Sieving of aerosol particles with metal screens

Metal screens with uniform micrometer-sized opening were employed to sieve aerosol particles by suppressing the adhesion of particles smaller than the openings. The collection efficiencies of monodispersed polystyrene latex (PSL) particles were experimentally determined using the metal screens with 1.2, 1.8, 2.5, and 4.2 μm openings at various filtration velocities. The particles smaller than the mesh opening adhered on the metal screen at a low filtration velocity, but the bounce-off of particles on the mesh surface suppressed the adhesion at a high velocity. As a result, we found that the adhesion of PSL particles larger than 0.3 μm mostly suppressed at a filtration velocity higher than 10 m s^?1 and therefore we can sieve aerosol particles according to the opening size of metal screens. We also found that the particle number concentration could be determined by measuring the increase in pressure drop since the clogging of metal screen openings takes place by the individual particles.

© 2016 American Association for Aerosol Research     

Fabrication of 80 mm diameter-sized solid oxide fuel cells using a water-based NiO–YSZ slurry

Solid oxide fuel cells (SOFCs) are very attractive for their high energy conversion efficiency and low emissions. Generally, a supported layer of SOFCs is fabricated by tape casting, using an organic solvent. Recently, a slurry based on water instead of an organic solvent has been sought in order to avoid environmental pollution. In this study, the anode of SOFCs was fabricated by aqueous tape casting, and the electrolyte and the cathode were deposited by screen printing. The I–V characteristics of the cell thus obtained were evaluated. As a result, an 80 mm diameter-sized cell with a power density of 0.33 W/cm² at 800 °C was successfully fabricated by controlling sintering conditions.     

On-off switching properties of one-dimensional photonic crystals consisting of azo-functionalized polymer liquid crystals having different methylene spacers and polyvinyl alcohol

In this paper, photoresponsive behavior of multi-bilayered films having precisely controlled layer thickness prepared by stacking an azo-functionalized polymer liquid crystal, PMAzXAc, and polyvinyl alcohol alternatively, PVA, is described. The multi-bilayered films were found to reflect a light of specific wavelength depending on the layer thickness and refractive index, and showed the reversible change in the reflection intensity by irradiation with visible and UV lights. The change in the reflection intensity was brought about by change in the molecular orientation of PMAzXAc between an out-of-plane orientation and a photo-induced isotropic state, and was strongly dependent on the number of methylene spacer of PMAzXAc linking the azobenzene side group with the acrylate polymer main chain. PMAz6Ac with hexa-methylene spacer showed the largest change in the reflection intensity, while smaller change in the reflection intensity was observed for PMAzXAc having shorter or longer methylene spacer than 6. The effect of the methylene spacers on the photochemical change in the molecular orientation of azobenzene chromophores in the multi-bilayered films will be discussed.     

Numerical simulation of tip leakage vortex effect on hydrogen-combustion flow around 3D turbine blade

In these years, a lot of environmental problems such as air pollution and exhaustion of fossil fuels have been discussed intensively. In our laboratory, a hydrogen-fueled propulsion system has been researched as an alternative to conventional systems. A hydrogen-fueled propulsion system is expected to have higher power, lighter weight and lower emissions. However, for the practical use, there exist many problems that must be overcome. Considering these backgrounds, jet engines with hydrogen-fueled combustion within a turbine blade passage have been studied. Although some studies have been made on injecting and burning hydrogen fuel from a stator surface, little is known about the interaction between a tip leakage vortex near the suction side of a rotor tip and hydrogen-fueled combustion. The purpose of this study is to clarify the influence of the tip leakage vortex on the characteristics of the 3-dimensional flow field with hydrogen-fueled combustion within a turbine blade passage. Reynolds-averaged compressible Navier-Stokes equations are solved with incorporating a k-ε turbulence and a reduced chemical mechanism models. Using the computational results, the 3-dimensional turbulent flow field with chemical reactions is numerically visualized, and the three-dimensional turbulent flow fields with hydrogen combustion and the structure of the tip leakage vortex are investigated.     

Substituent effects on thermal and photo‐alignment behavior of poly(ethylene imine)s carrying azobenzene side groups

A new class of liquid‐crystalline poly(ethylene imine)s (PEIs) having four differently substituted (? CN,? C₄H₉,? OCH₃ and? NO₂) azobenzene side‐chain groups attached through alkyl spacer groups were successfully synthesized using a solution polycondensation reaction. The synthesized polymers were characterized using differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. The photochemical, thermo‐optical and photo‐orientational behavior of the polymers were investigated in detail. Spin‐coated films of PEIs with azobenzene groups having? C₄H₉,? OCH₃ and? NO₂ substituents showed out‐of‐plane molecular orientation on annealing. Except for the PEI with an azobenzene group having ? NO₂ substituent, all polymers exhibited good photoresponsive properties upon irradiation with UV and visible light. Films of PEIs with azobenzene side groups having? CN,? C₄H₉ and? OCH₃ substituents showed reversible alignment behavior from random state to out‐of‐plane and from out‐of‐plane to random state on annealing and on irradiation with UV and non‐polarized visible light. The reversibility of the molecular orientation of PEIs from random state to out‐of‐plane and from out‐of‐plane to random state greatly depended on the substituent attached to the azobenzene side‐chain group. Copyright © 2010 Society of Chemical Industry     

Synthesis and optical properties of azobenzene side chain polymers derived from the bifunctional fumaric acid and itaconic acid

Three type polymers containing the same azobenzene side chain group with different backbone structures, poly(DMAz6Fm), poly(DMAz6It) and poly(MAz6Ac) derived respectively from fumaric acid, itaconic acid and acrylic acid, were synthesized. The dependence of photo-response properties on the polymeric architecture was investigated for the solutions and films. By irradiation of the linearly polarized light (436 nm), uniaxial orientations of the thin films were induced and anisotropic properties were investigated by measurements of the order parameters and birefringence values.     

HR-TEM observation of laser pressure weld of galvannealed steel and pure aluminium

Laser pressure welding was conducted by changing the laser power and the roller pressure in the previous experiment. It was revealed that dissimilar metal welding of galvannealed steel and pure aluminium was feasible in a wide range of welding conditions. When the roller pressure was more than 1.96 kN at the laser powers equal to or less than 1400 W, the joint strengths were so high that the specimens in the tensile shear and the peel tests fractured in the A1050 parent metal.

In order to know the reason for such high strengths of joints with thick compound layers and the joining mechanism, the compound layer was observed by HR-transmission electron microscopy (TEM). The TEM observation results revealed that the main phase in the compound layer was the solid solution of Al + Zn. Moreover, the intermetallic compound was identified as FeAl, Fe₂Al₅, Fe₄Al₁₃ and Fe₂Al₅Zn_0.4 phase by electron diffraction. The Fe₃Zn₁₀ (Γ phase) of Fe–Zn intermetallic compound was confirmed on a Fe base material. It is guessed that the joining areas were heated at a range of 782°C more than 665°C, a melting point of Al, by laser irradiation because the δ_lk phase aspect was not confirmed. Because the surfaces of A1050 and Zn plated layer were melted thinly, the layer was over 10 μm thicker. The reason for the production of high-strength joints with a relatively thick intermetallic compound layer was attributed to the formation of (Al + Zn) phase with finely dispersed intermetallic compounds.     

Investigation for Necessity of Dispersivity and Tortuosity in the Dusty Gas Model for a Binary Gas System in Soil

Diffusion, dispersion, and advection are important processes in multi-gas systems in soils. To date, both Fick's model and the Dusty Gas (DG) model have been used to model the movement of gases in these systems. Dispersion is included in the dispersion-advection equation with Fick's Model for the movement of gases in gas-phase of soil, yet the movement of gases in multi-component gas-soil systems is considered to be expressed more accurately by the DG model than by Fick's model. However to date, no study has investigated the necessity of considering dispersion in the Dusty Gas (DG) model. We carried out column experiments for nitrogen-methane, nitrogen-carbon dioxide, and carbon dioxide-methane binary gas systems in sandy soil, and also did simulations on the same systems using both Fick's model and the DG model. A comparison of the results of the column experiments with our simulations confirmed that there was no need to consider the dispersion in the advection-diffusion equations with the DG model when the velocity of gas was 0.05-0.4 cm/s in Toyoura sand. Furthermore, our experiments and simulations with the DG model showed that, rather than dispersion, tortuosity should be taken into account in application of the DG model to the above condition.     

In-vivo human brain molecular imaging with a brain-dedicated PET/MRI system

Advances in the new-generation of ultra-high-resolution, brain-dedicated positron emission tomography-magnetic resonance imaging (PET/MRI) systems have begun to provide many interesting insights into the molecular dynamics of the brain. First, the finely delineated structural information from ultra-high-field MRI can help us to identify accurate landmark structures, thereby making it easier to locate PET activation sites that are anatomically well-correlated with metabolic or ligand-specific organs in the neural structures in the brain. This synergistic potential of PET/MRI imaging is discussed in terms of neuroscience and neurological research from both translational and basic research perspectives. Experimental results from the hippocampus, thalamus, and brainstem obtained with ¹⁸F-fluorodeoxyglucose and ¹¹C-3-amino-4-(2-dimethylaminomethylphenylsulfanyl)benzonitrile are used to demonstrate the potential of this new brain PET/MRI system.