Preparation and properties of biocomposites composed of glycerol‐based epoxy resins,tannic acid,and wood flour

After polyglycerol polyglycidyl ether (PGPE) and glycerol polyglycidyl ether (GPE) were mixed with tannic acid (TA) in ethanol and without solvent at epoxy/hydroxyl ratio 1/1, the obtained GPE‐TA and PGPE‐TA solutions were mixed with wood flour (WF), prepolymerized at 50°C, and subsequently compressed at 160°C for 3 h to give GPE‐TA/WF and PGPE‐TA/WF biocomposites with WF content 50–70 wt %, respectively. The storage moduli of the biocomposites in the rubbery state at more than 80°C were much higher than that of the control cured resins. The PGPE‐TA/WF composites had higher tensile modulus and rather lower tensile strength than PGPE‐TA. On the other hand, both the tensile modulus and strength of GPE‐TA/WF were much higher than those of GPE‐TA (2.4 GPa and 37 MPa). Those values of GPE‐TA/WF increased with WF content, became maximal values (5.1 GPa and 51 MPa) at WF content 60 wt %, and were lowered at 70 wt %. FE‐SEM analysis of the fractured surface of the biocomposites revealed that WF is tightly incorporated into the crosslinked epoxy resins. As a result of optimization of the epoxy/hydroxyl molar ratio for GPE‐TA/WF composite with WF content 60 wt %, the composite prepared at the ratio of 1.0/0.8 showed the highest tensile modulus and strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Palladium‐Catalyzed Arylation of Methylene‐Bridged Polyarenes: Synthesis and Structures of 9‐Arylfluorene Derivatives

In the presence of a catalytic system comprised of palladium(II) acetate and tricyclohexylphosphine, the reaction of fluorene with haloarenes generated 9‐arylfluorenes in good to excellent yields. The scope and limitations of the coupling reaction were investigated. This synthetic protocol is more efficient than conventional methods. A wide range of functional groups, including alkyl, alkoxy, ester, and nitrile, can tolerate the reaction conditions herein. Sterically congested haloarenes also gave satisfactory results. Furthermore, this synthetic method is utilized to prepare 9,9‐diarylfluorenes and tetraarylindenofluorene. Depending on the reaction conditions, the arylation of bowl‐shaped sumanene gave monoarylated sumanene either as the sole product or with another diaryl‐substituted product.     

In situ infrared microspectroscopy of approximately 850 million-year-old prokaryotic fossils

In situ infrared (IR) and Raman microspectroscopy have been conducted on Neoproterozoic, organic-walled microfossils (prokaryotic fossils) in doubly polished, petrographic thin sections in order to detect their spectral signatures. The microfossils are very well preserved and occur in black chert from the approximately 850 million-year-old Bitter Springs Formation, Northern Territory, Australia. Raman microspectroscopy on two species of microfossils, one a filament and the other a coccoid, shows disordered peaks (D peak, 1340 cm(-1)) and graphite peaks (G peak, 1600 cm(-1)), indicating that they consist of disordered carbonaceous materials. IR micro-mapping results of the filament reveal that the distributions of peak heights at 2920 cm(-1) (aliphatic CH(2)), 1585 cm(-1) (aromatic C-C), and 1370 cm(-1) (aliphatic CH(3)) match the shape of the filamentous microfossil. These results suggest that IR microspectroscopy can be used for in situ characterization of organic polar signatures that morphologically indicate microfossils embedded in chert by using doubly-polished rock (petrographic) thin section samples. Further, these methods can be applied to controversial microfossil-like structures to test their biogenic nature.     

Single-walled carbon nanotube growth from highly activated metal nanoparticles

We demonstrate that any metal, even gold, silver, and copper, can act as a catalyst for SWCNT synthesis in chemical vapor deposition (CVD). Metal nanoparticles 3 nm or less in diameter, introduced into CVD ambience immediately after heat treatment at 800-950 degrees C in air, produce SWCNTs. The activation method is effective for copper and various noble metals as well as for iron-family elements. This implies that any metal particle may produce SWCNTs when its size becomes 1-3 nm. In other words, carbon atoms can form SWCNTs in a self-assembling fashion on nanoparticles without the specific functions of iron-family elements.     

Graphene growth on a Pt(111) substrate by surface segregation and precipitation

We report on the fabrication of a sizable graphene sheet on a carbon-doped Pt(111) substrate through surface segregation and precipitation. Scanning Auger electron spectroscopy (AES) reveals that the graphene covered more than 98% of the substrate surface. Our graphene consists of single-layer graphene across the substrate with fractions of several micrometer wide bi- and tri-layer graphene islands. We also show that the number of graphene layers can be precisely determined by analyzing AES data. While Raman spectroscopy is usually used to study graphene on SiO?, we show that AES is a powerful tool to characterize graphene grown on metal substrates.     

通过功率MOSFET的顶面温度估算结点温度

通常,MOSFET数据手册中提供的结点温度数据只限于结到引脚和结到环境之间的热阻。虽然可根据定制条件使用一些工具来实现更精确的热仿真,但有时只需要时间来运行仿真就可以了。     

Film formation from cationic electropaint systems containing resins with different glass transition temperature

Some phenomena in the deposition process of electropainting have not been well elucidated till now. In this paper, to investigate an influence of glass transition temperature (T_g) on film formation, the deposited film was observed with an atomic force microscope and the electrochemistry was investigated, using two kinds of cationic acrylate resin with different T_g (methyl methacrylate system (MMAs): T_g=70°C, and methyl acrylate system (MAs): T_g=5°C). Electrodeposition was performed under constant voltage or current condition.

At constant voltage, the deposition behavior in the two resin systems differed extremely. The MMAs, the resin with high T_g, produced a high resistance film. The MAs, the resin with low T_g, was deposited forming a film at a voltage lower than 20 V. At constant current, the film formation did not result in a rise in voltage. It behaved like a conductive film. When the resin with high T_g was used, particulate deposits were observed by AFM even in the induction period. The resin with low T_g formed flat deposits. These results suggest that paint deposition is initiated once electrolysis of water starts. In addition, there are two types of film formation on the cationic electropainting: high resistance film formation for the resin with high T_g, and ion-permeable film formation for the resin with low T_g. In both cases, film growth occurs at the film/bulk solution interface.     

Cost-Effective Low Vt Ni-FUSI CMOS on SiON by Means of Al Implant (pMOS) and Yb+P Coimplant (nMOS)

Low V_t Ni fully silicided (FUSI) devices are demonstrated making use of Al implantation for pMOS and Yb or Yb+P implantation for nMOS combined with Ni-silicide phase engineering. When Yb(+P) and Al implantation are followed by a high temperature anneal, significant segregation of Yb or Al toward the Ni-FUSI/SiON interface is observed and large Vt shifts of 450 mV (330 mV) and 200 mV are obtained for nMOS NiSi FUSI/SiON devices and pMOS Ni-rich FUSI/SiON devices, respectively, as compared to the undoped reference devices. The Vt shifts are preserved down to the shortest gate lengths. For both Al and Yb, the V_t shifts are explained by the dopants reacting with and modifying the dielectric. Thus, the low V_t dual implantation approach proposed achieves a low-cost "dual dielectric" implementation without the need of dual deposition of dielectrics or capping layers. In the case of Yb implantation followed by a high temperature anneal, a significant reduction in the inversion dielectric thickness is observed, indicating that the reaction between Yb and SiON results in the formation of a high-k dielectric. The Yb diffusion and reaction at the interface can be engineered using a P coimplant.     

Development of multicomponent vaporization/condensation model for a reactor safety analysis code SIMMER-III: Extended verification using multi-bubble condensation experiment

Complex phenomena such as phase transitions and heat transfers in multiphase, multicomponent flows were modeled in the fluid-dynamics portion of SIMMER-III, which was developed to appropriately assess core disruptive accidents (CDAs) in liquid–metal fast reactors (LMFRs). A new multicomponent vaporization/condensation (V/C) model was developed and introduced to SIMMER-III by the authors. In the present study, a new series of multi-bubble condensation experiments was performed to demonstrate that SIMMER-III with the present V/C model is practically applicable to multicomponent, multiphase flow systems with phase transition. In the experiments, bubble diameters and void fractions were quantified from visualization images using original image-processing techniques. Comparing SIMMER-III predictions with experimental data, it was confirmed that SIMMER-III with the proposed V/C model could suitably represent the effects of noncondensable components on the condensation process in multi-bubble systems. This work has improved the reliability of SIMMER-III with regard to multicomponent phase-transition phenomena.     

Field experiments on energy consumption and thermal comfort in the office environment controlled by occupants’ requirements from PC terminal

The thermal environment in an office is not always optimal from the viewpoint of energy-conservation and occupants’ comfort. The main reason is that air-conditioning systems are controlled without taking the occupants’ needs into account. In this study, we would like to propose a new system to control air-conditioning systems, lighting systems, etc. via occupants’ requests. This system collects occupants’ requests from their own personal computers and controls the air-conditioning system with logic that balances the needs of occupants and energy consumption. The control logic is referred to as “Logic for Building a Consensus” and can be adjusted according to operating strategies such as energy-saving or occupants’ satisfaction with their environment. Moreover, the variety of feedback motivates occupants to cooperate with energy-saving efforts.

An interactive system to use occupants’ requests for controlling the air-conditioning system and providing a variety of feedback was developed. A series of cooling experiments were conducted in an open-plan office where about 50 people worked. The results show that this interactive system could save 20% more energy compared with controlling an air-conditioning system at a constant 26 °C.