A prioritization method for replacement of water mains using rank aggregation

Pipe breaks in municipal water distribution networks may cause serious damage economically and socially. Existing methods for replacement scheduling of pipes do not provide practical indicators for replacing an individual deteriorated pipe. This work formulates the selection problem as the decision of preference ordering or ranking and proposes a bipartite ranking-based approach. The suggested approach also considers loss from broken pipes in terms of the costs associated with broken water main and its repair. We use rank aggregation method to integrate multiple ranks into replacement order of water mains. The suggested framework prioritizes current pipe sections for replacement based on the aggregated ranks. Multiple ranks given by the reliability of water pipe sections are aggregated and a cost effective policy for pipe replacement is derived.     

Low-temperature fabrication of TiO<Subscript>2</Subscript> film on flexible substrate by atmospheric roll-to-roll CVD

Titanium dioxide (TiO₂) thin film was fabricated using titanium isopropoxide as a precursor through an atmospheric low-temperature roll-to-roll chemical vapor deposition method. TiO₂ was deposited on the PET substrate in the temperature range of room temperature to 100°C, and the working pressure was 740 Torr. The surface morphology of TiO₂ thin film was analyzed by field emission scanning electron microscopy and a 2D surface profiler. The results revealed that the growth rate of TiO₂ film was 31 nm/min at 100°C, and it also showed that the surface is uniform and smooth. Moreover, the lowest root mean square roughness (R _q) value of 1.87 nm was obtained for TiO₂ film prepared at 100°C. The composition of TiO₂ film was confirmed by X-ray photoelectron spectroscopy (XPS) analysis. The film showed very good chemical and optical properties while increasing the substrate deposition temperature. The UV–Vis spectroscopy analysis revealed that TiO₂ films exhibited excellent optical transmittance, more than 91% observed in the visible region.     

Processing of alumina‐coated glass‐bonded silicon carbide membranes for oily wastewater treatment

Crack‐free γ‐Al₂O₃‐coated glass‐bonded SiC membranes were successfully prepared using a simple heat‐treatment and dip‐coating process at a temperature as low as 850°C in air. The changes in the porosity, flexural strength, flux, and oil rejection rate of the membranes were investigated while changing the initial SiC particle size. Larger SiC particles led to bigger pores, resulting in higher flux in the oily water and a lower oil rejection rate. The SiC membranes with a support prepared from 10 μm SiC powder showed an exceptionally high oil rejection rate (99.9%) with a feed oil concentration of 600 mg/L at an applied pressure of 101 kPa. The typical porosity, flexural strength, steady state flux, and oil rejection rate of the alumina‐coated SiC membrane were ~45%, ~81 MPa, 1.78×10^?5 m³ m^?2s^?1, and 99.9%, respectively.     

High thermal conductivity of spark plasma sintered silicon carbide ceramics with yttria and scandia

A fully dense SiC ceramic with a room‐temperature thermal conductivity of 262 W·(m·K)^?1 was obtained via spark plasma sintering β‐SiC powder containing 0.79 vol% Y₂O₃‐Sc₂O₃. High‐resolution transmission electron microscopy revealed two different SiC‐SiC boundaries, that is, amorphous and clean boundaries, in addition to a fully crystallized junction phase. A high thermal conductivity was attributed to a low lattice oxygen content and the presence of clean SiC‐SiC boundaries.     

Comparative study of Al2O3, HfO2, and HfAlOx for improved self‐compliance bipolar resistive switching

The comparison of resistive switching (RS) storage in the same device architecture is explored for atomic layer deposition (ALD) Al₂O₃, HfO₂ and HfAlO_x‐based resistive random access memory (ReRAM) devices. Among them, the deeper high‐ and low‐ resistance states, more uniform V_SET‐V_RES, persistent R_OFF/R_ON (>10²) ratio and endurance up to 10⁵ cycles during both DC and AC measurements were observed for HfAlO_x‐based device. This improved behavior is attributed to the intermixing of amorphous Al₂O₃/HfO₂ oxide layers to form amorphous thermally stable HfAlO_x thin films by consecutive‐cycled ALD. In addition, the higher oxygen content at Ti/HfAlO_x thin films interface was found within the energy dispersive spectroscopy analysis (EDS). We believe this higher oxygen content at the interface could lead to its sufficient storage and supply, leading to the stable filament reduction‐oxidation operation. Further given insight to the RS mechanism, SET/RESET power necessities and scavenging effect shed a light to the enhancement of HfAlO_x‐based ReRAM device as well.     

Effect of Cryoprotectant and Freeze-Drying Process on the Stability of W/O/W Emulsions

In order to protect a hydrophilic drug and to prolong its further delivery, the formulation of multiple emulsions could be worthy. However, the double emulsions are not stable, their structure can change, leading to the formation of a single emulsion as the destruction of the system, and the drug can release easily from the globules in liquid state. The freeze-drying technology could be used to produce dry emulsion, the powder form being much more stable. The aim of this work was to study the influence of a cryoprotectant and a freeze-drying process on the stability of W/O/W emulsions. Samples were frozen at two different freezing rate (ν _f  = 0.55°C/min and 1.25°C/min) and successively dried at two different sublimation temperature (T _s  = ? 10°C and ? 20°C). The particle size distributions were measured by granulometer and UV spectrophotometer was performed to investigate the leakage of internal constituent. The glass transition temperature (T _g ) of the double emulsions was analyzed by DSC. The particle sizes became even smaller after freeze drying, except when κ-carrageenan is used as a cryoprotectant. In that case, the particles became aggregated after freeze drying, whatever the process conditions. The mean size is considerably reduced when the globules are diluted at low concentration in glucose and trehalose solution. When the concentration is increased, the size distribution is not significantly affected. The leakage of the internal aqueous phase to the external one during freeze drying was measured as an indicator of the structure stability. It is affected by the nature of the cryoprotectant and the conditions of the freeze-drying process. The leakage of the internal phase was smaller when cycle III (ν _f  = 1.25°C/min, T _s  = ? 10°C) was processed. From our experiments, we suppose that the water transfer from the inner phase to the outer aqueous phase results in the diminution of the globules size in double emulsion. The T _g of the double emulsions diluted with trehalose and glucose were determined at ? 33.8°C and ? 47.1°C. In contrast, the T _g of double emulsion with κ-carrageenan and HES did not appear.     

Preparation and Dissolution Profiles of the Amorphous,Dihydrated Crystalline,and Anhydrous Crystalline Forms of Paclitaxel

The selection of pharmaceutical polymorphisms in the final production step is very important in terms of product recovery, properties, and storage. The amorphous, dihydrated crystalline, and anhydrous crystalline forms of paclitaxel were prepared using precipitation, spray drying, and colloid formation methods. These methods were found to be highly efficient and convenient, giving high recovery, short processing time, and good stability, as compared with conventional methods such as freeze drying, evaporation, recrystallization, and melting. The polymorphic natures of the resulting paclitaxel samples were confirmed by XRPD, IR, TGA, DSC, and SEM. The dissolution rates of the paclitaxel samples were studied in pharmaceutical solvents, which included cotton seed oil, corn oil, tricaprylin, and tributyrin. For each solvent, all of the amorphous paclitaxel samples showed much higher dissolution rates than the dihydrated crystalline, anhydrous crystalline, and commercial forms, and can be used for clinical applications that demand improvements in drug delivery.     

Stabilization of Microcapsules Using a Freeze-Dried Gelatin Matrix: Aqueous Redispersibility and the Ingredient Activity

Microcapsules are of great interest to the food and pharmaceutical industries as vehicles to deliver active ingredients to the gastrointestinal tract. Drying plays an important role in stabilizing microcapsules to prolong their lifetime; however, drying often produces undesirable changes in the microcapsules, such as irreversible aggregation of the microcapsules and activity loss of the encapsulated ingredient. In this work, poly(epsilon-caprolactone) microcapsules containing a model bioactive compound (tocopherol) were prepared and stabilized in a freeze-dried gelatin matrix. This dried product was rehydrated and the aqueous redispersibility of the microcapsules and the tocopherol activity were investigated. The experimental results suggested that a kinetic balance between dehydration (caused by freezing) and gel network formation is a critical factor that affects the redispersibility and ingredient activity of the products. It was further suggested that a hydrogel-based product could be strategically freeze dried to maximize product quality by tuning its freezing process; that is, by employing a controllable dehydration process.     

Solvent screening for non‐aqueous extraction of Alberta oil sands

Non‐aqueous extraction of bitumen from oil sands has the potential to reduce fresh water demand of the extraction process and eliminate tailings ponds. In this study, different light hydrocarbon solvents, including aromatics, cycloalkanes, biologically derived solvents and mixtures of solvents were compared for extraction of bitumen from Alberta oil sands at room temperature and ambient pressure. The solvents are compared based on bitumen recovery, the amount of residual solvent in the extracted oil sands tailings and the content of fine solids in the extracted bitumen. The extraction experiments were carried out in a multistage process with agitation in rotary mixers and vibration sieving. The oil sands tailings were dried under ambient conditions, and their residual solvent contents were measured by a purge and trap system followed by gas chromatography. The elemental compositions of the extraction tailings were measured to calculate bitumen recovery. Supernatants from the extraction tests were centrifuged to separate and measure the contents of fine solid particles. Except for limonene and isoprene, the tested solvents showed good bitumen recoveries of around 95%. The solvent drying rates and residual solvent contents in the extracted oil sands tailings correlated to solvent vapour pressure. The contents of fine solids in the extracted bitumen (supernatant) were below 2.9% for all solvents except n‐heptane‐rich ones. Based on these findings, cyclohexane is the best candidate solvent for bitumen extraction, with 94.4% bitumen recovery, 5 mg of residual solvent per kilogram of extraction tailings and 1.4 wt% fine solids in the recovered bitumen. © 2012 Canadian Society for Chemical Engineering     

Effect of structural change of pitch on the thermal conductivity of epoxy‐based composites filled with heat‐treated pitch

Petroleum‐based pitches were used as filler materials to study the effects of heat‐treatment‐induced changes in pitch structure on the thermal conductivity of epoxy‐based composites. The heat treatment was performed in two steps: the first involved heating the pitch to 250 °C in order to remove the low‐molecular‐weight compounds from the pitch, and the second involved heating the pitch to either 430 or 450 °C. There was no significant difference in the curing behavior of the diglycidyl ether of bisphenol A (DGEBA)/pitch composites, regardless of the heat‐treatment temperature. However, the thermal conductivity of the DGEBA/pitch composites improved with increasing heat‐treatment temperature, and the epoxy composite prepared with pitch heat‐treated at 430 °C exhibited the maximum thermal conductivity. This can be attributed to structural changes in the pitch, such as the distance between adjacent planes (d‐spacing), crystallite height (L_c) and crystallite width (L_a). Although L_c of the pitch increased with increasing heat‐treatment temperature, the d‐spacings and L_a decreased. These results suggest that the heat treatment of the pitch led to a well‐stacked crystalline structure. However, compared with the pitch heat‐treated at 430 °C, that heat‐treated at 450 °C exhibited lower thermal conductivity in the DGEBA/pitch composite because of the low L_a, resulting in the loss of basal carbon as a consequence of in situ gasification, and pyrolysis of the low‐molecular‐weight compounds in the pitch. © 2013 Society of Chemical Industry