Fatigue Crack Tip Plasticity for Inclined Cracks

The evaluation of the crack tip deformation is essential to the estimation of crack growth under either static or cyclic loading. A 3-D elastic–plastic finite element analysis was developed to simulate the crack tip deformation along mixed mode inclined edge cracks in a steel plate subjected to either monotonic or cyclic loading at selected R-ratios. In this paper, two types of crack configurations were investigated: inclined cracks with equal inclined lengths (EICL) and inclined cracks with equal horizontal projection length (ECHP). The development of the monotonic (Δm) and cyclic (Δc) crack tip plastically zones and the monotonic (CTOD) and cyclic (ΔCTOD) crack tip opening displacements were traced to find the effect of the crack inclination angle, which significantly affected the size and shape of the crack tip plastic zone. The finite element results compared well with the analytical results based on modified Dugdale’s model. It was observed that Mode II has a significant effect on the plastic zone in the case of equal inclined crack length (EICL), i.e., Mode II increases as the crack angle decreases. Also, it is interesting to note that for the EICL case, the magnitude of Δc is delayed to appear with decreasing the inclination angle, for example, for θ?=?90° the cyclic plastic zone appeared at Δσ?=?103.32 MPa, while for θ?=?45° the cyclic plastic zone appeared at Δσ?=?132.84 MPa. Whereas, the variation of monotonic and cyclic plastic zone size in the equal crack horizontal projection (ECHP) case is not affected by the crack inclination angle. Furthermore, it was observed that the static crack tip opening displacement (CTOD) and the cyclic (ΔCTOD) are independent of the crack inclination angle in case of ECHP, due to such cracks take into consideration the effect of inclination angle through its length.     

Adaptation of machining toolpath to distorted geometries: application to remove a constant thickness on rough casting prosthesis

This study proposes a method to adapt the geometry of the toolpath to a specified target. In the case study presented, the geometrical target is to remove a constant thickness on the rough workpiece. This case is normally present in the polishing of the femoral component of knee prostheses. In fact, an operator carries out these operations manually. The aim of this study is to contribute to the automation of prosthesis production, notably, in the preparation of surface polishing. The proposed method can deform and adapt a toolpath to ensure the required geometry of the machined surface. The proposed toolpath deformation method is composed of three steps: alignment, toolpath deformation, and toolpath smoothing. Alignment between the measured surface of the roughcast prostheses and the nominal toolpath is carried out by an Iterative Closest Point (ICP) algorithm. The principle of this algorithm is to find the optimal rigid transformation to readjust the toolpath on the measured surface. Subsequently, the toolpath is deformed to remove the constant thickness of the roughcast prostheses. Next, to increase the machined quality, a smoothing stage is carried out on the obtained toolpath. Experimental tests on industrial prostheses geometry are conducted to validate the effectiveness of this method.     

Xylitol: A Review on Bioproduction,Application, Health Benefits,and Related Safety Issues

Xylitol is a pentahydroxy sugar-alcohol which exists in a very low quantity in fruits and vegetables (plums, strawberries, cauliflower, and pumpkin). On commercial scale, xylitol can be produced by chemical and biotechnological processes. Chemical production is costly and extensive in purification steps. However, biotechnological method utilizes agricultural and forestry wastes which offer the possibilities of economic production of xylitol by reducing required energy. The precursor xylose is produced from agricultural biomass by chemical and enzymatic hydrolysis and can be converted to xylitol primarily by yeast strain. Hydrolysis under acidic condition is the more commonly used practice influenced by various process parameters. Various fermentation process inhibitors are produced during chemical hydrolysis that reduce xylitol production, a detoxification step is, therefore, necessary. Biotechnological xylitol production is an integral process of microbial species belonging to Candida genus which is influenced by various process parameters such as pH, temperature, time, nitrogen source, and yeast extract level. Xylitol has application and potential for food and pharmaceutical industries. It is a functional sweetener as it has prebiotic effects which can reduce blood glucose, triglyceride, and cholesterol level. This review describes recent research developments related to bioproduction of xylitol from agricultural wastes, application, health, and safety issues.     

Analysis of cooling curve to determine the end point of freezing

The cooling curve method used for the measurement of freezing point of food is further analyzed to explore whether it can be used to identify the end point of freezing or glass transition. In this method, slope of the cooling curve is determined and plotted as a function of time to identify the end point of freezing (T′_m). Initially, the slope is decreased and then reached a minimum value, which is identified as the nucleation of ice. Then the slope is increased until the end point of freezing. The end point of freezing is identified when the slope starts to decrease from its highest value or plateau. Sucrose solutions and starch gels were used to measure its T′_m in identifying validity of the proposed method. The measured values of T′_m by the proposed method is very close to the literature values.     

The role of the experimental data base used to identify material parameters in predicting the cyclic plastic response of an austenitic steel

The first objective of this paper investigates the influence of the previous strain history on ratcheting. New tests were performed where different strain-controlled histories have been applied prior to ratcheting tests. It is demonstrated that under the same conditions, one can observe ratcheting, plastic shakedown or elasticity according to the prior strain-controlled history. The second objective points out the correlation between the experimental data base devoted to the identification of the material parameters and the quality of the predictions in cyclic plasticity. The results suggest that the choice of the tests should be closely linked to the capabilities of the model. In particular, the presence of non proportional strain-controlled tests in the data base may be not a good choice if the model itself is not able to represent explicitly such a character. All tests considered here were performed on 304L SS at room temperature.     

The effect of post-treatments on the powder morphology of titanium dioxide (TiO2) powders synthesized for cold spray

In this study, a novel synthesis method of TiO₂ powders that can be cold sprayed is presented. The synthesis technique is a simple hydrolysis method of titanyl sulfate (TiOSO₄) in distilled water with a small addition of inorganic salt. At a relatively low hydrolysis temperature, pure anatase TiO₂ can be obtained and post-synthesis treatments (annealing or hydrothermal treatment) do not alter this phase structure. The powder is agglomerated with fine nano primary particles, with different post-synthesis treatments leading to different TiO₂ nanostructures. Annealing causes a significant growth of primary particles with the existence of internal pores within a particle. On the other hand, hydrothermal treatment produces a unique oriented agglomeration structure where the primary particles are agglomerated in one single crystal axes. It is believed that the synergistic effect of inorganic ion adsorption and post-treatments results in the observed nanostructures. After cold spraying, it is revealed that these TiO₂ powders could be deposited via supersonic solid phase deposition (cold spray).     

Efficient routing for IP subnet VLAN over Ethernet

Existing IP routing algorithms have been developed mainly for non‐VLAN networks. For these routing algorithms to work, an end station must be attached to its associated network. The introduction of VLAN has, however, allowed the physical location of the end station to be changed from time to time. Therefore, some extra mechanism is required to support routing in VLAN environment. Existing approaches have some drawbacks in terms of inefficiency in traffic forwarding and switch software complexity. In this paper, a simple and efficient method for routing over IP subnet VLAN in Ethernet is proposed. This method has been implemented in hardware and found to work correctly. Various measurements and analyses have been performed to verify the efficiency of this protocol. Copyright © 2002 John Wiley & Sons, Ltd.     

Editorial: Special Issue on High Performace Distributed Computing

The Journal of Supercomputing -     

Calibration of a Photodiode Array Spectrometer Against the Copper Point

This paper describes a method to calibrate photodiode array spectrometers in the spectral radiance mode using a fixed-point blackbody as a reference source. Fixed-point blackbodies are characterized by their excellent emissivity, uniformity, and stability, which make them superior to both conventional standard lamps and variable temperature blackbodies. The temperature of these fixed points is accurately determined being traceable to either the International Temperature Scale (ITS-90) or thermodynamically through radiometric standards. The potential advantage of the fixed-point traceability chain is that it can be universally reproduced without recourse to any hierarchical calibrations or standards. The paper presents the calibration system and discusses the limitations of such an approach. The method used obtained an uncertainty of around 1.4 % ( \(k = 2\) ) associated with radiance responsivity across the spectral region from 550 nm to 1050 nm, which is comparable to what is readily achieved with a lamp-tile or lamp-illuminated spherical source.