Experimental Verification to Estimate Ground Thermal Conductivity Using Spiral Coil Type Ground Heat Exchangers

This paper presents an experimental study on the evaluation of thermal response of a spiral coil type GHE （ground heat exchanger）. This GHE was installed on partially saturated landfill ground that was composed of silt and clay in the runway area of Incheon International airport. TRT （thermal response test） was conducted for more than 65 hours under continuous operation conditions. Ground thermal conductivity was derived based on line source theory, which has usually been found to be appropriate for line type GHEs such as U, W and 2U types. A reasonable method to derive ground thermal conductivity using the infinite line source theory for a spiral coil type GHE was introduced. Ground thermal conductivity from the TRT using spiral coil type GHE was compared with those from the analytical equivalent model of ground thermal conductivity.     

Sensitivities of input parameters for predicting stability of soil slope

Bulletin of Engineering Geology and the Environment - The infinite slope stability model is the basis for predicting the slope stability; however, the fundamental theory requires various input...     

Study on residual stress in viscoelastic thin film using curvature measurement method

Using LSM (laser scanning method), the radius of curvature due to thermal deformation in polyimide film coated on Si substrate is measured. Since the polyimide film shows viscoelastic behavior, i.e., the modulus and deformation of the film vary with time and temperature, we estimate the relaxation modulus and the residual stresses of the polyimide film by measuring the radius of curvature and subsequently by performing viscoelastic analysis. The residual stresses relax by an amount of 10% at 100°C and 20% at 150°C for two hours.     

A study on the fault diagnosis of the 3-d roll shape in cold rolling

The metal processing system usually consists of various components such as motors, work rolls, backup rolls, idle rolls, sensors, etc. Even a simple fault in a single component in the system may cause a serious damage on the final product. It is, therefore, necessary to diagnose the faults of the components to detect and prevent a system failure. Especially, the defects in a work roll are critical to the quality of strip. In this study, a new 3-D diagnosis method was developed for roll shape defects in rolling processes. The new method was induced from analyzing the rolling mechanism by using a rolling force model, a tension model, the Hitchcock’ s equation, and measurement of the strip thickness, etc. Computer simulation shows that the proposed method is very useful in the diagnosis of the 3-D roll shape.     

Removal of chlorophenols from groundwater by chitosan sorption

The equilibrium and kinetics of chlorophenol (CP) sorption by chitosan, poly D-glucosamine, were studied under simulated groundwater conditions. Lower temperature, from 25 degrees C to 15 degrees C and then 5 degrees C, markedly decreased the adsorption rates by a factor of 30-53% and 7-22%. Comparison between two types of chitosan, flakes and highly swollen beads, demonstrated that the maximum pentachlorophenol (PCP) uptake capacities in Langmuir and Freundlich models depend on the specific surface area of the particle. Low temperature (5 degrees C) significantly increased the PCP uptake capacity in comparison to higher temperatures (15 degrees C and 25 degrees C). PCP uptake capacity was halved at pH levels higher than 6.5, and NaCl concentrations greater than 1% blocked PCP sorption almost completely. Of five kinds of chlorophenols, i.e. 2,4,6-trichlorophenol (2,4,6-TCP), 3,4-dichlorophenol (3,4-DCP), 2,3-dichlorophenol (2,3-DCP), 2,6-dichlorophenol (2,6-DCP), 3-monochlorophenol (3-MCP), TCP had the maximum sorption efficiency on flake-type chitosan, followed by DCPs, and finally MCP (the three kinds of DCP, with the same elemental compositions, achieved similar sorption performances).     

Effect of various processing methods on the interfacial reactions in SiCp/2024 Al composites

SiC_p/2024 Al composites were prepared using various processing techniques, such as spray forming, powder metallurgical hot pressing, thixoforming, and compocasting. The interfacial characterizations of these composites were performed using scanning electron microscopy, Auger electron spectrometry, transmission electron microscopy, and X-ray diffraction on reaction products extracted using the electrochemical dissolution. The value of these combined techniques in elucidating the morphologies of the interfacial reaction products was also demonstrated. The influence that each fabrication process has on the extent of the interfacial reaction was studied. Adequate process parameters to fabricate SiC_p/Al alloy composites were proposed based on thermodynamic considerations.     

Precipitation behavior of Mg17Al12 in monolithic and Al2O3 short fiber reinforced Mg-Al-Zn alloys

The precipitation behavior of Mg₁₇Al₁₂ in monolithic and Al₂O₃ short fiber reinforced Mg-Al-Zn alloys was investigated by optical and transmission electron microscopies and hardness measurements. The maximum hardness was obtained when the long and short axes of the platelet type continuous Mg₁₇Al₁₂ precipitates were about 0.3 μm and 0.04 μm, respectively. The area fraction of the discontinuous Mg₁₇Al₁₂ precipitate nodule reached about 0.23. The coarsening behavior of the discontinuous Mg₁₇Al₁₂ precipitate nodule was found to obey the relationship suggested by the Johnson-Mehl-Avrami model. The slope of the Johnson-Mehl-Avrami plot for the Al₂O₃ short fiber reinforced Mg-Al-Zn alloy was four times larger than that for the monolithic alloy due to the increased number of nucleation sites, i.e. nucleation at the interface between the reinforcing material and the α-Mg matrix as well as at the α-Mg grain boundaries.     

Application of the acoustic resonance method to evaluate the grain size of low carbon steels

The velocities and attenuations of ultrasonic waves in low carbon steels were measured precisely and automatically by the acoustic resonance method using a Lorentz-type EMAT. The attenuations were measured from the decay of a signal from the resonant vibration after stopping the external excitation at the predetermined resonant frequency, while the velocities were calculated directly from the resonant frequencies and material thicknesses. It was not possible to predict the yield strength from the velocity measurements. There was a close relationship between grain size and attenuation in the specimens which consist of ferrite and pearlite. The attenuations measured at a frequency of about 5 MHz showed a good correlation with the average grain size and yield strength. The yield strength could be evaluated within the accuracy of ±50 MPa by the acoustic resonance method. The results would be used for on-line evaluation of the grain size and the mechanical strength of steels in industry.     

Performance of the smoke extraction system for fires in the Busan–Geoje immersed tunnel

A new partial smoke extraction system for the Busan–Geoje immersed tunnel was investigated experimentally using simulated tunnel fires. The tests were performed in a 1:20-scale model tunnel with a smoke extraction duct between two traffic tubes. The fire corresponded to a 5-MW full-scale fire, based on Froude modeling. Isothermal and thermal experimental models were considered. The performance of the partial smoke extraction system was quantified under natural and longitudinal ventilation conditions. The results showed that the smoke extraction efficiency of the natural ventilation was 30% better than with longitudinal ventilation, because of smoke stratification in the tunnel. Additionally, the efficiency obtained from the thermal model was comparable to that from the isothermal model under both ventilation conditions. The results suggested that the use of a partial smoke extraction system without longitudinal ventilation improved the initial visibility during tunnel fires.     

Wind‐induced vibration control of tall buildings using hybrid buckling‐restrained braces

A buckling‐restrained brace (BRB) is a system with excellent earthquake‐proof performance, but it does not dissipate energies caused by the load from weak earthquakes or winds. A hybrid BRB (H‐BRB), which improved the performance of the BRB, is a type of composite damper system consisting of a BRB and a viscoelastic damper. To explain the wind‐induced vibration control performance of H‐BRB, a 40‐story steel building was designed and used as an analysis model in this study, on the basis of the damping ratio from a structural performance test, using normal steel braces, BRB and H‐BRB. In addition, to evaluate the optimal location of H‐BRB, a time‐history analysis of four models was conducted in the study. For such time‐history analysis, wind‐load data in a 10‐year recurrence interval, which were calculated from the wind tunnel test, were used. The result of the time‐history analysis showed that H‐BRB is effective in improving both the lateral stiffness and serviceability of a building using the existing BRB. It also confirmed that it is most effective to position H‐BRBs mainly on the lower stories. Copyright © 2012 John Wiley & Sons, Ltd.