Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.     

Performance evaluation of a water/silicone oil two‐phase partitioning bioreactor using Rhodococcus erythropolis T902.1 to remove volatile organic compounds from gaseous effluents

BACKGROUND: In the framework of biological processes used for waste gas treatment, the impact of the inoculum size on the start‐up performance needs to be better evaluated. Moreover, only a few studies have investigated the behaviour of elimination capacity and biomass viability in a two‐phase partitioning bioreactor (TPPB) used for waste gas treatment. Lastly, the impact of ethanol as a co‐substrate remains misunderstood. RESULTS: Firstly, no benefit of inoculation with a high cellular density (>1.5 g L^?1) was observed in terms of start‐up performance. Secondly, the TPPB was monitored for 38 days to characterise its behaviour under several operational conditions. The removal efficiency remained above 63% for an inlet concentration of 7 g isopropylbenzene (IPB) m^?3 and at some time points reached 92% during an intermittent loading phase (10 h day^?1), corresponding to a mean elimination capacity of 4 × 10^?3 g L^?1 min^?1 (240 g m^?3 h^?1) for a mean IPB inlet load of 6.19 × 10^?3 g L^?1 min^?1 (390 g m^?3 h^?1). Under continuous IPB loading, the performance of the TPPB declined, but the period of biomass acclimatisation to this operational condition was shorter than 5 days. The biomass grew to approximately 10 g L^?1 but the cellular viability changed greatly during the experiment, suggesting an endorespiration phenomenon in the bioreactor. It was also shown that simultaneous degradation of IPB and ethanol occurred, suggesting that ethanol improves the biodegradation process without causing oxygen depletion. CONCLUSION: A water/silicone oil TPPB with ethanol as co‐substrate allowed the removal of a high inlet load of IPB during an experiment lasting 38 days. Copyright © 2008 Society of Chemical Industry     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

On Ultra-Fine Leak Detection of Hermetic Wafer Level Packages

Theoretical and practical ranges of leak rates measurable by the helium mass spectrometer are characterized. The effect of noise due to: 1) background helium present in the spectrometer and 2) desorption of helium that attaches itself to the specimen surface during bombing is quantified experimentally. The results guide a framework to extract the true leak rate from the measured leak rate profile. An optical interferometry based hermeticity measurement technique for ultra-fine leaks is proposed. The setup to implement the technique is described and a preliminary experimental result is reported.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Investigation of Mechanical and Electrical Characteristics for Cracked Conductive Particle in Anisotropic Conductive Adhesive (ACA) Assembly

In an anisotropic conductive adhesive (ACA) assembly, the electrical conduction is usually achieved with the conductive particles between the bumps of integrated circuit (IC) and corresponding conductive tracks on the glass substrate. Fully understanding of the mechanical and electrical characteristics of ACA particles can help to optimize the assembly process and improve the reliability of ACA interconnection. Most conductive particles used in the ACA assembly are with cracks in the metal coating of the particles after the ACA bonding. This paper introduced the fracture analysis by applying the cohesive elements in the numerical model of the nickel-coated polymer particle and further simulating the cracks initiation and propagation in the nickel coating during the ACA bonding. The simulation results showed that the stress distribution on the nickel-coated particle with cracks was significantly different from that on the nickel-coated particle without crack, indicating that the stress analysis by taking the crack into consideration is very important for the reliability assessment of the ACA interconnection. The stress analysis of cohesive elements indicated that the cracks initiated at the central area of the nickel coating and propagated to the polar area. Furthermore, by the introduction of a new parameter of the virtual resistance, a mathematical model was established to describe the electrical characteristics of the nickel-coated particle with cracks. The particle resistance of the nickel-coated particle with cracks was found to be much higher than that of the particle without crack in the optimized bonding pressure range, indicating that it is necessary to take the crack into consideration for the particle conduction analysis as well. Therefore, the fracture analysis on the conductive particle by taking the crack into consideration could accurately evaluate the reliability of ACA interconnection and avoid serious reliability issues.     

Optimal and self‐tuning fusion Kalman filters for discrete‐time stochastic singular systems

Based on the optimal fusion estimation algorithm weighted by scalars in the linear minimum variance sense, a distributed optimal fusion Kalman filter weighted by scalars is presented for discrete‐time stochastic singular systems with multiple sensors and correlated noises. A cross‐covariance matrix of filtering errors between any two sensors is derived. When the noise statistical information is unknown, a distributed identification approach is presented based on correlation functions and the weighted average method. Further, a distributed self‐tuning fusion filter is given, which includes two stage fusions where the first‐stage fusion is used to identify the noise covariance and the second‐stage fusion is used to obtain the fusion state filter. A simulation verifies the effectiveness of the proposed algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.