Avoiding filter cake cracking: Influence of consolidation on desaturation characteristics

In cake filtration processes with an air-blowing step, cracking is an undesirable phenomenon as it leads to deterioration of the filtration process by highly increasing gas throughput. This leads to higher residual moisture if the pressure difference cannot be maintained and an increase in overall cost. Crack formation can be avoided by compacting the filter cake before desaturation. While this action will make the separation process applicable by highly reducing gas consumption, there are also potential negative effects. Compaction increases filter cake resistance and might therefore slow down desaturation kinetics. Therefore, the authors investigated how the filter cake characteristics governing desaturation change from the nonconsolidated to the consolidated state of the filter cake and compared these findings to the actual dewatering kinetics. The results showed that for the case where cracking could be oppressed, dewatering kinetics of the consolidated cake are actually faster than for the nonconsolidated cake, despite higher resistance of the consolidated cake. Thus, compaction is an appropriate action when dealing with filter cake cracking.     

Development and Validation of an Artificial Mechanical Skin Model for the Study of Interactions between Skin and Microneedles

Microneedles are small needle‐like structures that are almost invisible to the naked eye. They have an immense potential to serve as a valuable tool in many medical applications, such as painless vaccination. Microneedles work by breaking through the stratum corneum, the outermost barrier layer of the skin, and providing a direct path for drug delivery into the skin. A lot of research has been presented over the past two decades on the applications of microneedles, yet the fundamental mechanism of how they interact, pressure, and penetrate the skin in its native state is worth examining further. As such, a major difficulty with understanding the mechanism of microneedle–skin interaction is the lack of an artificial mechanical human skin model to use as a standardized substrate. In this research news, the development of an artificial mechanical skin model based on a thorough mechanical study of fresh human and porcine skin samples is presented. The artificial mechanical skin model can be used to study the mechanical interactions between microneedles and skin, but not diffusion of molecules across skin. This model can assist in improving the performance of microneedles by enhancing the reproducibility of microneedle depth insertions for optimal drug delivery and biosensing.

     

Rapid visualization of the potential residential cost savings from energy storage under time-of-use electric rates

Buildings feature a prominent role in electric grid loading, as they use about 75% of the total electricity generated in the United States and are main drivers of electric peak demand in the summer due to electrically driven air conditioning systems. Energy storage is a key technology that can increase energy cost savings, and add flexibility to the grid. However, cost is an important factor to consider. This study proposes a rapid approach that allows for visualization of potential cost savings by introducing energy storage as a peak load control for residential buildings in California. A combination of EnergyPlus load data generation, Matlab post-processing, and Google Fusion Tables data presentation analyses the potential cost savings when energy storage is implemented and TOU rates are applied. The study presents potential annual cost savings of $420 per home with storage capacities of 24?kWh.     

Synthesis of Co3O4 @ Organo/Polymeric Bentonite Structures as Environmental Photocatalysts and Antibacterial Agents for Enhanced Removal of Methyl Parathion and Pathogenic Bacteria

Two green nanocomposites of Co₃O₄ decorated CTAB/bentonite (Co@CT/BE) and chitosan/bentonite (Co@CH/BE) were synthesized as enhanced and environmental photocatalysts and antibacterial agents. As photocatalysts, the products were applied in the effective oxidation of toxic methyl parathion pesticide (MP) in wastewater under a visible light source. The application of Co@CH/BE (0.02 g) resulted in the complete oxidation of MP (50 mg/L) after 40 min and complete mineralization after 60 min. while the complete oxidation and mineralization of MP (50 mg/L) by Co@CT/BE was recognized after 75 min and 100 min, respectively. The Co@CH/BE composite is of higher activity than Co@CT/BE and can cause complete oxidation for MP at high concentrations up to 100 mg/L after 75 min. The oxidation pathway was illustrated considering the existence of the hydroxyl radicals as the active oxidizing species and the identified secondary organic compounds during the oxidation tests. The detected intermediate converted into end products of CO₂ and inorganic anions of SO₄^?2, NO₃^?, and PO₄^?3 at the final stages of the oxidation processes. As antibacterial agents, the two composites exhibit considerable inhabitation zones of about 20 mm against both the Gram-positive Staphylococcus aureus and Gram-negative bacterium Vibrio Sp. The synthetic Co@CH/BE showed the best antibacterial properties with 200 μg/mL as minimum inhibitory against Staphylococcus aureus.

     

On the Cooling Rate-Microstructure Relationship in Molten Metal Gas Atomization

Metallurgical and Materials Transactions A - Gas atomization is the most used powder production technique since it provides good control on particles shape, surface oxidation and dimension. It is a...     

全球粉末涂料市场

鉴于新冠肺炎疫情的持续流行,对于一年前潜在增长的保守估计需要做出大幅度的调整.第一次封锁解除后,欧洲粉末涂料市场出现了适度改善,但是,随着第二波的限制接踵而来,制造商对未来几个月的恢复预测至多持谨慎态度. 粉末涂料市场与许多市场一样,由于疫情的影响,短期预计会出现下降,但长期的预测是将会趋好.据市场研究公司IRL的Jo...     

3D Bioprinting of Gelatin–Xanthan Gum Composite Hydrogels for Growth of Human Skin Cells

In recent years, bioprinting has attracted much attention as a potential tool for generating complex 3D biological constructs capable of mimicking the native tissue microenvironment and promoting physiologically relevant cell–cell and cell–matrix interactions. The aim of the present study was to develop a crosslinked 3D printable hydrogel based on biocompatible natural polymers, gelatin and xanthan gum at different percentages to be used both as a scaffold for cell growth and as a wound dressing. The CellInk Inkredible 3D printer was used for the 3D printing of hydrogels, and a glutaraldehyde solution was tested for the crosslinking process. We were able to obtain two kinds of printable hydrogels with different porosity, swelling and degradation time. Subsequently, the printed hydrogels were characterized from the point of view of biocompatibility. Our results showed that gelatin/xanthan-gum bioprinted hydrogels were biocompatible materials, as they allowed both human keratinocyte and fibroblast in vitro growth for 14 days. These two bioprintable hydrogels could be also used as a helpful dressing material.