新型高耐蚀车辆保护蜡的研究

研制了一种耐蚀性能要求较高环境下使用的车辆保护蜡，采用高分子树脂，防锈添加剂与蜡膜相结合的方法，大幅提高了耐蚀性等质量性能，满足了厂家和用户的要求，成功应用于车辆的涂装。     

那曲典型草地植被光谱特征分析

遥感是大尺度生态研究的重要工具之一,而地面植物群落特征与其光谱特征之间的关系是解译遥感影像的关键。地面实测数据由于其高空间分辨率和高光谱分辨率,能够准确反映地物光谱信息,可以用来指导卫星遥感解译工作,同时为遥感监测草地退化、草地模型建立等提供数据支持。选取西藏那曲地区的优势植被类型作为研究对象,利用ASD FieldSpec 3便携式光谱仪测定优势种的冠层光谱并进行比较,并取其中一种优势种测量其在不同覆盖度和不同生长期的光谱反射特点。研究结果表明:①不同植被群落冠层光谱具有特殊的光谱曲线,可见光波段光谱反射率依次是紫花针茅、小嵩草和藏北嵩草,近红外波段光谱反射率则依次是小嵩草、藏北嵩草和紫花针茅;红边位置可以识别藏北嵩草,但是不能区分小嵩草和紫花针茅;②不同覆盖度的小嵩草红边、“绿峰”位置不随覆盖度的变化而发生变化;连续统去除后得到吸收深度随覆盖度的增加而变大,吸收峰面积随覆盖度的增加而增加;③小嵩草衰退期内,在可见光波段和红边波段,冠层光谱反射率随着叶绿素含量的减少而下降,出现“红边蓝移,绿峰下降”的现象。     

一种基于差分进化和免疫克隆选择算法的混合优化方法

为了提高免疫克隆选择算法的搜索能力,提出了一种基于差分进化和免疫克隆选择算法的混合优化方法。该方法采用差分进化提高免疫克隆选择算法的抗体亲和度,并对该算法的收敛性进行了分析。为了测试该算法的有效性,将该算法应用于函数优化问题中。仿真结果表明,该方法具有更高的收敛速度和收敛精度。     

Exothermic effect in the process of electron‐beam curing of epoxy resins

Temperature measurements have been performed in the process of electron‐beam curing of EB‐I and EB‐II epoxy resin systems. The influence of initiator content, resin type, and dose rate on the temperature of the systems was studied. Transverse and longitudinal temperatures of samples in the glass vessel were also analyzed. The nature of temperature curves varied with the different epoxy resin systems in the steel mold, but did not change with different contents of the initiator. At the same time, the heat had no effect on the gel fraction of epoxy resin systems. The temperature curve was greatly affected by the dose rate, and its peak value, peak width, and plateau value also increased with it. The transverse temperature of EB‐II glass vessel samples increased as the radiation dose increased and, in the same sample, the temperature reduced as the distance between the radiation center and the test point increased. The longitudinal temperature of EB‐I and EB‐II resin systems in a glass vessel decreased as the radiation depth increased. As the radiation dose increased, the temperature of the EB‐I resin system increased simultaneously, while that of the EB‐II resin system initially increased and then kept constant when the dose reached a certain value. The temperatures of these two resin systems decreased rapidly when the radiation process stopped. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2217–2222, 2004     

全硫化粉末丁腈橡胶改性硬质聚氯乙烯研究

研究了纳米级全硫化粉末丁腈橡胶（VP-401）对硬质聚氯乙烯（PVC-U）增韧改性材料的力学性能、流变性能及形态结构的影响。研究发现：与普通粉末橡胶P83增韧相比，采用少量的超细全硫化粉末橡胶即可在保持较高的强度和耐热温度的基础上大幅度提高硬质PVC材料的冲击韧性。     

Oxygen enrichment from air through multilayer thin low‐density polyethylene films

Several multilayer thin low‐density polyethylene (LDPE) films were fabricated by blown thin film having a thickness of 7 μm and an area of 130 cm². They were characterized for their oxygen‐enrichment performance from air by a constant pressure–variable volume method in a round permeate cell with an effective area of 73.9 cm². The relationship between oxygen‐enrichment properties, including oxygen‐enriched air (OEA) flux, oxygen concentration, permeability coefficients of OEA, oxygen, nitrogen, as well as separation factor through the multilayer LDPE films, and operating parameters, including transfilm pressure difference, retentate/permeate flux ratio, temperature, as well as layer number, are all discussed in detail. It is found that all of the preceding oxygen‐enrichment parameters increase continuously with an increase of transfilm pressure difference from 0.1 to 0.65 MPa, especially for the trilayer and tetralayer LDPE films. The oxygen concentration and separation factor appear to rapidly increase within the retentate/permeate flux ratio below 200, and then become unchangeable beyond that, whereas the OEA flux and the permeability coefficients of OEA, oxygen, and nitrogen seem to remain nearly constant within the whole retentate/permeate flux ratio investigated, especially for the monolayer and bilayer LDPE films. The selectivity becomes inferior, whereas the permeability becomes superior, as the operating temperature increases from 23 to 31°C. The highest oxygen concentration was found to be 44.8% for monolayer LDPE film in a single step with air containing oxygen of 20.9% as a feed gas and operating pressure of 0.5 MPa at a retentate/permeate flux ratio of 340 and 23°C. The results demonstrate a possibility to prepare an oxygen‐enriching membrane directly from air, based on the easily obtained thin LDPE films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3013–3021, 2002; DOI 10.1002/app.2331     

Mechanical and erosion properties of CaCO3‐EMAA thermal sprayed coatings

Polymer‐ceramic composite coatings manufactured from calcium carbonate and ethylene‐methacrylic acid copolymer (EMAA) were prepared via a thermal spray process employing different CaCO₃ filler sizes (average size of 2.8, 9 or 36 μm) and loading levels from about 2.5 to 7 wt%. The optimum filler feeding characteristics, deposition efficiency and deposition rate were obtained with a 36 μm sized CaCO₃. Tensile properties, peel strength, and the erosion resistance of a pure EMAA and CaCO₃‐EMAA composite coatings were investigated. It was found that the tensile strain at fracture of the composite coating decreased with the addition of filler to a greater degree than that observed in compression‐molded polymer composites. This is attributed to an inhomogenous distribution of the filler, with more being concentrated at the boundaries of the deposited polymer particles, thereby establishing a rigid framework within the coating. Only a small filler content is necessary to establish large changes in the mechanical properties of the coating. The peel strength of a composite coating decreases with filler content, both on a mild steel substrate and a previously sprayed polymer coating. Bonding to the latter is significantly higher and offers a possibility as a bonding layer between substrates and composite coatings. The coefficient of friction is lowered with the addition of a filler. Erosion testing has shown that the erosion resistance of PF111 is little improved overall with filler addition, although some increase is found for filler contents less than 5 vol%. Polym. Eng. Sci. 44:1448–1459, 2004. © 2004 Society of Plastics Engineers.     

十二烷基苯磺酸钠水溶液聚集性质的研究

用滴体积法测出十二烷基苯磺酸钠（ＳＤＢＳ）稀水溶液的表面张力；然后求出其临界胶束浓度（ＣＭＣ）。同时通过溶液的电导率、吸收光谱以及荧光光谱测定求出其ＣＭＣ。这样测出的ＣＭＣ值为１．２～１．６×１０－３ｍｏｌ／Ｌ，与文献值相符。也研究了部分水解的聚丙烯酰胺（ＰＨＰＡＭ）对ＳＤＢＳ聚集性质的影响；发现ＳＤＢＳ的ＣＭＣ值随ＰＨＰＡＭ的加人而减少并且ＰＨＰＡＭ水溶液的粘度随ＳＤＢＳ的存在而急剧降低（类似盐效应）。这些方法与性质对强化采油（ＥＯＲ）是重要的。     

粘度调节剂对制备环氧树脂微球的影响

研究粘度调节剂对环氧树脂/二氨基二苯基砜/聚醚酰亚胺(EP/DDS/PEI)共混物相结构及制备EP微球的影响。结果表明,共混物中加入粘度调节剂后,固化过程中共混体系的粘度明显降低,随着粘度调节剂用量的增加,EP分散相尺寸逐渐增大,制得的EP微球粒径及粒径分布指数逐渐增大。EP微球的红外光谱显示粘度调节剂对EP微球的成分和相结构没有明显影响。     

PP/POE/Nano-CaCO3复合材料的动态力学热分析

采用熔融共混工艺制备了聚丙烯(PP)／聚烯烃热塑性弹性体(POE)／纳米CaCO3复合材料。用动态力学试验方法研究了PP／Nano-CaCO3、PP／POE和PE／POE／Nano-CaCO3复合材料的动态力学特征。结果显示：PP／Nano-Ca-CO3PP／POE二元体系的低温内耗峰强度均比PP大；PP／POE／Nano-CaCO3三元复合体系的低温内耗峰强度较之二元体系明显增强，在PE／POE／Nano-CaCO3复合体系中，POE及Nano-CaCO3共同作用使体系tgδ1转变峰逐渐消失，tgδ2峰变宽、增强。利用扫描电子显微镜观察了不同体系的形态，三元复合体系由纯PP的耗能少的空洞化断裂方式逐步向耗能多的基体层屈服方式变化；质量比为100／10／10的PE／POE／Nano-CaCO3复合材料的低温内耗峰强度最大，冲击强度较纯PP提高了178％。