Schottky barrier heights of contact metals to p-type ZnSe

Schottky barrier heights (SBHs) of a variety of metals (In, Cd, Nb, Ti, W, Cu, Ag, Au, Ni, Pt, and Se) contacting to p-ZnSe grown by a molecular beam epitaxy method were determined by analyzing capacitance-voltage (C-V) and/or current density-voltage (J-V) curves. The SBH values of the Au and Ni contacts were determined from intersections of straight lines of the C⁻²-V curves to be 1.23 and 1.13 eV, respectively. The J-V calculations provided a large SBH value of 1.2 ± 0.1 eV for a variety of metals, indicating that the Fermi-level could be pinned at the contact interface. Reduction of the SBH values to a level lower than 0.4 eV and/or increase of doping concentrations to a level higher than 10²⁰ cm⁻³ are essential to obtain an ohmic contact with contact resistivity of around 10⁻³ Ω·cm².     

Implicit integration and consistent tangent modulus of a time‐dependent non‐unified constitutive model

This paper describes the implicit integration and consistent tangent modulus of an inelastic constitutive model with transient and steady strain rates, both of which are time‐ and temperature‐dependent; the transient rate is influenced by the evolution of back stress decomposed into parts, while the steady rate depends only on applied stress and temperature. Such a non‐unified model is useful for high‐temperature structural analysis and is practical owing to the ease in determining material constants. The implicit integration is shown to result in two scalar‐valued coupled equations, and the consistent tangent modulus is derived in a quite versatile form by introducing a set of fourth‐rank constitutive parameters into the discretized evolution rule of back stress. The constitutive model is, then, implemented in a finite element program and applied to a lead‐free solder joint analysis. It is demonstrated that the implicit integration is very accurate if the multilinear kinematic hardening model of Ohno and Wang is employed, and that the consistent tangent modulus certainly affords quadratic convergence to the Newton–Raphson iteration in solving nodal force equilibrium equations. Copyright © 2003 John Wiley & Sons, Ltd.     

A Tuning Circuit with Two Half-Wave Distributed Junctions for All-NbN SIS Mixers

A novel broadband tuning circuit composed of two low-current-density half-wave NbN/MgO/NbN tunnel junctions connected by a half-wave NbN/MgO/NbN microstrip line has been successfully tested in a quasi-optical mixer at frequencies above 700 GHz. The circuit had a designed center frequency of 870 GHz, was integrated in a center-fed twin-slot antenna, and was fed via a quarter-wave impedance transformer. Heterodyne measurments showed double-side-band receiver noise temperatures equivalent to 6-9 quanta from 675 to 810 GHz for a mixer with a current density of 6.7 kA/cm². The RF bandwidth was broader than that of a conventional mixer using a full-wave junction with the same current density.     

A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

Changes in the thermomechanical behavior of epoxy glasses under the state of strain aging

Changes in thermomechanical behavior with structural relaxation taking place in epoxy glasses were studied. Differential scanning calorimetry measurements and thermostimulated strain recovery tests were performed for specimens deformed and then aged under fixed strain. In the course of heating, the specimens started to absorb thermal energy, whereas plastic strain was still stable. At higher temperatures, plastic strain started recovery, which was accompanied by exothermic behavior of the specimen. With an increase in the aging duration, the endothermic peak signified and moved to a higher temperature. These results indicated that the longer the aging duration was, the harder the plastic strain and strain energy were frozen in the glassy structure. This freeze‐strain phenomenon was observed for crosslinked epoxy glass, as well as polymeric glasses with linear molecular structures, aged under strain. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Spontaneous hemorrhage of an adrenal cortical adenoma causing Cushing''s syndrome

A modified surgical splint for Le Fort I osteotomies with transverse expansion is presented. The splint is made of a transpalatal stainless steel bar with acrylic abutment against the palatal surface of the molar and bicuspid tooth. It is rigid and renders excellent retention. It causes minimal patient discomfort, and oral hygiene is hardly compromised.     

Polarization-controlled single-mode VCSEL

Relative intensity noise (RIN) in a vertical-cavity surface-emitting laser (VCSEL) was greatly reduced through the use of polarization control to eliminate competition between two orthogonal polarization states by ensuring there was only one polarization state. Polarization was stable with optical feedback of up to 10%. Polarization control was achieved by inducing a small loss anisotropy in fundamental transversal mode VCSEL's. Anisotropic post structures, such as a rectangular post, an oblique post, or a zigzag-sidewall post, were found to be effective in creating loss anisotropy without serious degradation of other VCSEL characteristics such as light-output power or beam profile     

Room temperature pulsed operation of 1.5 μm GaInAsP/InPvertical-cavity surface-emitting laser

Room-temperature pulsed operation of a GaInAsP/InP vertical-cavity surface-emitting laser diode (VCSELD) with an emission wavelength near 1.55 μm is reported. A double heterostructure with a 34-pair GaInAsP (λ_g=1.4 μm)/InP distributed Bragg reflector (DBR) was grown by metalorganic chemical vapor deposition (MOCVD). The measured reflectivity of the semiconductor DBR is over 97% and threshold current is 260 mA for a 40-μmφ device with a 0.88-μm-thick active layer. Threshold current density is as low as 21 kA/cm² at room temperature     

Advanced concepts in electric vehicle design

In 1994, the Eco-Vehicle Project was begun to develop an electric vehicle (EV) using a ground-up design approach that incorporates unique designs specific to an EV. The Eco-Vehicle will be a high-performance, but ultrasmall, battery-powered vehicle. New designs for the Eco-Vehicle include an in-wheel motor drive system, a hollow load floor which will house the batteries, and a new battery management system. The Eco-Vehicle may also utilize other advanced concepts suitable especially for EVs, including solar panels for battery charging and intelligent crash avoidance and guidance systems     

Transformation and fragmentation behavior of molten metal drop in sodium pool

In order to clarify the fragmentation mechanism of a metallic alloy (U–Pu–Zr) fuel on liquid phase formed by metallurgical reactions (liquefaction temperature = 650 °C), which is important in evaluating the sequence of core disruptive accidents for metallic fuel fast reactors, a series of experiments was carried out using molten aluminum (melting point = 660 °C) and sodium mainly under the condition that the boiling of sodium does not occur. When the instantaneous contact interface temperature (T_i) between molten aluminum drop and sodium is lower than the boiling point of sodium (T_c,bp), the molten aluminum drop can be fragmented and the mass median diameter (D_m) of aluminum fragments becomes small with increasing T_i. When T_i is roughly equivalent to or higher than T_c,bp, the fragmentation of aluminum drop is promoted by thermal interaction caused by the boiling of sodium on the surface of the drop. Furthermore, even under the condition that the boiling of sodium does not occur and the solid crust is formed on the surface of the drop, it is confirmed from an analytical evaluation that the thermal fragmentation of molten aluminum drop with solid crust has a potential to be caused by the transient pressurization within the melt confined by the crust. These results indicate the possibility that the metallic alloy fuel on liquid phase formed by the metallurgical reactions can be fragmented without occurring the boiling of sodium on the surface of the melt.