IBLEACH: intra-balanced LEACH protocol for wireless sensor networks

Wireless sensor networks (WSNs) are composed of many low cost, low power devices with sensing, local processing and wireless communication capabilities. Recent advances in wireless networks have led to many new protocols specifically designed for WSNs where energy awareness is an essential consideration. Most of the attention, however, has been given to the routing protocols since they might differ depending on the application and network architecture. Minimizing energy dissipation and maximizing network lifetime are important issues in the design of routing protocols for WSNs. In this paper, the low-energy adaptive clustering hierarchy (LEACH) routing protocol is considered and improved. We propose a clustering routing protocol named intra-balanced LEACH (IBLEACH), which extends LEACH protocol by balancing the energy consumption in the network. The simulation results show that IBLEACH outperforms LEACH and the existing improvements of LEACH in terms of network lifetime and energy consumption minimization.     

Direct Growth and Photoluminescence of SiO<Subscript>x</Subscript> Nanowires and Aligned Nanocakes by Simple Carbothermal Evaporation

The growth of SiO_x nanowires and nanocakes on an Au-coated n-type-Silicon (100) substrate was achieved via carbothermal evaporation. The effects of the Au layer thickness and the rapid heating rate on the morphology of obtained SiO_x nanowires were investigated. A broad emission band from 290 to 600 nm was observed in the photoluminescence (PL) spectrum of these nanowires. There are four PL peaks: one blue emission peak 485 nm (2.56 eV) two green bands centered at 502 nm (2.47 eV) and 524 nm (2.37 eV) for nanocakes and one ultraviolet emission peak at 350 nm (3.54 eV) and a hemisphere curve over the bluish green area taken for SiO_x nanowires. These emissions may be related to the various oxygen defects and twofold coordinated silicon lone pair centers.     

Adaptation of machining toolpath to distorted geometries: application to remove a constant thickness on rough casting prosthesis

This study proposes a method to adapt the geometry of the toolpath to a specified target. In the case study presented, the geometrical target is to remove a constant thickness on the rough workpiece. This case is normally present in the polishing of the femoral component of knee prostheses. In fact, an operator carries out these operations manually. The aim of this study is to contribute to the automation of prosthesis production, notably, in the preparation of surface polishing. The proposed method can deform and adapt a toolpath to ensure the required geometry of the machined surface. The proposed toolpath deformation method is composed of three steps: alignment, toolpath deformation, and toolpath smoothing. Alignment between the measured surface of the roughcast prostheses and the nominal toolpath is carried out by an Iterative Closest Point (ICP) algorithm. The principle of this algorithm is to find the optimal rigid transformation to readjust the toolpath on the measured surface. Subsequently, the toolpath is deformed to remove the constant thickness of the roughcast prostheses. Next, to increase the machined quality, a smoothing stage is carried out on the obtained toolpath. Experimental tests on industrial prostheses geometry are conducted to validate the effectiveness of this method.     

The effect of post-treatments on the powder morphology of titanium dioxide (TiO2) powders synthesized for cold spray

In this study, a novel synthesis method of TiO₂ powders that can be cold sprayed is presented. The synthesis technique is a simple hydrolysis method of titanyl sulfate (TiOSO₄) in distilled water with a small addition of inorganic salt. At a relatively low hydrolysis temperature, pure anatase TiO₂ can be obtained and post-synthesis treatments (annealing or hydrothermal treatment) do not alter this phase structure. The powder is agglomerated with fine nano primary particles, with different post-synthesis treatments leading to different TiO₂ nanostructures. Annealing causes a significant growth of primary particles with the existence of internal pores within a particle. On the other hand, hydrothermal treatment produces a unique oriented agglomeration structure where the primary particles are agglomerated in one single crystal axes. It is believed that the synergistic effect of inorganic ion adsorption and post-treatments results in the observed nanostructures. After cold spraying, it is revealed that these TiO₂ powders could be deposited via supersonic solid phase deposition (cold spray).     

Efficient routing for IP subnet VLAN over Ethernet

Existing IP routing algorithms have been developed mainly for non‐VLAN networks. For these routing algorithms to work, an end station must be attached to its associated network. The introduction of VLAN has, however, allowed the physical location of the end station to be changed from time to time. Therefore, some extra mechanism is required to support routing in VLAN environment. Existing approaches have some drawbacks in terms of inefficiency in traffic forwarding and switch software complexity. In this paper, a simple and efficient method for routing over IP subnet VLAN in Ethernet is proposed. This method has been implemented in hardware and found to work correctly. Various measurements and analyses have been performed to verify the efficiency of this protocol. Copyright © 2002 John Wiley & Sons, Ltd.     

Editorial: Special Issue on High Performace Distributed Computing

The Journal of Supercomputing -     

Calibration of a Photodiode Array Spectrometer Against the Copper Point

This paper describes a method to calibrate photodiode array spectrometers in the spectral radiance mode using a fixed-point blackbody as a reference source. Fixed-point blackbodies are characterized by their excellent emissivity, uniformity, and stability, which make them superior to both conventional standard lamps and variable temperature blackbodies. The temperature of these fixed points is accurately determined being traceable to either the International Temperature Scale (ITS-90) or thermodynamically through radiometric standards. The potential advantage of the fixed-point traceability chain is that it can be universally reproduced without recourse to any hierarchical calibrations or standards. The paper presents the calibration system and discusses the limitations of such an approach. The method used obtained an uncertainty of around 1.4 % ( \(k = 2\) ) associated with radiance responsivity across the spectral region from 550 nm to 1050 nm, which is comparable to what is readily achieved with a lamp-tile or lamp-illuminated spherical source.     

Stray light correction for diode-array-based spectrometers using a monochromator

Photodiode-array-based spectrometers are increasingly being used in a wide variety of applications. However, the signal measured by this type of instrument often is not what is anticipated by the user and is often subject to contamination from stray light. This paper describes an efficient and low-cost stray light correction approach based on a relatively simple system using a monochromator-based source. The paper further discusses the limitations of using a monochromator instead of a laser, as used by previous researchers, and its impact on the quality of the stray light correction. The reliability and robustness of the stray light correction matrix generated have been studied and are also reported.     

Temperature and nonlinearity corrections for a photodiode array spectrometer used in the field

Temperature and nonlinearity effects are two important factors that limit the use of photodiode array spectrometers. Usually the spectrometer is calibrated at a known temperature against a reference source of a particular spectral radiance, and then it is used at different temperatures to measure sources of different spectral radiances. These factors are expected to be problematic for nontemperature-stabilized instruments used for in-the-field experiments, where the radiant power of the site changes continuously with the sun tilt. This paper describes the effect of ambient temperature on a nontemperature-stabilized linear photodiode array spectrometer over the temperature range from 5?°C to 40?°C. The nonlinearity effects on both signal amplification and different levels of radiant power have also been studied and are presented in this paper.