Wideband HBT circuits for operation above 10 GHz and power supply voltages below 5 V

Single-stage and two-stage differential cascode amplifiers, and a 2:1 multiplexer, fabricated in InP/InGaAs HBT technology and powered from less than 5 V supplies, are presented. The amplifiers have typical DC gains of 21 and 33 dB, respectively, and unity-gain bandwidths in excess of 15 GHz, with approximately 20 dB gain at 10 GHz. The multiplexer was tested at rates up to 20 Gbit/s.<>     

Magneto-resistance and Excess Conductivity Studies of Tl(Ba2−y Mg y )Ca 2 Cu 3 O 10−δ Samples

The flux pinning characteristics of T l(B a _2?y M g _y )C a ₂ C u ₃ O _10?δ(0.0≤y≤ 1.5) samples have been studied under the influence of various dc magnetic fields in the light of thermally activated flux flow model. It was observed form the magneto resistivity measurements that the activation energy U has been increased in the sample with Mg incorporation of y=0.5, however, it is decreased in the samples with higher Mg doping. This shows that lower Mg doping concentration promotes enhancement, whereas its higher concentration suppresses the flux pinning characteristics of Tl(Ba _2?yMg _y )Ca ₂Cu ₃ O _10?δ (0.0 ≤y≤1.5) samples. The excess conductivity analysis of Tl(Ba _2?yMg _y )Ca ₂Cu ₃ O _10?δ (0.0 ≤ y ≤ 1.5) samples has shown that the coherence length along the c-axis ξ _c(0), the interlayer coupling J, the phase relaxation time of the carriers τ _? , and the Fermi velocity v _F of the carriers are suppressed with Mg doping. However, the values of B _c0(T), B _c1(T), and J _c(0) are enhanced which complement the magnetoresistivity analysis. These results showed that the flux pinning characteristics are enhanced for lower doping concentration of Mg at the charge reservoir layer sites.     

Development of Al356/SiCp cast composites by injection of SiCp containing composite powders

One of the great challenges of producing cast metal matrix composites is the agglomeration tendency of the reinforcements. This would normally result in poor distribution of the particles, high porosity content, and low mechanical properties. In the present work, a new method for uniform distribution of very fine SiC particles with average size of less than 3 μm was employed. The key idea was to allow for gradual in situ release of properly wetted SiC particles in the liquid metal. For this purpose, SiC particles were injected into the melt in three different forms, i.e., untreated SiC_p, milled particulate Al–SiC_p composite powder, and milled particulate Al–SiC_p–Mg composite powder. The resultant composite slurries were then cast from either fully liquid (stir casting) or semisolid (compocasting) state. Consequently, the effects of the casting method and the type of the injected powder on the microstructural characteristics as well as the mechanical properties of the cast composites were investigated. The results showed that the distribution of SiC particles in the matrix and the porosity content of the composites were greatly improved by injecting milled composite powders instead of untreated-SiC particles into the melt. Casting from semisolid state instead of fully liquid state had similar effects. The average size of SiC particles incorporated into the matrix was also significantly reduced from about 8 to 3 μm by injecting milled composite powders. The ultimate tensile strength, yield strength and elongation of Al356/5 vol.%SiC_p composite manufactured by compocasting of the (Al–SiC_p–Mg)_cp injected melt were increased by 90%, 103% and 135%, respectively, compared to those of the composite manufactured by stir casting of the untreated-SiC_p injected melt.     

Seismic performance assessment of steel moment frames with generic Locally Reinforced connections

Seismic performance of Steel Moment-Resisting Frames (SMRFs) with generic Locally-Reinforced (LR) connections has been investigated incorporating both earthquake-induced and modeling uncertainties. The LR connections were numerically modeled following the suggestions made by previous researches and were used to numerically model three buildings with various heights which were designed regarding the specifications of current standards. For reflecting the record-to-record (RTR) variability, the Incremental Dynamic Analysis (IDA) procedure was utilized within the Performance-Based Earthquake Engineering (PBEE) methodology. In this regard, the structures’ performance in a multitude of structural response levels was probabilistically assessed in “considering” and “neglecting” conditions of modeling uncertainties. For performing the modeling uncertainty analysis, a number of modeling parameters that best reflected the structures’ variability due to lack of knowledge were selected as random variables. Perturbing the modeling variables from their median values, a set of sensitivity IDAs were performed and a polynomial response surface was established. Incorporation of the response surface in conjunction with Monte Carlo simulation led, finally, to a fully probabilistic performance evaluation of the studied structures in varied structural response levels. The effect of modeling uncertainties in altering the predicted performances was found to be insignificant in the range of buildings and structural elements studied in this article.     

Design of explicit model predictive control for constrained linear systems with disturbances

On-line model predictive control approaches require the online solution of an optimization problem. In contrast, the explicit model predictive control moves major part of computation offline. Therefore, eMPC enables one to implement a MPC in real time for wide range of fast systems. The eMPC approach requires the exact system model and results a piecewise affine control law defined on a polyhedral partition in the state space. As an important limitation, disturbances may reduce performance of the explicit model predictive control. This paper presents efficient approach for handling the problem of using eMPC for constrained systems with disturbances. It proposes an approach to improve performance of the closed loop system by designing a suitable state and disturbance estimator. Conditions for observability of the disturbances are considered and it is depicted that applying the disturbance’s estimation leads to rejection of the response error. It is also shown that the proposed approach prevents the reduction of feasible space. Simulation results illustrate the advantages of this approach.     

An efficient method of designing dual‐ and wide‐band power dividers with arbitrary power division

Capability of microstrip nonuniform transmission lines (MNTLs) for construction of dual‐band and broadband unequal Wilkinson power dividers with arbitrary‐way, arbitrary frequency band operations, and arbitrary power divisions is evaluated. Also, the MNTL transformers are introduced for dual‐band/broadband matching of the unequal output impedances of the MNTL power divider with arbitrary output terminal impedances. The strip width of MNTLs is considered variable and is written as a truncated Fourier series expansion. To show the validity of the design procedure, three experimental MNTL Wilkinson power dividers, which are dual‐band two‐ and three‐way power dividers with different power divisions working at 1 and 3.4 GHz and one broadband equal power divider working from 0.4 to 1.8 GHz, have been designed and fabricated. In the first ones with power division of 1.5, outputs isolation and ports matching of less than ?30 dB are achieved. Next, an extended recombinant structure is presented for achieving three‐way MNTL power dividers with dual‐band operation. The measured isolation between outputs and ports matching are better than 30 dB and measured forward transmissions are between ?4.87 and ?5.45 in two passbands of the divider. Also, for the proposed broadband divider, the measured isolation between the outputs is better than 13 dB in 127% desired bandwidth. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Time-bandwidth product of the photonic time-stretched analog-to-digital converter

The time-bandwidth product of the photonic time-stretched system is modeled in terms of physical system parameters. Using the time-bandwidth product as figure-of-merit, the performances of optical double-sideband and single-sideband (SSB) intensity modulation are compared, and optical SSB intensity modulation is identified as a potential solution to extend the system's time-bandwidth product. An SSB-modulated time-stretched system is theoretically analyzed and experimentally demonstrated. As an important practical consideration, the analytical model relating the system performance to the phase and amplitude mismatches in the SSB modulator is presented. The results show that the system is tolerant to such unavoidable mismatches. Experiments using commercially available components suggest that the dispersion-induced power penalty can be kept below 2.5 dB over 4 - 20 GHz bandwidth for any stretch factor. Additional experiments demonstrating 120-GSamples/s real-time digitization of a 20-GHz SSB-modulated signal are also reported.     

Digital adaptive phase noise reduction in coherent optical links

Coherent optical links enable high-density constellations and, consequently, a higher throughput. However, the phase noise associated with the transmitter and the receiver lasers is a challenging issue in coherent lightwave systems. The authors present an approach that relies on using digital signal processing techniques to compensate for the laser phase-noise effects. The proposed approach exploits the digital processing power to address the problems arising from optical imperfections. The authors present an adaptive filtering scheme that reduces the effect of the laser phase noise and, consequently, relaxes the laser linewidth requirement. The proposed approach shows how the signal processing techniques can be exploited to compensate for the optical impairments by utilizing the continuing scale down in size and power in very large scale integration (VLSI) technology.