction irrespective of the orifice diameter and the inlet pressure. The results are compared with the previous studies on internal flow structure, and optimal operating parameters are shown to be consistent with a matching of orifice size with the secondary circulation being observed.     

Application of electromagnetic impact technique for welding copper-to-stainless steel sheets

The ability to manufacture a product using different metal combinations greatly increases flexibility in design and production. Joining of dissimilar metal combinations like Copper-to-Stainless Steel (Cu-to-SS) is, however, a challenging task owing to the large differences in physical and chemical properties. The application of electromagnetic (EM) impact technique is demonstrated for welding copper (Cu) to stainless steel (SS) sheets. The welding Cu-to-SS is accomplished by using Al drivers to accelerate Cu and SS work sheets. The tensile shear strength test and the metallographic studies are carried out for Cu-to-SS EM welds.     

Determination of material removal rate in wire electro-discharge machining of metal matrix composites using dimensional analysis

Wire electro-discharge machining (WEDM) is a vital process in manufacturing intricate shapes. The present work proposes a semi-empirical model for material removal rate in WEDM based on thermo-physical properties of the work piece and machining parameters such as pulse on-time and average gap voltage. The model is developed by using dimensional analysis and non-linear estimation technique such as quasi-Newton and simplex. Predictability of the proposed model is more than 99% for all work materials studied. The work materials were silicon carbide particulate reinforced aluminium matrix composites. The experiments and model prediction show significant role of coefficient of thermal expansion in WEDM of these materials. In addition, an empirical model, based on response surface method, has also been developed. The comparison of these models shows significant agreement in the predictions.