Synthesis and characterization of phosphonate and aromatic-based polynorbornene polymers derived from the ring opening metathesis polymerization method and investigation of their thermal properties

In the present study, phosphonate ester, phosphonic acid, and aromatic (phenyl, naphthalene, anthracene) groups containing polymers were synthesized by the ROMP method to analyze thermal properties of these polymers. Thermal stability of the synthesized polymers is tested by thermal gravimetric analysis under nitrogen, air, and microscale combustion calorimetry analysis. Analysis shows that thermal behavior is directly related to the phosphorus level in the copolymer series. All the polymers are thermally stable under nitrogen and air up to 900 °C. Synergistic charring effect under air was observed between aromatic groups and phosphonic acid functionality in the copolymer series. Anthracene units have a greater potential to form carbonaceous char than the naphthalene and phenyl units. Phosphonate ester and naphthalene units bearing copolymers (P3A) gave 8.13% char yield at 900 °C under air. Phosphonic acid derivatives of this polymer, P3D, gave a highest char residue of 17.15% under the same condition. The introduction of phosphonate and phosphonic acid in each copolymer series is also beneficial in reducing the peak heat release rate (PHRR). Cleavage of the phosphonate ester bearing homopolymer (P4) to phosphonic acid (P4A) causes a sharp decrease in the PHRR ratio from 274 to 28.2 W/g. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47085.     

Comparison of different ultrasound support methods during colour and chemical oxygen demand removal of disperse and reactive dyebath solutions by ozonation

In this study, the effects of ozonation, ozonation with ultrasonic bath and ozonation with ultrasonic homogeniser processes on colour and chemical oxygen demand removal properties of disperse (CI Disperse Red 60, CI Disperse Blue 337) and reactive (CI Reactive Blue 171 and CI Reactive Blue 19) dyebath solutions with and without dyeing auxiliaries were investigated. Chemical oxygen demand (in mg/l) and colour (in Hazen) measurements of the studied dyebath solutions were determined. The ozonation process caused simultaneous chemical oxygen demand removal during decolorisation. However, the improvement in chemical oxygen demand reduction was less than of that on decolorisation. The application of the combination of ozonation with ultrasonic homogeniser is the most efficient process and creates a great time advantage over the other process types studied (ozonation alone and ozonation with ultrasonic bath) to reach the same colour and levels of chemical oxygen demand removal.     

The Effects of Ozone Treatment on Soybean Fibers

A set of knitted fabrics comprising soybean fibers was ozonated at room temperature for periods ranging from 2.5 to 300 minutes to identify any accompanying effects on either physical properties (specifically whiteness and burst-strength), fiber surface integrity or microstructure. A hydrogen peroxide treatment was applied to some of the fabric in order to provide a comparison. Ozonation was found to produce a promising increase in whiteness which, after the maximum exposure time, was significantly higher than was achieved using hydrogen peroxide.     

Synthesis of phosphorus‐ and phenyl‐based ROMP polymers and investigation of their effects on the thermomechanical and flammability properties of a polypropylene–IFR system

In this study, we present an approach for the synthesis of novel phosphorous‐ or phenyl‐ containing polymers, 2_phenyl, 3_phospho, and 2_phenyl‐co‐3_phospho, derived from ring‐opening metathesis polymerization (ROMP), to reduce the flammability of polypropylene (PP). The composites were processed by melt‐blending ROMP polymers and octaphenyl–polyhedral oligomeric silsesquioxane with PP/intumescent flame retardant (IFR) compounds at different compositions. The composites were characterized by limiting oxygen index (LOI), UL‐94, and mechanical tests as well as thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The molecular structures of phosphorous‐ and phenyl‐containing polymers were proved by ¹H‐NMR, ¹³C‐NMR, and Fourier transform infrared spectroscopy. The online rheological measurements indicated that the addition of additives to the PP/IFR system increased the melt viscosity of the compounds regardless of the type. The DSC analysis showed that the addition of ROMP polymers to the PP/IFR system influenced the crystal perfection and degree of crystallization. TGA analysis of the composites revealed that the addition of ROMP polymers to PP/IFR compounds deteriorated the thermal stability as the amount of phosphorus increased in the matrix. Dynamic mechanical properties such as storage modulus (E′) and loss modulus (E″) of the composites were lowered by the addition of ROMP polymers. The LOI and UL‐94 rating of PP/IFR were enhanced by the addition of ROMP polymers. It was successfully demonstrated that the novel phosphorous‐ or phenyl‐containing polymers were highly potent additives in optimizing the flammability of PP composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45998.     

Effect of nano-silica on the chemical durability and mechanical performance of fly ash based geopolymer concrete

In this study, the effect of nano silica on the short term severe durability performance of fly ash based geopolymer concrete (GPC) specimens was investigated. Four types of GPC were produced with two types of low calcium fly ashes (FAI and FAII) with and without nano silica, and ordinary Portland cement concrete (OPC) concrete was also cast for reference. For the geopolymerization process, the alkaline activator has selected a mixture of sodium silicate solution (Na₂SiO₃) and sodium hydroxide solution (NaOH) with a ratio (Na₂SiO₃/ NaOH) of 2.5. Main objectives of the study were to investigate the effect of usability or replaceability of nano silica-based low calcium fly ash based geopolymer concretes instead of OPC concrete in structural applications and make a contribution to standardization process of the fly ash based geopolymer concrete. To achieve the goals, four types of geopolymer and OPC concretes were subjected to sulfuric acid (H₂SO₄), magnesium sulfate (MgSO₄) and seawater (NaCl) solutions with concentrations of 5%, 5%, and 3.5%, respectively. Visual appearances and weight changes of the concretes under chemical environments were utilized for durability aspects. Compressive, splitting tensile and flexural strength tests were also performed on specimens to evaluate the mechanical performance under chemical environments. Results indicated that FAGPC concretes showed superior performance than OPC concrete under chemical attacks due to low calcium content. Amongst the chemical environments, sulfuric acid (H₂SO₄) was found to be the most dangerous environment for all concrete types. In addition, nano silica (NS) addition to FAGPC specimens improved both durability and residual mechanical strength due to the lower porosity and more dense structure. The FAIIGPC specimens including nano silica showed the superior mechanical performance under chemical environment.     

A novel polymer critical re-melting treatment for improving corrosion resistance of magnesium alloy stent

Polymer coating was widely used as a protective coating on Mg alloy stent due to its excellent deformability. However, the polymer coating with lots of macro- and micro-holes after solvent evaporation during forming process would make corrosion medium permeate easier and decrease the corrosion resistance of Mg alloy stent. In this study, a novel critical re-melting method was adopted to improve the polymer coating densification, which was evaluated by the surface morphology of coating. The corrosion resistance of Mg alloy stent after critical re-melting treatment was examined by the electrochemical and immersion tests. The results indicated that the corrosion resistance of Mg alloy stent with polymer coating was improved significantly by polymer critical re-melting treatment.     

A comparison of different activated carbon performances on catalytic ozonation of a model azo reactive dye

The objective of this study is to compare the performances of catalytic ozonation processes of two activated carbons prepared from olive stone (ACOS) and apricot stone (ACAS) with commercial ones (granular activated carbon-GAC and powder activated carbon-PAC) in degradation of reactive azo dye (Reactive Red 195). The optimum conditions (solution pH and amount of catalyst) were investigated by using absorbencies at 532, 220 and 280 nm wavelengths. Pore properties of the activated carbon (AC) such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by N(2) adsorption. The highest BET surface area carbon (1,275 m(2)/g) was obtained from ACOS with a particle size of 2.29 nm. After 2 min of catalytic ozonation, decolorization performances of ACOS and ACAS (90.4 and 91.3%, respectively) were better than that of GAC and PAC (84.6 and 81.2%, respectively). Experimental results showed that production of porous ACs with high surface area from olive and apricot stones is feasible in Turkey.     

Analyzing the solutions of DEA through information visualization and data mining techniques: SmartDEA framework

Data envelopment analysis (DEA) has proven to be a useful tool for assessing efficiency or productivity of organizations, which is of vital practical importance in managerial decision making. DEA provides a significant amount of information from which analysts and managers derive insights and guidelines to promote their existing performances. Regarding to this fact, effective and methodologic analysis and interpretation of DEA results are very critical. The main objective of this study is then to develop a general decision support system (DSS) framework to analyze the results of basic DEA models. The paper formally shows how the results of DEA models should be structured so that these solutions can be examined and interpreted by analysts through information visualization and data mining techniques effectively. An innovative and convenient DEA solver, SmartDEA, is designed and developed in accordance with the proposed analysis framework. The developed software provides DEA results which are consistent with the framework and are ready-to-analyze with data mining tools, thanks to their specially designed table-based structures. The developed framework is tested and applied in a real world project for benchmarking the vendors of a leading Turkish automotive company. The results show the effectiveness and the efficacy of the proposed framework.     

CdO/Cu2O solar cells by chemical deposition

CdO and Cu₂O thin films have been grown on glass substrates by chemical deposition method. Optical transmittances of the CdO and Cu₂O thin films have been measured as 60–70% and 3–8%, respectively in 400–900 nm range at room temperature. Bandgaps of the CdO and Cu₂O thin films were calculated as 2.3 and 2.1 eV respectively from the optical transmission curves. The X-ray diffraction spectra showed that films are polycrystalline. Their resistivity, as measured by Van der Pauw method yielded 10⁻²–10⁻³ Ω cm for CdO and approximately 10³ Ω cm for Cu₂O. CdO/Cu₂O solar cells were made by using CdO and Cu₂O thin films. Open circuit voltages and short circuit currents of these solar cells were measured by silver paste contacts and were found to be between 1–8 mV and 1–4 μA.     

有故事的空间 比利时布鲁塞尔某酒吧

当业主Francesco Ravo遇到一个千载难逢的机会买下这所位于比利时布鲁塞尔美丽的圣公会大教堂的时候,他便毫不犹豫的在心中设计了对大教堂空间的改造计划。他认为人的一生中没有多少机会能