Phenol recovery with tributyl phosphate in a hollow fiber membrane contactor: Experimental and model analysis

The extraction and stripping of phenol using a solution of tributyl phosphate in kerosene in a hydrophobic polypropylene hollow fiber membrane contactor has been studied. The effect of the aqueous and the organic phase flow rates on the overall mass transfer coefficient for both extraction and stripping steps was investigated. Experimental values of the overall mass transfer coefficient were determined and compared with predicted values from the resistance in series model. Results showed that the overall mass transfer coefficients for extraction were about one order of magnitude greater than those measured during the stripping process. The experimental values were in good agreement with the predicted values for the extraction module. However, the predicted values were slightly overestimated for the stripping module. The individual mass transfer resistances were analyzed and the rate-controlling steps of mass transfer were also identified in both extraction and stripping modules. The major resistance in extraction and stripping was in the aqueous phase and in the membrane phase, respectively.     

Aqueous leachability of metakaolin-based geopolymers with molar ratios of Si/Al = 1.5-4

The leachability in water of metakaolin based geopolymers with molar ratios of Na/Al = 1 and Si/Al = 1.5-4.0 has been investigated in order to optimise the composition for the immobilisation of nuclear waste. Formulations with Si/Al of around 2 are the most suitable using the ASTM/PCT leach test method. The variability of the leach results is discussed with reference to the microstructure, compressive strength and the degree of polymerisation of the geopolymers as observed here by solid state nuclear magnetic resonance, XRD and infrared measurements.     

Osmolality and buffering agents in soft contact lens packaging solutions.

AIM: The study determined the effects of packaging solution osmolality and buffering agent on soft contact lens parameters. METHODS: One lens type from each FDA contact lens material category was equilibrated to phosphate buffered saline (PBS) or borate buffered saline (BBS), at three osmolality concentrations: 270, 310 and 414 mOsmol/kg. Lens diameter (LD), base curve (BOZR) and back vertex power (BVP) were measured and compared to nominal packaging label values. RESULTS: Statistically significant differences were found in all three parameters across all osmolality levels for both buffering agents. Etafilcon A showed the largest amount of parameter change, followed by alphafilcon A and balafilcon A. Lotrafilcon A was the least affected. LD of alphafilcon A lenses (greater than +/- 0.2 mm) and BVP of lotrafilcon A and etafilcon A lenses (greater than +/- 0.25 D) measured outside the International Standards Organization (ISO) tolerance from their packaging labels when measured in solutions that mimicked their packaging solutions. CONCLUSION: Osmolality and buffering agents influence lens parameters. Packaging solutions can vary the parameters of some lens types from their nominal value to outside the tolerance range set by ISO.     

Prediction of breakpoint distance in microcellular environments

Experimental studies of path loss distance dependency in line-of-sight microcellular propagation almost always show a dual-slope behaviour. However, there is disagreement in the literature over the best way to predict the breakpoint distance that delineates the change in path loss distance dependency. A new breakpoint equation is presented, the predictions of which are in excellent agreement with breakpoint distances observed in various propagation studies     

Evoked potential abnormality scores are a useful measure of disease burden in relapsing-remitting multiple sclerosis

OBJECTIVES: To identify the incidence and the success of endourologic therapy for symptomatic bladder-related calculi in simultaneous kidney-pancreas (SPK) transplant patients with bladder drainage. METHODS: A retrospective review of 300 SPK transplant patients with bladder drainage, treated at the University of Wisconsin, Madison from December 1985 to November 1995, is presented. A 3% incidence of bladder calculi was identified. All patients underwent cystolitholapaxy using electrohydraulic lithotripsy and endoscopic suture removal. Follow-up ranged from 15 to 86 months. RESULTS: A 100% stone-free rate was achieved after cystolitholapaxy and endoscopic suture removal. Two patients (22%) developed postprocedural urinary tract infections. No pancreaticoduodenocystotomy leaks or further complications were identified. CONCLUSIONS: SPK transplant patients with nonabsorbable sutures used for the duodenocystotomy anastomosis are at an increased risk for bladder calculi. Cystolitholapaxy with electrohydraulic lithotripsy is a safe and effective treatment for these suture-related stones.     

Polycyclic aromatic hydrocarbon-DNA adducts in human placenta and modulation by CYP1A1 induction and genotype

This study investigated the relationship in human placenta between polycyclic aromatic hydrocabon (PAH)-DNA adduct levels and two biomarkers of cytochrome P4501A1 (CYP1A1): gene induction evidenced by CYP1A1 mRNA, and a genetic polymorphism, the CYP1A1 MspI RFLP. CYP1A1 codes for an inducible enzyme system that catalyzes the bioactivation of PAHs. Prior research found a high correlation in human lung tissue between CYP1A1 activity and DNA damage from PAHs. The CYP1A1 Mspi RFLP has been linked in some studies to risk of lung cancer. The relationships in human placenta between DNA damage, CYP1A1 activity and genotype have not been well characterized and may be relevant to risks from transplacental PAH exposure. The study cohort consisted of 70 newborns from Krakow, Poland, a city with elevated air pollution, and 90 newborns from nearby Limanowa, an area with lower air pollution but greater indoor coal use. Contrary to results seen previously in lung tissue, CYP1A1 mRNA was not significantly correlated with PAH-DNA adduct levels in the placenta. Smoking (self-reported maternal and infant plasma cotinine) was significantly associated with CYP1A1 mRNA levels (P < 0.01), but not with PAH-DNA adduct levels. Placental PAH-DNA adduct levels were significantly higher in infants with the CYP1A1 MspI restriction site compared with infants without the restriction site (P < 0.01), implicating a genetic factor in inter-individual variation in DNA damage in human placenta. Further studies are needed to determine the relevance of this finding to risk of transplacental carcinogenesis.     

Removal of Sulfate,Phosphate and Colored Substances in Wastewater Effluents using Feldspar

Feldspar, among many natural substances such as termitemount-clay, saw-dust, kaolinite and dolomite, offers asignificant removal ability for sulfate, phosphate, and coloredsubstances. Optimization of experimental parameters such assolution pH and flow rate reveals, that the maximum efficiency forremoval of phosphate, sulfate, and colored substances is about42, 52, and 73% respectively. X-ray diffraction, adsorptionisotherm and recovery studies suggest, that the removal processof anions occurs via ion exchange in conjunction with surfaceadsorption. Furthermore, reaction rate studies indicate thatthe removal of the selected pollutants by feldspar follows first-order kinetics. Although the percent removal, under the optimized conditions, is higher for laboratory prepared solutions, efficiency is a little less for industrial effluentsdue to interferent effects.     

Effect of extraction methods and UHT treatment conditions on the level of isoflavones during soymilk manufacture

The objective of this study was to compare the effect of hot and cold grinding as well as the effect of direct and indirect ultra high temperature (UHT) treatment conditions on the level of isoflavones during the manufacture of soymilk. Soymilks were manufactured from dehulled soybeans by hot grinding or cold grinding processes. After inactivation of lipoxygenase at 85 °C, the resulting slurries were decanted and supernatants were held at 120 °C for 80 s to inactivate the trypsin inhibitor. The decanted soya bases were cooled and subjected to different temperature/time regimes by direct and indirect UHT treatments. Samples were drawn at different points in the processing operation and a reversed phase high performance liquid chromatography method was used to determine the concentration of isoflavones. Results showed that hot grinding caused a higher extraction of isoflavones into the soymilk than the cold-grinding process. However, direct or indirect heating in the UHT process did not significantly influence the concentration of isoflavones.     

A review of transparent insulation systems and the evaluation of payback period for building applications

Research and development of transparent insulation systems (TI-systems) has been ongoing for 20 years with transparent insulation materials (TIMs) used to replace standard opaque insulation materials. TIM not only performs similar functions to opaque insulation, reducing heat losses and controlling indoor temperatures, but allows solar transmittance of more than 50%. With a thickness of less than 20 cm, it can provide a financial return to building occupants when applied to building facades, maximising occupiable and sellable spaces in urban areas, without compromising thermal comfort within buildings.In this review of TI-systems for building applications, drawbacks to previous applications, cost trends, and analysis of the limitation in information from previous studies are discussed. A major drawback in the development of TI-systems identified is the lack of cost information; the payback periods for TI-systems used in previous renovation projects are virtually unknown. Simple payback period calculations were undertaken based on information available from a demonstration project documented by the Solar Heating and Cooling (SHC) Programme of the International Energy Agency (IEA) Task 20 “Solar Energy in Building Renovation”. The calculations indicated an encouraging 5–8-year payback period for this particular case study. It was concluded that the simple payback period calculation may be used for feasibility studies to indicate the time required to recoup investment when installing TI-systems and to provide initial guidance for building designers when evaluating the potential application of TI-systems in their buildings.