Synthesis and Spark Plasma Sintering of Mg2Si Nanopowder by Mechanical Alloying and Heat Treatment

In this investigation, a two‐step method for the preparation of magnesium silicide (Mg₂Si) nanopowder was studied. This method is known as mechanical alloying followed by heat treatment. The results showed that the compositions of the combustion products depended on the milling time, heat treatment temperature, and starting mixtures. Pure Mg₂Si nanopowder was formed after short milling time and heat treatment, from Mg and Si powders with the mole ratio of 2.1:1 (Mg:Si) at 500°C in Ar atmosphere. Using the Mg₂Si nanopowder, Mg₂Si ceramic was produced by spark plasma sintering at 800°C under 50 MPa for 15 min. Composition and structure of reactants and products were examined by X‐ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM) and high‐resolution transmission electron microscopy (HR‐TEM).     

Effect of plate-like glass fillers on the mechanical properties of dental nanocomposites

In this study, glass flakes were incorporated into the spherical nanosilica component of the dental composites and its effect on the mechanical properties of these composites was investigated. To achieve a good interfacial adhesion between matrix resin and fillers, the particles were surface treated with a silane coupling agent (γ-MPS). Composites with different plate-like and spherical nanoparticle contents were prepared and their mechanical properties, including flexural strength, flexural modulus and fracture toughness were measured. The morphology of the particles and fracture surface of the composites were studied by SEM. The distribution of the flakes in the composite was also monitored using EDXA. Statistical analysis of the data was performed with ANOVA and the Tukey’s post hoc test was at a significance level of 0.05. The results showed that the flexural modulus and fracture toughness of specimens were improved with increasing the glass flake content up to 15 vol % which then declined upon further increase due to the stacking of the flakes on each other. A good interfacial adhesion was observed between matrix resin and particles in the SEM micrographs. The results of this study suggest that incorporation of glass flakes into the dental composites containing spherical nanosilica particles may enhance their mechanical properties.     

Preparation of novel 2-(2-oxo-2H-chromen-4-yl)-3- arylthiazolidin-4-one derivatives using an efficient ionic liquid catalyst

An eco-friendly procedure for synthesis of 2-(2-oxo-2H-chromen-4-yl)-3-arylthiazolidin-4-one derivatives by three-component reaction of 2-oxo-2H-chromene-4-carbaldehydes, aromatic amines and thioglycolic acid, with tetramethylbutane-1,4-diammonium acetate as a low-cost ionic liquid catalyst under reflux condition is described. The use of an ionic liquid as a catalyst has the advantages of high yields, short reaction time and environmentally friendly reaction media.     

Injection Molding Micro‐ and Nanostructures in Thermoplastic Elastomers

Flexible polymers such as poly dimethyl siloxane (PDMS) can be patterned at the micro‐ and nanoscale by casting, for a variety of applications. This replication‐based fabrication process is relatively cheap and fast, yet injection molding offers an even faster and cheaper alternative to PDMS casting, provided thermoplastic polymers with similar mechanical properties can be used. In this paper, a thermoplastic polyurethane is evaluated for its patterning ability with an aim to forming the type of flexible structures used to measure and modulate the contractile forces of cells in tissue engineering experiments. The successful replication of grating structures is demonstrated with feature sizes as low as 100 nm and an analysis of certain processing conditions that facilitate and enhance the accuracy of this replication is presented. The results are benchmarked against an optical storage media grade polycarbonate.

     

A study on the efficiency of a capped hardening elasto-plastic model for soft clays

It is well known that the deformation and stress-resistant characteristics of fine-grained soils, especially soft clays, are significantly influenced by the soil softness. It is therefore very important to employ a model which can accurately simulate the effects of this phenomenon. A constitutive model must be able to create a balance among stress paths, the number of parameters, the process of parameter determination, and finally, the simplicity of the computational calculations.The current study investigates the performance of a two-yield surface (cone and cap yield surface) model for soft soils. The efficiency of the cap yield surface has been studied as well. The model has been calibrated by employing the data derived from previous researches for Bangkok clay. The incorporated data have been obtained from the results of CD triaxial, CU triaxial, and oedometer tests. The proposed method for the model calibration can accurately predict the triaxial test results and oedometer test stress path simultaneously. This method for predicting the soil behavior is based on the main soil characteristics taken from common soil mechanics tests. It can be widely employed for engineering practices, especially when complicated soil behavior is encountered.     

Morphology and crystallization behavior of nylon 6‐clay/neat nylon 6 bicomponent nanocomposite fibers

Nylon 6‐clay hybrid/neat nylon 6, sheath/core bicomponent nanocomposite fibers containing 4 wt % of clay in sheath section, were melt spun at different take‐up speeds. Their molecular orientation and crystalline structure were compared to those of neat nylon 6 fibers. Moreover, the morphology of the bicomponent fibers and dispersion of clay within the fibers were analyzed using scanning electron microscopy and transmission electron microscopy (TEM), respectively. Birefringence measurements showed that the orientation development in sheath part was reasonably high while core part showed negligibly low birefringence. Results of differential scanning calorimetry showed that crystallinity of bicomponent fibers was lower than that of neat nylon 6 fibers. The peaks of γ‐crystalline form were observed in the wide‐angle X‐ray diffraction of bicomponent and neat nylon 6 fibers in the whole take‐up speed, while α‐crystalline form started to appear at high speeds in bicomponent fibers. TEM micrographs revealed that the clay platelets were individually and evenly dispersed in the nylon 6 matrix. The neat nylon 6 fibers had a smooth surface while striped pattern was observed on the surface of bicomponent fibers containing clay. This was speculated to be due to thermal shrinkage of the core part after solidification of the sheath part in the spin‐line. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39996.     

Comparison of Canola and Soy Flour with Added Isocyanate as Wood Adhesives

Canola is widely grown in the northern latitudes for its vegetable oil, generating large quantities of residual, low value canola flour used as animal feed. The common wood adhesive poly(diphenylmethylene diisocyanate) (pMDI) should react with the wide variety of functional groups in proteins. Therefore, it would seem that canola flour with added pMDI could be an effective adhesive. Two main questions are addressed in this study: How do the wood adhesive properties of canola flour compare to the better-studied soy flour? How well do proteins, which contain an abundance of functional groups, cure with the very reactive pMDI? These questions were addressed using the small-scale adhesive strength test ASTM D-7998, with various adhesive formulations and bonding conditions for canola flour plus pMDI compared to soy adhesives. The more challenging wet cohesive bond strength was emphasized because the dry strengths were usually very good. Generally, soy adhesives were better than canola ones, as was the polyamidoamine-epichlorohydrin cross-linker compared to pMDI, but these generalizations can be altered by the conditions selected. Three-ply plywood tests supported the small-scale test results.     

In situ emulsion polymerization and characterization of PVAc nanocomposites including colloidal silica nanoparticles for wood specimens bonding

Polyvinyl acetate (PVAc) nanocomposites for wood adhesives containing different amounts of colloidal silica nanoparticles (CSNs) were synthesized via in situ one-step emulsion polymerization. The adhesion strength of wood specimens bonded by PVAc nanocomposites was investigated by the tensile test. Thermal properties of PVAc nanocomposites were also characterized by differential scanning calorimetry and thermogravimetric analysis. Rheological and morphological properties of the PVAc nanocomposites were investigated using rheometric mechanical spectrometry and field emission scanning electron microscopy (FESEM), respectively. The obtaining results showed that the shear strength of PVAc nanocomposite including 1 wt. % CSNs has the highest shear and tensile strength about 4.7 and 3.2 MPa, respectively. A small increment of T_g (~3 °C) and considerable increment of the ash content proved the enhancement of PVAc thermal characterization in the presence of CSNs. FESEM results showed uniform dispersion of nanoparticles throughout the PVAc matrix due to using the in situ emulsion polymerization process. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48570.     

Microscopic and macroscopic atomization characteristics of a pressure-swirl atomizer,injecting a viscous fuel oil

Combustion of heavy fuels is one of the main sources of greenhouse gases, particulate emissions, ashes, NOxand SOx. Gasification is an advanced and environmentally friendly process that generates combustible and clean gas products such as hydrogen. Some entrained flow gasifiers operate with Heavy Fuel Oil(HFO) feedstock. In this application, HFO atomization is very important in determining the performance and efficiency of the gasifiers.The atomization characteristics of HFO(Mazut) discharging from a pressure-swirl atomizer(PSA) are studied for different pressures difference(Δp) and temperatures in the atmospheric ambient. The investigated parameters include atomizer mass flow rate( _m), discharge coefficient(CD), spray cone angle(θ), breakup length(Lb), the unstable wavelength of undulations on the liquid sheet(λs), global and local SMD(sauter mean diameter) and size distribution of droplets. The characteristics of Mazut sheet breakup are deduced from the shadowgraph technique. The experiments on Mazut film breakup were compared with the predictions obtained from the liquid film breakup model. Validity of the theory for predicting maximum unstable wavelength was investigated for HFO(as a highly viscous liquid). A modification on the formulation of maximum unstable wavelength was presented for HFO. SMD decreases by getting far from the atomizer. The measurement for SMD and θ were compared with the available correlations. The comparisons of the available correlations with the measurements of SMD andθ show a good agreement for Ballester and Varde correlations, respectively. The results show that the experimental sizing data could be presented by Rosin-Rammler distributions very well at different pressure difference and temperatures.     

Dynamically vulcanized thermoplastic elastomer nanocomposites based on linear low-density polyethylene/styrene-butadiene rubber/nanoclay/bitumen: morphology and rheological behavior

Dynamically crosslinked thermoplastic elastomer nanocomposites were synthesized as modifier for the bitumen binder-based asphalts. Linear low-density polyethylene (LLDPE) and styrene-butadiene rubber (SBR), with the ratio of 80/20, bitumen, and organically modified clay (OC) were all melt mixed in the presence of the sulfur curing system. The proposed mixing was carried out in an internal mixer at 160 °C with a rotor speed of 120 rpm. To enhance the molecular interactions between the polymer phases and the clay silicate layers, maleic anhydride-grafted LLDPE (PE-g-MA) with the maleiation degree of 50% was also incorporated into the mixture. Observation of the composite samples, using the scanning electron microscopy (SEM), revealed the matrix dispersed type of morphology for all dynamically vulcanized samples. X-ray diffraction (XRD) and transmission electron microscopy (TEM) examinations evidenced the exfoliation of the clay silicate layers with good dispersion. Rheomechanical spectrometry (RMS) was performed on the prepared nanocomposites. All dynamically vulcanized nanocomposites comprising 2.5% of OC exhibited shear-thinning behavior and non-terminal characteristics with a low frequency range. These indicate the formation of three-dimensional physical networks by the clay nanolayers throughout the LLDPE matrix. The presence of the bitumen in the composition of the prepared nanocomposites improved the flowability of the samples. This is a promising feature of the prepared nanocomposites to be used as an elastic and resistant modifier in the composition of the bitumen-based asphalts.