Preparation of Monodisperse ZrO2 by the Microwave Heating of Zirconyl Chloride Solutions

Based on the principle that the solubility of a salt decreases as the dielectric constant of the solvent decreases, zirconia powders were prepared by heating a zirconyl chloride solution with a 2-PrOH-water mixture as the solvent. The morphology, size, and size distribution of the resulting particles were highly sensitive to the heating method used on the starting solution. Particles formed under conventional heating methods were polydisperse, agglomerated spherical, or irregularly shaped because of inhomogeneous precipitation through the temperature gradient, the shear force induced by stirring, compositional nonuniformity, and the low heating rate. The present study demonstrated that microwaves provide an excellent means of heating uniformly and rapidly without stirring. The particles resulting from microwave treatment were monodisperse and spherical, with a mean diameter of 0.28 μm.     

Solid extraction of caffeine and theophylline from green tea by molecular imprinted polymers

This paper involves a feasibility study on using molecular imprinted polymers as the sorbent materials in solid phase extraction for caffeine and theophylline from green tea. Two kinds of MIPs, with caffeine-theophylline mixture and pentoxifylline-theophylline mixture as the templates respectively, MAA as the monomer, EDMA as the crosslinker and ATBN as the initiator, were applied to this purpose. Mixture solution of caffeine and theophylline (1 Μg/ ml in acetonitrile) was applied to the solid extraction cartridges following a load, wash and elute procedure with acetonitrile, methanol, methanol-acetic acid (90/10, v/v) as the solvents, respectively. This solid phase extraction protocol was applied for extraction of caffeine and theophylline from green tea. Comparison between the results obtained with the MIPs cartridges and a traditional C₁₈ reversed-phase cartridge was made. It showed that the MIP-based sorbent on the solid phase extraction was comparable with that of C₁₈ material. HPLC analysis using a C₁₈ column (5 Μm, 250× 4.6 mm from Rstech corporation), methanol: water (60 :40, v/v) as the mobile phase at a flow rate of 0.6 ml/min was applied for the quantitative determination.     

Mobile phase composition for resolving whey proteins in reversed-phase high performance liquid chromatography

Reversed-phase high-performance liquid chromatography was successfully developed for the simultaneous and rapid separation for the main whey proteins, α-Lactalbumin and β-Lactoglobulin. This method consisted of a linear gradient of the two mobile phases of 0.1% trifluoroacetic acid in water and 0.1% trifluoroacetic acid in acetonitrile. The total run time for this separation was approximately 30 min, and α-Lactalbumin was eluted followed byβ- Lactoglobulin. The injection volume was fixed at 20 μl and the flow rate was 1 ml 1/min. The optimum mobile phase composition and gradient conditions to separate α-Lactalbumin and β-Lactoglobulin (A+B) were experimentally obtained at the 15 μm particle with a pore size of 300 Å on the linear-gradient mode.     

Effect of reactive diluents on properties of unsaturated polyester/montmorillonite nanocomposites

Unsaturated polyester (UP)/montmorillonite (MMT) nanocomposite was prepared by using hydroxypropylacrylate (HPA) as a reactive diluent instead of conventional styrene monomer and the effect of polarity of reactive diluent on properties of nanocomposite was investigated. X‐ray and mechanical test data indicated that mixing for an extended period of time is essential to enhance the physical properties of nanocomposites in the UP/Cloisite 6A system. This was attributed to the high polarity of HPA that may disturb the preintercalation of UP resin into the galleries of MMT. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 238–242, 2004     

Monodisperse polymer/metal composite particles by electroless chemical deposition: Effect of surface functionality of polymer particles

Micron‐sized polymer particles were coated with layers of nickel compounds by plating electrolessly in the presence of aqueous solutions of nickel chloride, sodium hypophosphite, sodium citrate, and ammonium chloride at elevated temperature. The uniform functional polymer particle could be obtained by seeded polymerization. To investigate the effect of surface functionality on the conditions for nickel deposition, the polymer particle was functionalized with the thiol group. From morphological observation, it was found that the mode of nickel deposition was greatly dependent on the surface functionality of the polymer particle. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 420–424, 2003     

Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Molecular simulation of hydrogen adsorption in organic zeolite

The adsorption of molecular hydrogen on model zeolites has been simulated employing Grand Canonical Monte Carlo (GCMC) procedure. The effects of cation type, available volume, surface area, temperature, pressure and pre-adsorbed organics such as benzene on the hydrogen uptake are analyzed. The hydrogen adsorption can be affected mainly by the available volume and surface area per g-zeolite at the same temperature and pressure. Increase of temperature results in the decrease of sorption intensity and capacity. The adsorption capacity correlates well with the pressure with high linearity at room temperature. Adsorption is lowered by the pre-adsorbed benzene molecule. The orientation and the number of benzene molecule in zeolite affect the adsorption capacity. The organic zeolite with larger available volume shows larger adsorption capacity.     

Mechanical properties and structures of dicyanate–clay nanocomposites

Dicyanate–clay nanocomposites comprising a dicyanate resin and a type of organically modified clay were prepared and characterized, and their thermomechanical properties were investigated. The organically modified clay had silicate layers of nanometer size intercalated with an organic modifier, which improved the compatibility between the clay and organic materials, such as dicyanate resins. Dynamic mechanical analysis was performed to investigate the thermomechanical properties of the dicyanate–clay nanocomposites containing various amounts of the clay. The storage modulus of the nanocomposites below their glass‐transition temperatures slightly increased with increasing clay content. The glass‐transition temperature of the dicyanate–clay nanocomposites increased with increasing clay content. The nanostructures of the dicyanate–clay nanocomposites were characterized by transmission electron microscopy and X‐ray diffraction analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2629–2633, 2003     

Preparation and properties of electrospun poly(vinyl alcohol)/silver fiber web as wound dressings

A novel wound dressing material was prepared by electrospinning poly(vinyl alcohol) (PVA)/AgNO₃ aqueous solution into nonwoven webs and then treating the webs by heat or UV radiation. Through SEM, TEM, and XPS analyses, it was observed that the silver (Ag) nanoparticles were generated and existed in the near surface of the electrospun nanofibers. It was found that heat treatment as well as UV radiation reduced the Ag⁺⁺⁺ ions in the electrospun PVA/AgNO₃ fiber web into the Ag nanoparticles. Also the heat treatment improved the crystallinity of the electrospun PVA fiber web and so it made the web unsolved in moisture environment. Therefore, it was concluded that the only heat treated electrospun PVA/AgNO₃ fiber web was a good material as wound dressings because it had structural stability in moisture environment as well as excellent antimicrobial ability and, quick and continuous release of the effectiveness. POLYM. ENG. SCI., 47:43–49, 2007. © 2006 Society of Plastics Engineers     

Biodegradability of cellulose fabrics

Biodegradability of cellulose fabrics was evaluated by use of a soil burial test, an activated sewage sludge test, and an enzyme hydrolysis. Surface changes after biodegradation were observed by optical microscopy. From X‐ray diffraction analysis (XRD), changes in the crystallinities and the internal structures as a result of degradation were also investigated. It was shown that biodegradability decreased in the following order: rayon > cotton ? acetate. Rayon fibers, which have a low crystallinity and a low degree of orientation, showed the highest biodegradability in most cases. However, in spite of its low crystallinity, acetate fibers exhibited very low biodegradability, probably because of the presence of hydrophobic groups in its structure. On the other hand, linen showed an inconsistent behavior in that it had the highest biodegradability in the soil burial test, but a lower biodegradability than that of cotton in the activated sewage sludge test. XRD analysis revealed that there was a slight increase in the crystallinity of linen, cotton, and rayon fabrics at the initial stage, but a continuous decrease thereafter. From the correlation analysis, it was revealed that the biodegradability of cellulose fabrics was closely related to the moisture regain of the fibers, which reflects the hydrophilicity and internal structure of the fibers at the same time. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 248–253, 2004