Properties of aqueous solutions of several salts of α,ω-alkanediol disulfates

Several salts of α,ω-sulfates, MO₃SO(CH₂)_n OSO₃M(n=12, 14, 16, 18, and M=Li, Na, and K) were prepared from the corresponding α,ω-alkane diols. The Krafft points of these α,ω-sulfates with common counterion as estimated by electroconductivity measurements increased with the increase of the hydrocarbon chain length, and the effect of the counterions on the Krafft points of the α,ω-sulfates with the same hydrocarbon chain length was in the order : Li<Na<K. Solutions of the α,ω-sulfates, except disodium dodecanediol disulfate, showed two break points corresponding to the first and second critical micelle concentration in each plot of the electroconductivity as a function of the concentration. The existence of the second break point suggested that another aggregation of rearrangement of the existing aggregates occurs in α,ω-sulfate solutions in addition to the usual micelle formation. The first and second break points of α,ω-sulfates with sodium counterion decreased logarithmically with increasing total number of methylene groups. The relationships were given as follows: log(first break point)=−0.138Nc−0.095; log(second break point)=−0.104Nc−0.251. The effect of the counterions upon the break points of α,ω-sulfates with the same hydrocarbon chain length was in accordance with their positions in the lyotropic series.     

Network formation and swelling behavior of photosensitive poly(vinyl alcohol) gels prepared by photogenerated crosslinking

Poly (vinyl alcohol) with pendent styrylpyridinium groups (SbQ) is insolubilized by photoirradiation. An association takes place in SbQ groups. The association of polymer chains becomes marked with increasing the number of SbQ groups. Mainly intermolecular crosslinks were formed. Transparent and homogeneous macrogels consisting of several intermolecular crosslinks are obtained. The proportion of the free water to the bound water in PVA-SbQ gels was 3.3?2.9 despite of the large change in conversion of photodimerization of SbQ groups, x=0.27?0.58. The water uptake after swelling of the gels in water increased 6–27 times compared to the original weight at pH=7. The higher the degree of photocrosslinking, the lower was the degree of swelling. The water diffusion coefficients, D, were (2.2?5.8) × 10^?5 cm² S^?1 for a 88% saponified PVA with 1 . 3 mol% SbQ groups. The volume of the gel increased discontinuously about 10-fold for the 99% saponified PVA with 0 . 096 mol% SbQ and 51% water (49% acetone). The acetone concentration at the transition decreased with increasing the degree of saponification of the PVA.     

Dynamic moduli for short fiber-CR composites

The dynamic moduli, E′ and E″, and tan δ for nylon–CR and PET–CR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed two dispersion peaks for nylon–CR composite. The peak at ?28°C corresponded to the main dispersion of CR and the peak at 100°C to the α-dispersion of nylon 6. For a PET-CR composite, in addition to the individual dispersion of CR and PET, a small and broad peak was observed at about 90°C. The angular dependence of E′ indicated that the short fibers assumed good orientation. The storage modulus for the composites was given by the parallel model as E′ = V_f′E_f + V_mE′_m., where E′_c, E′_f and E′_m were the storage modulus for the composite, fiber, and matrix and V_f and V_m were the volume fraction of fiber and matrix, respectively. In the transverse direction of fiber, the peak values of tan δ at ?28°C were given by the following equation; tan δ_c = tan δ_m ? δV_f, where tan δ_c and tan δ_m are the loss tangent for the composite and matrix, respectively, and α is coefficient depending on fiber type. The results indicated that a region with strong interaction was formed between fibers and CR matrix.     

An ergonomics study of thumb movements on smartphone touch screen

This study investigated the relationships between thumb muscle activity and thumb operating tasks on a smartphone touch screen with one-hand posture. Six muscles in the right thumb and forearm were targeted in this study, namely adductor pollicis, flexor pollicis brevis, abductor pollicis brevis (APB), abductor pollicis longus, first dorsal interosseous (FDI) and extensor digitorum. The performance measures showed that the thumb developed fatigue rapidly when tapping on smaller buttons (diameter: 9 mm compared with 3 mm), and moved more slowly in flexion–extension than in adduction–abduction orientation. Meanwhile, the electromyography and perceived exertion values of FDI significantly increased in small button and flexion–extension tasks, while those of APB were greater in the adduction–abduction task. This study reveals that muscle effort among thumb muscles on a touch screen smartphone varies according to the task, and suggests that the use of small touch buttons should be minimised for better thumb performance.     

New method for selective growth of diamonds by microwave plasma chemical vapour deposition

Selective nucleation and deposition of diamonds were achieved on an SiO₂-patterned Si substrate. The substrate was pre-treated with an electric field in plasma to introduce diamond nuclei. This treatment did not affect the SiO₂ area. Consequently, diamonds grew only on the area where Si was exposed under the conventional conditions of diamond growth. The maximum nucleation density on the area of SiO₂was about 5 × 10⁷ cm⁻². The ratio of the selectivity was 2 × 10² or higher. This process will be useful and very promising for manufacturing diamond electronic devices.     

Evaluation for the curing characteristics of phenolic molding compounds by rockwell hardness test at an elevated temperature

Rockwell hardness measurement at an elevated temperature has been proposed as an evaluation method for the curing characteristics of thermosetting molding compounds. This method is convenient and has a high accuracy over a wide range of curing, Using a cone indenter, the following advantages are brought about: a good correspondence with acetone extraction test, in showing the degree of cure of the internal part of a molding rather than that of the skin layer, and a higher sensitivity in measuring higher degrees of cure. On examining curing behavior of commercial phenolic molding compounds by this method, an inflection point was observed on a plot of the hardness vs log curing time. This critical point has been called “the minimum cure time”, beyond which the molding exhibits good physical properties.     

New multicolor and rewritable holographic polymer film for three‐dimensional holographic display

We have developed a new multicolor holographic polymer film. Our holographic polymer film contains 3‐[(2,4,6‐trichloro)azo]‐9H‐carbazole‐9‐ethanol (A‐1) and poly(methyl methacrylate). The holographic polymer film can be recorded with a holographic image without applying an external electric field. The diffraction efficiency was 57% at A‐1 with a 20 wt% of dope ratio. The writable holographic image writing for the holographic polymer film step used the silver halide photographic emulsion master plate 532‐nm laser beam under the nonelectric field. After the copy hologram is formed, our holographic polymer film can be displayed in red and green holographic images. Even though our holographic polymer film is rewritten over 200 times, the diffraction efficiency does not fall. As the holographic polymer film is manufactured using roll‐to‐roll techniques, although still in a laboratory scale in this study, it has a strong possibility of being manufactured in larger sizes with lower cost.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Study on stiffness visualization and safety control based on will-consensus building for tele-palpation robot system

This paper proposes a method for visualizing the stiffness of a soft object in a palpation-support information system by the teleoperation of a robot hand. It is important that a palpation system display a body’s shape and stiffness. In our method, the stiffness of the contact area between the soft object and the robot finger is estimated by a recursive least-squares method with forgetting factor that uses an impedance dynamics model. With the estimated stiffness and direction of contact force, we calculate the scalar parameter for visualization of stiffness. Moreover, we propose a safety control method for the palpation system, which is part of a tele-control method based on will-consensus building. The system configuration, estimated algorithm, and experimental results are presented.