Development of three-dimensional electric field analysis by segment arrangement based on a charge simulation method

This paper describes the development of three-dimensional electric field analysis by using the so-called segment method which enables the electric field to be calculated with high accuracy and with enhanced efficiency, for high-voltage apparatus. In the segment method, electrode configuration of high-voltage apparatus is simulated by small components which are called segments and by the arrangement of several kinds of such segments. In this calculation, the charge simulation method is used which is suitable for segment application. As basic segments, spherical, cylindrical and ring segments are used and in addition to these, as subsegments, disc and elbow segments are adopted for good simulation of the total electrode configuration. In this paper, the fundamental construction and arrangement parameter of segments were discussed. Moreover, the segment method was applied to an actual high-voltage apparatus and the calculation accuracy was discussed. It was clarified that the segment method has sufficient calculation accuracy and is a very efficient means for three-dimensional electric field analysis.     

Prediction of heat exchanger performance by the thermal network method (Improvement of an evaporator's performance and restraining air flow bypass by adjusting the refrigerant‐flow path pattern)

This paper presents the influence of latent heat load by changing the relative humidity of air flow distribution in the super‐heated gas region in an evaporator and the effect of the refrigerant flow path pattern. To estimate the influence, we applied the thermal network method that can consider refrigerant quality distribution in the heat exchanger. If the super‐heated gas region spreads to the upper wind row, humid air goes through the heat exchanger without drying, called “air flow bypass.” To suppress this phenomenon and simultaneously obtain the best performance, we chose an optimum path pattern on the basis of this method. As a result, the prediction shows that performance of the evaporator is recovered 5% for a simple 2‐row 2‐path heat exchanger when 40% of the unbalance of air flow rate occurs. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20302     

Hydrogen uptake of reduced graphene oxide and graphene sheets decorated with Fe nanoclusters

Graphene oxide (GO) has been prepared by employing modified Staudenmaier's method through thermal exfoliation of graphite oxide. High pressure hydrogen sorption isotherms up to 50 bar of GO, reduced by thermal reduction (TR-GO), chemical reduction (CR-GO) and graphene sheets decorated with Fe nanoclusters (Fe-GS) have been investigated. Thermal reduction of GO at 623 K under high vacuum yields TR-GO. Chemical reduction of GO using hydrazine forms CR-GO. Fe-GS was synthesized through arc-discharge between the ends of two graphite rods with one rod carrying Fe nanoparticles. The surface areas of these graphene samples were determined from the nitrogen adsorption isotherm employing Brunauer, Emmett and Teller (BET) method. Kelvin's equation was used to determine the pore size distribution of all graphene based samples. Hydrogen pressure-composition isotherms (PCI) were determined at 300 K and at 77 K, between 0.1 and 50 bar. Further, in this paper, we present a comparative adsorption isotherm analysis of hydrogen and helium on TR-GO. This reveals that the volume of hydrogen and helium adsorbed by TR-GO is nearly equal. The similar uptake volume determined for both hydrogen and helium indicates the possibility of monolayer adsorption of hydrogen and also nearly similar binding energy between TR-GO and H₂/He.     

Real-time monitoring of luciferase-tagged Cronobacter sakazakii in reconstituted infant milk formula

The aim of this study was to examine the potential of using a lux-tagged Cronobacter sakazakii strain to monitor growth of the bacterium in various liquids. C. sakazakii was transformed with plasmid p16S lux, and integration of the plasmid at the desired site on the chromosome was confirmed by PCR. The growth of the lux-tagged strain was similar to that of the non-lux-tagged strain, and the integrated plasmid was stable when cells were cultured in the absence of antibiotic. Growth of the lux-tagged strain was monitored in real time in Luria-Bertani broth, skim milk, and infant milk formula by using both the Luminoskan luminometer and the Xenogen IVIS imager. Bioluminescence could be detected when the lux-tagged strain was cocultured with other bacteria. The effect of monocaprylin and nisin on the growth of C. sakazakii in milk was monitored by measuring bioluminescence. In conclusion, growth of a lux-tagged C. sakazakii can be monitored in real time in both clear and opaque liquids by measuring bioluminescence. lux-tagged C. sakazakii strains could be potentially used in high-throughput assays to monitor the effects of various infant milk formula compositions on growth of the bacterium.     

Existence states of deuterium irradiated into LiAlO2

The existence states of deuterium in LiAlO₂ were analyzed by in situ IR absorption spectroscopy during irradiation with 3 keV at room temperature. Multiple IR absorption peaks that were related to O-D stretching vibrations were observed, mainly at 2650 cm⁻¹ (O-D_α), 2600 cm⁻¹ (O-D_β), and 2500 cm⁻¹ (O-D_γ). The O-D_α was assigned to the surface O-D. The O-D_β and O-D_γ were interpreted as two distinct O-D states for three candidates: O-D of substitutional D⁺ for Li⁺; O-D of substitutional D⁺ for Al³⁺; and O-D of interstitial D⁺. O-D_β was the dominant O-D state for deuterium irradiated into LiAlO₂, and had higher stability than O-D_γ. Heating after ion irradiation led to the desorption of D₂ and an increase in the intensity of O-D_β, which implies that some of the deuterium irradiated into LiAlO₂ exists in non-O-D states, such as D⁻ captured by F centers.     

Prediction of the capacity of a heat exchanger by a thermal network method: Modified effective specific heat model considering the influence of static pressure distributions of refrigerants

In this paper, we proposed a method to predict the capacity of a heat exchanger by considering static pressure distributions of refrigerants. The thermal network method was modified by adding an equivalent heat generation term into a heat balance equation that was connected with calculated 1D static pressure distributions of refrigerants. An experiment was performed with a heat exchanger having two rows and two passes to verify the accuracy of the proposed method. The result showed the error of the predicted capacity to be less than 1% for an evaporator and less than 2% for a condenser. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(5): 376–390, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10039     

PIV measurement and turbulence scale in turbulent combustion

We have investigated turbulent combustion by PIV (Particle Image Velocimetry) technique. Comparing with LDV data, the validity of PIV measurements has been confirmed. Particularly, the conditions of sampling number and spatial resolution have been shown to yield reliable data using PIV. Based on the velocity fields in cold flow and combustion, the interaction between flame and flow has been discussed. It was observed that the flow field is changed by combustion and the turbulence is reduced. In order to determine statistical quantities such as mean velocity and RMS of velocity fluctuation, a sampling number of 1000 is needed. Moreover, the velocity correlation coefficient was evaluated to obtain the integral length scale of the flow. For both cold flow and combustion, the PIV estimated scale is very close to that of LDV based on the assumption of Taylor's hypothesis. As a result, the spatial resolution in this study is about 6 times smaller than the integral length scale. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(7): 501–512, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20129     

A numerical method for natural convection and heat conduction around and in a horizontal circular pipe

Natural convection around a horizontal circular pipe coupled with heat conduction in the solid structure is numerically investigated using a preconditioning method for solving incompressible and compressible Navier–Stokes equations. In this method, fundamental equations are completely reduced to an equation of heat conduction when the flow field is static (zero velocity). Therefore, not only compressible flows but also very slow flows such as natural convection in a flow field and heat conduction in a static field can be simultaneously calculated using the same computational algorithm. In this study, we first calculated the compressible flow around a NACA0012 airfoil with conduction in the airfoil and then simulated natural convections around a horizontal circular pipe with a different heat conductivity. Finally, we numerically investigated the effect of heat conductivity of the pipe on natural convection.