Selective CO oxidation in the presence of hydrogen over supported Pt catalysts promoted with transition metals

Selective CO oxidation in the presence of excess hydrogen was studied over supported Pt catalysts promoted with various transition metal compounds such as Cr, Mn, Fe, Co, Ni, Cu, Zn, and Zr. CO chemisorption, XRD, TPR, and TPO were conducted to characterize active catalysts. Among them, Pt-Ni/γ-Al₂O₃ showed high CO conversions over wide reaction temperatures. For supported Pt-Ni catalysts, Alumina was superior to TiO₂ and ZrO₂ as a support. The catalytic activity at low temperatures increased with increasing the molar ratio of Ni/Pt. This accompanied the TPR peak shift to lower temperatures. The optimum molar ratio between Ni and Pt was determined to be 5. This Pt-Ni/γ A1₂O₃ showed no decrease in CO conversion and CO₂ selectivity for the selective CO oxidation in the presence of 2 vol% H₂O and 20 vol% CO₂. The bimetallic phase of Pt-Ni seems to give rise to stable activity with high CO₂ selectivity in selective oxidation of CO in H₂-rich stream.     

Absorption of chlorine into aqueous sodium carbonate solutions and desorption of carbon dioxide

The absorption of pure chlorine into aqueous sodium carbonate solutions accompanied by the desorption of carbon dioxide was studied both theoretically and experimentally. The absorption rates of chlorine and the desorption rates of carbon dioxide were measured at 25°C using a baffled agitated vessel operated batchwise. The experimental results were analyzed with the chemical absorption theory based on the Lévěque model. The measured absorption and desorption rates were in good agreement with the theoretical predictions.     

Synthesis and luminescence properties of new blue‐light‐emitting polyconjugated poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene} polymers and copolymers

Three new soluble polyconjugated polymers, all of which emitted blue light in photoluminescence and electroluminescence, were synthesized, and their luminescence properties were studied. The polymers were poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene}, poly((9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)vinylene‐1,4‐phenylene]}) [P(DOF‐PVP)], and poly([N‐(2‐ethyl) hexylcarbazole‐3,6‐diyl]‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)]vinylene‐1,4‐phenylene}). The last two polymers had alternating sequences of the two structural units. Among the three polymers, P(DOF‐PVP) performed best in the light‐emitting diode devices of indium–tin oxide/poly(ethylenedioxythiophene) doped with poly(styrene sulfonate) (30 nm)/polymer (150 nm)/Li:Al (100 nm). This might have been correlated with the balance in and magnitude of the mobility of the charge carriers, that is, positive holes and electrons, and also the electronic structure, that is, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 307–317, 2006     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

Synthesis and characterization of in situ polymerized segmented thermoplastic elastomeric polyurethane/layered silicate clay nanocomposites

Nanocomposites based on thermoplastic elastomeric polyurethane (TPU) and layered silicate clay were prepared by in situ synthesis. The properties of nanocomposites of TPU with unmodified clay were compared with that of organically modified clay. The nanocomposites of the TPU and organomodified clay showed better dispersion and exhibited superior properties. Exfoliation of the clay layers was observed at low organoclay contents, whereas an intercalated morphology was observed at higher clay contents. As one of major purposes of this study, the effect of the silicate layers in the nanocomposites on the order–disorder transition temperature (T_ODT) of the TPU was evaluated from the intensity change of the hydrogen‐bonded and free carbonyl stretching peaks and from the peak position change of the N? H bending peak. The presence of the organoclay increased T_ODT by approximately 10°C, which indicated improved stability in the phase‐separated domain structure. The layered silicate clay caused a tremendous improvement in the stiffness of the TPU; meanwhile, a reduction in the ultimate elongation was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3048–3055, 2006     

Synthesis and characterizations of a polyimide containing a triphenylamine derivative as an interlayer in polymer light-emitting diode

Polyimide containing triphenylamine derivative (TPD-PI) was synthesized to prepare a polymer interlayer having insolubility in common nonpolar solvent for light-emitting polymers. N,N′-diphenyl-N,N′-bis(4-aminophenyl)-1,1-biphenyl-4,4′-diamine, as a new triphenylamine-containing diamine monomer, was synthesized by the palladium-catalyzed amination reaction between 4-nitrodiphenylamine and 4,4′-dibromobiphenyl and subsequent reduction of the nitro-intermediate. The TPD-PI was prepared from the synthesized diamine monomer and 4,4′-(hexafluoropropylidene)-diphthalic anhydride by the standard two-step polymerization method, which involved ring-opening polymerization and subsequent cyclodehydration. The structures and properties of the monomer and the resulting polyimide were characterized with ¹H and ¹³C NMR, elemental analysis, gel permeation chromatography, UV-visible spectroscopy, etc. The TPD-PI is readily soluble in aprotic polar solvents such as N-methyl-2-pyrrolidinone and N,N-dimethylformamide and insoluble in nonpolar solvents such as toluene and xylene. The highest occupied molecular orbital (HOMO) level of the TPD-PI was measured to be 5.5 eV by a photoelectron spectrometer in air, and the band gap was calculated as 3.1 eV from the onset of UV-vis spectrum. The polymer light-emitting diode with the thin TPD-PI layer between a hole injection layer and an emitting polymer layer was fabricated to examine the performance of the polyimide as an polymer interlayer. Although the luminous efficiency of the device is lowered by the introduction of the TPD-PI interlayer, the lifetime of the device is improved.     

The effect of extrudate swell on modeling the film blowing process

The extrudate swell effect has not received sufficient attention in modeling the film blowing process. This effect is addressed in this paper, and as an ab initio study, only viscous fluids were considered. The problem region was separated into two zones; the extrudate swell zone and the film blowing zone. The annular extrudate swell problem was solved using a finite element method. The film blowing process was modeled following Pearson and Petrie's (4) work. Although only viscous fluids were considered, the simulation results show a remarkable difference when swelling was included in the modeling. Viscoelastic fluids, which are more realistic for polymer melts, were not investigated here because of the so called high Weisenberg number problem. This is an open area still under investigation.     

Numerical analysis on reaction injection molding of polyurethane foam by using a finite volume method

Foam reaction injection molding (FRIM) is one of the most popular and useful processes for producing polyurethane foam with a complex geometry. A theoretical model which includes chemical reactions, foaming, and mold filling was developed to analyze FRIM. Energy balance equation was derived by considering polyurethane reaction, water-isocyanate reaction, and evaporation of physical blowing agents. Density and viscosity model was proposed for the bubble suspension, which was assumed to be a homogeneous phase. Based on the theoretical model, three-dimensional numerical simulation for mold filling of the polyurethane foam was carried out to predict flow field, flow front advancement, and density distribution during mold filling. Mold filling of a refrigerator cavity was investigated numerically. The density and thermal conductivity of the foam in the flow front was higher than those in the initially filled region.     

Experimental analysis of bubble mode in a plate-type absorber

An experimental analysis of ammonia-water absorption was performed in a plate-type absorber. The flow of water and ammonia gas was performed in the bubble mode. The experiments were made to examine the effects of solution flow rate and gas flow rate on the performance of the absorber. It was found that the increase of solution flow rate rarely affected the mass transfer, but improved the heat transfer. As the gas flow rate increased, slugging occurred in the bubble mode and influenced the thermal boundary layer. Finally, the results were converted into dimensionless numbers to elucidate physical phenomena and plotted as Sherwood number versus Reynolds number for mass transfer performance and Nusselt number versus Reynolds number for heat transfer performance.     

Preparation and characterizations of interpenetrating polymer network hydrogels of poly(ethylene oxide) and poly(methyl methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(ethylene oxide) and poly(methyl methacrylate) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone and ethylene glycol dimethacrylate as initiators and crosslinkers, respectively. The IPN hydrogels were analyzed for sorption behavior at 25°C and at a relative humidity of 95% using dynamic vapor sorption. The IPN hydrogels exhibited a relatively high equilibrium water content in the range of 13–68%. The state of water in the swollen IPN hydrogels was investigated using differential scanning calorimetry. The free water in the hydrogels increased as the hydrophilic content increased. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 258–262, 2003