Control strategy for a distributed DC power system with renewable energy

This paper deals with a DC-micro-grid with renewable energy. The proposed method is composed of a gearless wind power generation system, a battery, and DC loads in a DC distribution system. The battery helps to avoid the DC over-voltages by absorbing the power of the permanent magnet synchronous generator (PMSG) during line-fault. In addition, the control schemes presented in this paper including the maximum power point tracking (MPPT) control and a pitch angle control for the gearless wind turbine generator. By means of the proposed method, high-reliable power can be supplied to the DC distribution system during the line-fault and stable power supply from the PMSG can be achieved after line-fault clearing. The effectiveness of the proposed method is examined in a MATLAB/Simulink^® environment.     

Novel mode scrambler for reducing mode dependence in multimode optical waveguides

A novel mode scrambler for multimode optical waveguides is proposed to stabilise branching characteristics against the mode excitation conditio. A 2 × 2 optical star coupler is fabricated using this mode scrambler, and a stable branching ratio is realised with an excess insertion loss of 2.7 dB.     

A 28 μm water-vapor laser interferometer for plasma diagnostics

A high-power CW 27.972 μm water-vapor laser has been developed for interferometric and polarimetric measurements of plasmas. The maximum output power and the power density in the cavity of the laser with 2.0 cm bore and 220 cm length reach 85 mW and 109 μW/cm³, respectively. An interferometer using this laser is constructed and its performance is examined as a study on polarimetric method of magnetic field measurement. Preliminary interferometric experiments are also carried out on a compact toroidal plasma with field-reversal configuration.     

A new control methodology of wind turbine generators for frequency control of power system in isolated island

A wind turbine generator (WTG) system's output is not constant and fluctuates depending on wind conditions. Fluctuating power causes frequency deviations and adverse effects to an isolated power system when large output power from WTG systems is penetrated in the power system. This paper presents an output power control methodology of a WTG for frequency control using a load power estimator. The load power is estimated by a disturbance observer, and the output power command of the WTG is determined according to the estimated load. Besides, the WTG can also be controlled during wind turbulence since the output power command is determined by considering wind conditions. The reduction of the power system frequency deviation by using the WTG can be achieved by the proposed method. The effectiveness of the proposed method is validated by numerical simulations. Copyright © 2010 John Wiley & Sons, Ltd.     

DNA microarray analysis suggests that zinc pyrithione causes iron starvation to the yeast Saccharomyces cerevisiae

Zinc pyrithione has been used in anti-dandruff shampoos and in anti-fouling paint on ships. However, little is known of its mode of action. We characterized the effects of sub-lethal concentrations of zinc pyrithione (Zpt) on Saccharomyces cerevisiae using DNA microarrays. The majority of the strongly upregulated genes are related to iron transport, and many of the strongly downregulated genes are related to the biosynthesis of cytochrome (heme). These data suggest that Zpt induces severe iron starvation. To confirm the DNA microarray data, we supplemented cultures containing Zpt with iron, and the growth of the yeast was restored significantly. From these results, we propose that the principal toxicity of zinc pyrithione arises from iron starvation.     

Measurements of thermal-neutron capture cross-section of Cesium-135 by applying mass spectrometry

ABSTRACT

The thermal-neutron capture cross-section (σ₀) and resonance integral (I₀) were measured for the ¹³⁵Cs(n,γ)¹³⁶Cs reaction by an activation method and mass spectrometry. Because of difficulty in the preparation of pure ¹³⁵Cs samples, we used ¹³⁵Cs contained as an impurity in a normally available ¹³⁷Cs standard solution. An isotope ratio of ¹³⁵Cs and ¹³⁷Cs in a standard ¹³⁷Cs solution was measured by mass spectrometry to quantify ¹³⁵Cs. Cesium-135 impurity along with the ¹³⁷Cs standard solution was irradiated at the hydraulic conveyer of the research reactor in the Institute for Integral Radiation and Nuclear Science, Kyoto University. Wires of Co/Al and Au/Al alloys were used as neutron monitors to measure thermal-neutron fluxes and epi-thermal Westcott’s indices at an irradiation position. A gadolinium filter was used to measure the σ₀, and a value of 0.133 eV was taken as the cut-off energy. Gamma-ray spectroscopy was used to measure induced activities of ¹³⁷Cs, ¹³⁶Cs and monitor wires. On the basis of Westcott’s convention, the σ₀ and I₀ values were derived as 8.57 ± 0.25 barn, and 45.3 ± 3.2 barn, respectively. The value of σ₀ obtained in the present study agreed within the limits of uncertainties with the past-reported value of 8.3 ± 0.3 barn.     

Quantitative measurement of mRNA at different loci within an individual living cell

Asymmetric localizations of cellular proteins and mRNAs are important for cell functions such as division, differentiation and development. The localization of specific mRNA generates cell polarity by controlling the translation sites of specific proteins and thereby restricting their locations to appropriate cellular regions. We have previously reported a novel method based on atomic force microscopy (AFM) for examining gene expression in a single living cell without killing or destroying it. An AFM tip was inserted into a living cell to extract mRNAs, which were analyzed after multiplication by RT-PCR and quantitative PCR. By applying this method, in this study we performed quantitative measurement of mRNA at different loci within individual living cells.     

Sintering Kinetics at Isothermal Shrinkage: Effect of Specific Surface Area on the Initial Sintering Stage of Fine Zirconia Powder

The isothermal shrinkage behaviors of fine zirconia powders (containing 2.8–2.9 mol% Y₂O₃) with specific surface areas of about 6 and 16 m²/g were investigated to clarify the effect of specific surface area on the initial sintering stage. The shrinkage of powder compact was measured under constant temperatures in the range of 1000°–1100°C. The increase in specific surface area enhanced the densification rate with increasing temperature. The values of activation energy ( Q ) and frequency-factor term (β₀) of diffusion at initial sintering were estimated by applying the sintering-rate equation to the isothermal shrinkage data. The Q of diffusion changes little but the β₀ increases with the increase in specific surface area. It is therefore concluded that the increase in the specific surface area of fine zirconia powder enhances the shrinkage rate because of an increase in the β₀ at the initial stage of sintering.     

Sintering Kinetics at Isothermal Shrinkage: II, Effect of Y2O3 Concentration on the Initial Sintering Stage of Fine Zirconia Powder

The shrinkage behavior of fine zirconia powders containing 2.9 and 7.8 mol% Y₂O₃ was investigated to clarify the effect of Y₂O₃ concentration on the initial sintering stage. The shrinkage of powder compact was measured under both conditions of constant rates of heating (CRH) and constant temperatures. CRH measurements revealed that when the Y₂O₃ concentration of fine zirconia powder increased, the starting temperature of shrinkage shifted to a high temperature. Isothermal shrinkage measurements revealed that the increase in Y₂O₃ concentration causes the shrinkage rate to decrease. The values of activation energy ( Q ) and frequency-factor term (β₀) of diffusion at initial sintering were estimated by applying the sintering-rate equation to the isothermal shrinkage data. When the Y₂O₃ concentration increases, both Q and β₀ of diffusion increase. It is, therefore, concluded that the increase in Y₂O₃ concentration of fine zirconia powder decreases the shrinkage rate because of increasing Q of diffusion at the initial stage of sintering.     

Solid-state characterization of polyethylene reactor powders and their structural changes upon annealing

Polyethylene reactor powders prepared under different conditions were characterized using transmission electron microscopy, ¹H nuclear magnetic resonance and X-ray diffraction techniques. The molecular weight of the polyethylene reactor powders was around 1 × 10⁵. A unique domain morphology, quite different from the usual melt- or solution-crystallized lamellar structure, was observed, independent of polymerization temperature (T_poly). Annealing of reactor powders caused the aggregation of these crystalline domains, due to the significant molecular motion of the amorphous chains, before melting. The critical temperature was 20 °C higher than each T_poly, and corresponded to the temperature at the active catalyst site producing the chain growth. The morphologies of powders prepared at the lower T_poly contained smaller crystals that exhibited a constrained monoclinic form. In contrast, only usual orthorhombic crystals of larger size were found within the powder prepared at the higher T_poly. These results suggest that the competitive processes of chain propagation and crystal growth upon polymerization may lead to unique variations of the crystalline and amorphous phases, but with similar intermediate components in the phase that connects them.