Asymptotic Stability of a Rate Control System With Communication Delays

We study the issue of asymptotic stability of a family of rate control algorithms with communication delays between network elements and extend our earlier results: First, we derive delay-dependent stability conditions with a family of well-known utility and resource price functions when a finite upper bound is known on the feedback delay. These conditions are shown to be consistent with known stability conditions in two extreme cases-no delay or an arbitrarily large delay. Secondly, we provide a lower bound on the convergence rate with the same utility and resource price functions when delay-independent stability conditions hold.     

GIS Approach of Delineation and Risk Assessment of Areas Affected by Arsenic Pollution in Drinking Water

The objective of this study is to analyze health effects of arsenic pollution of drinking water using a geographical information system (GIS). The paper reports the regional impact of arsenic contamination in six administrative blocks of the central part of the Murshidabad district, West Bengal, India. In this area about 1,248,580 people are exposed to arsenic pollution out of whom 388,316 people are exposed to arsenic concentrations above 0.05?mg/L, the WHO maximum permissible level of arsenic in drinking water. The study estimates that 65% of the total area of the six blocks has arsenic concentrations below 0.05?mg/L, 26.12% of the area has arsenic concentrations above 0.05?mg/L, and for the rest of the area no arsenic distribution data available. The total number of expected death cases has been estimated considering the percent of risk involved in a concentration range and corresponding total population using such water for drinking purpose. The analysis forecasts that 11,890 people may risk death due to arsenic pollution in the whole life span. The maximum number of death cases is expected in Domkal and Beldanga 1 blocks and the minimum number of death cases is expected in Block Bhagabangola 2. This study also reports a comparison between the theoretical expectation of death cases and actual reported arsenicosis cases for the Domkal block. The areas of theoretical expectation and the areas of actually reported cases match fairly well except in a few cases. The present study helps planning and implementing of priority-based arsenic mitigation options.     

An enhanced Radial Basis Function Network for voltage stability monitoring considering multiple contingencies

This paper proposes a scheme for online voltage stability monitoring using an enhanced Radial Basis Function Network (RBFN). A single RBFN is used to predict MW margins for different contingencies. A sequential learning strategy is used along with a regularization technique to design the RBFN and the weights in the output layer are determined by using linear optimization. The proposed network can be adapted with changing operating scenario of the power system. A network pruning strategy is used to limit the growth of the network size due to adaptive training. The proposed scheme is applied on the New England 39-bus power system model.     

Effect of Disorder on Electronic,Magnetic, and Optical Properties of Co2CrZ Heusler Alloys (Z = Al,Ga, Si,Ge)

This paper presents the effect of disorder on electronic, magnetic, and optical properties of Co₂CrZ (Z = Al, Si, Ga, Ge) Heusler alloy using density functional theory. Binary mixing is the most common form of atomic disorder in these compounds. We have considered three types of disorders: DO ₃, A2, and B2 disorder which corresponds to X-Y, X-Z, and Y-Z mixing, respectively. After structural optimization, we found that A2 disorder has high formation energy and is most unlikely to occur. The half-metallic nature of the alloy is destroyed in the presence of DO ₃ and A2 disorder. The destruction of half-metallicity is due to reconstruction of energy states. B2 disorder retains the half-metallic nature of the alloy but spin-polarization value is reduced slightly as compared to the ordered alloy. In addition, the optical properties such as dielectric function, refractive index, absorption spectra, optical conductivity, reflectivity, and energy loss function of these alloys have also been investigated.     

An integrated framework for managing sensor data uncertainty using cloud computing

In recent years, an increasing number of data-intensive applications deal with continuously changing data objects (CCDOs), such as data streams from sensors and tracking devices. In these applications, the underlying data management system must support new types of spatiotemporal queries that refer to the spatiotemporal trajectories of the CCDOs. In contrast to traditional data objects, CCDOs have continuously changing attributes. Therefore, the spatiotemporal relation between any two CCDOs can change over time. This problem can be more complicated, since the CCDO trajectories are associated with a degree of uncertainty at every point in time. This is due to the fact that databases can only be discretely updated. The paper formally presents a comprehensive framework for managing CCDOs with insights into the spatiotemporal uncertainty problem and presents an original parallel-processing solution for efficiently managing the uncertainty using the map-reduce platform of cloud computing.     

Inverted emulsion polymerization route to polyaniline‐3D nanofiber network using sulfonated‐p‐cresol as novel dopant

Sulfonated‐p‐cresol (SPC) was used as novel dopant for the first time in the synthesis of polyaniline in 3D nanofiber networks (PANI‐3D). Polyaniline in 3D nanofiber network was prepared using organic solvent soluble benzoyl peroxide as oxidizing agent in presence of SPC and sodium lauryl sulfate (SLS) surfactant via inverted emulsion polymerization pathway. The influence of synthesis conditions such as the concentration of the reactants, stirring/static condition, and temperature etc., on the properties and formation of polyaniline nanofiber network were investigated. Polyaniline in 3D nanofiber network with 40–160 nm (diameter), high yield (134 wt % with respect to aniline used), and reasonably good conductivity (0.1 S/cm) was obtained in 24 h time. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Temperature–enthalpy curve for energy targeting of distillation columns

The temperature–enthalpy (T–H) diagram of a distillation column at practical near-minimum thermodynamic condition (PNMTC) or the column grand composite curve (CGCC) is a useful representation for energy targeting studies and may be generated from a converged simulation of a base-case column design. The calculation procedure for the CGCC involves determination of the net enthalpy deficit at each stage by generating envelopes from either the condenser end (top-down approach) or the reboiler end (bottom-up approach). However, the values calculated by the two approaches differ for stages with feeds because existing procedures for CGCC generation do not consider the enthalpy balances at the feed stages. In fact, the net enthalpy deficits at feed stages calculated by both approaches are erroneous even for the simplest case of binary distillation. A feed stage correction (FSC) that rigorously considers the mass and enthalpy balance equations at feed stages is proposed in this work to resolve the discrepancy. Instead of assuming that the compositions obtained from the converged simulation for a feed stage will remain unchanged at PNMTC, the pinched compositions for the feed are determined by the intersection of the equilibrium curve and the feed q-line. Rather than perform an additional flash calculation to establish the pinched feed compositions, a quadratic approximation is developed here for column targeting purposes by assuming the relative volatility obtained from the simulation to remain constant in the neighborhood of the feed stage. The proposed FSC ensures that the CGCC is identical whether the calculations are performed by the top-down approach or the bottom-up approach. The effect of the FSC on the targets for energy conservation by reflux modification, feed conditioning, and introduction of side reboilers/condensers is discussed. As the energy target for reflux modification is determined by the CGCC pinch which typically occurs at or close to the feed location, the significance of the FSC on the reflux modification target is highlighted through several case studies including a complex column featuring multiple feeds and consequently multiple pinch points. The CGCCs for these case studies are generated by a computer program based on the FSC and a single analytical equation for the calculation of the net enthalpy deficits that allows every stage to have a feed, liquid product, vapor product, and side exchanger. The studies show that the reflux modification targets may be erroneous in many cases, if the FSC is ignored.     

Factors controlling the time evolution of the corrosion potential of aluminum in alkaline solutions

The mechanism of corrosion of 99.99% purity aluminum in alkaline solutions was investigated, through detailed examination of open-circuit potential transients. These transients displayed a characteristic time dependence, in which the potential first decreased over a few seconds to a minimum of −1.7 to −1.9 V vs. Ag/AgCl, and then slowly increased over a period of hours. The value of the minimum potential of electropolished foils, along with its dependence on pH and aluminate ion concentration, indicated that it was determined by the Nernst potential for the oxidation of surface aluminum hydride (AlH₃). This finding supports the direct role of hydride in the dissolution process. The increase of anodic polarization after the minimum potential occurred in two stages, the first correlated with the buildup of surface hydride, and the second with surface enrichment of Cu and Fe impurities.     

Effect of curing conditions and ionic additives on properties of fly ash-lime compacts

In the present work the reaction between fly ash and lime in fly ash-lime compacts under water curing and steam curing conditions was studied thoroughly in relation to the processing conditions. Fly ash from different sources were collected, characterized, mixed with lime in different ratios and compacted. The compacts were cured with water and steam separately. The reduction in the free CaO content in these compacts was measured as a function of curing time and curing process. Role of two ionic additives, FeCl₃ and MgCl₂, on the reaction between fly ash and lime was also investigated by measuring the free CaO content. Kinetics of these reactions was studied by determining the reaction order and rate constants with respect to the free CaO content and it was observed that the curing conditions and additives affected the reaction kinetics significantly.     

A novel electrical-mobility-based instrument for total number concentration measurements of ultrafine particles

A novel electrical-mobility-based technique to measure total particle number concentration over a selected size range is presented. Charged particles are condensed out onto an electrode that is shaped such that the product of its transfer function and the particle charging efficiency is a constant, independent of particle size. The resulting total current is then proportional to the number concentration of the sampled particles over the collected size range. The theoretical approach for the calculation of the electrode shape function is described. The extension of this technique for measurement of higher moments of the particle size distributions over a desired size range is briefly discussed.This concept is used to design a new instrument, called the tailored electrode concentration sensor (TECS). For validation of the theoretical concept, the collection electrode in the TECS instrument is designed for concentration measurements over a size range of 30–90 nm. In the TECS, the collection section is located downstream of an electrostatic precipitator section, where the sampled flow is split into aerosol and sheath flows, similar to the design of the MEAS [Ranjan, M., & Dhaniyala, S., (2007), Theory and design of a new miniature electrical-mobility aerosol spectrometer, Journal of Aerosol Science, 38(9), 950–963]. This results in a compact, low pressure drop instrument. Experimental results confirm that the response of the optimally-shaped electrode in the TECS system is only proportional to total number concentration over the selected size range.