Two-phase boosted voltage generator for low-voltage DRAMs

A two-phase boosted voltage (V/sub PP/) generator circuit was proposed for use in gigabit DRAMs. It reduced the maximum gate-oxide voltage of pass transistor and the lower limit of supply voltage to V/sub PP/ and V/sub TN/, respectively, while those for the conventional charge-pump circuit are V/sub PP/+V/sub DD/ and 1.5 V/sub TN/ respectively. Also, the pumping current was increased in the new circuit. The newly proposed two-phase V/sub PP/ charge-pump circuit worked successfully at V/sub DD/ down to 0.8 V by eliminating the threshold voltage loss of the control pulse generator and was tested successfully in a 0.16-/spl mu/m test chip using triple-well CMOS technology.     

Low‐Temperature Growth of SiO2 Films by Plasma‐Enhanced Atomic Layer Deposition

Silicon dioxide (SiO₂) films prepared by plasma‐enhanced atomic‐layer deposition were successfully grown at temperatures of 100 to 250 °C, showing self‐limiting characteristics. The growth rate decreases with an increasing deposition temperature. The relative dielectric constants of SiO₂ films are ranged from 4.5 to 7.7 with the decrease of growth temperature. A SiO₂ film grown at 250 °C exhibits a much lower leakage current than that grown at 100°C due to its high film density and the fact that it contains deeper electron traps.     

Smart CMOS Image Sensor With High SBR and Subpixel Resolution for Light-Section-Based Range Finding

Light-section (LS)-based range finders are commonly used for obstacle recognition in home service robots and autonomous vehicles. This paper proposes a smart CMOS image sensor for LS-based range finding. The proposed sensor can detect the laser light, even under very strong ambient-illumination levels by using a multiple-capture frame-correlated double sampling (F-CDS), which is realized with an inverter-based switched-capacitor F-CDS accumulator. The proposed sensor also includes on-chip winner-take-all circuits that significantly reduce the software and hardware complexity of interpolation for the subpixel resolution. The prototype chip was fabricated using a 0.35-mum CMOS process. The measurement results show that the proposed sensor can detect a laser line with an intensity that is 56.5 dB lower than that of the ambient illumination, providing a spatial resolution of plusmn0.16 pixels.     

A 60-W Multicarrier WCDMA Power Amplifier Using an RF Predistorter

In this brief, we present a 60-W power amplifier that is linearized using an RF predistorter for multicarrier wideband code-division multiple-access (WCDMA) applications. The proposed RF predistorter is fully composed of RF or analog circuits, and it has a moderate memory effect compensation capability using a delayed third-order intermodulation (IM3) component path. It also includes the IM5 generation circuits and a compact IM3 generator that is capable of autocanceling for the fundamental component. The proposed RF predistorter was implemented and applied to a 60-W high-power WCDMA amplifier. For a four-carrier downlink WCDMA signal, the RF predistorter improved the adjacent channel leakage power ratio at a 5-MHz offset by 6.19 dB at an average output power of 48 dBm. The total efficiency of the system is as high as 13.6% at the same output power level. At an output power level of 60 W, the linearized power amplifier complies with the linearity specification of the WCDMA system.     

Template‐Based Reconstruction of Surface Mesh Animation from Point Cloud Animation

In this paper, we present a method for reconstructing a surface mesh animation sequence from point cloud animation data. We mainly focus on the articulated body of a subject — the motion of which can be roughly described by its internal skeletal structure. The point cloud data is assumed to be captured independently without any inter‐frame correspondence information. Using a template model that resembles the given subject, our basic idea for reconstructing the mesh animation is to deform the template model to fit to the point cloud (on a frame‐by‐frame basis) while maintaining inter‐frame coherence. We first estimate the skeletal motion from the point cloud data. After applying the skeletal motion to the template surface, we refine it to fit to the point cloud data. We demonstrate the viability of the method by applying it to reconstruct a fast dancing motion     

Enhancement of Cu nucleation in Cu-MOCVD by Pd sputtering pretreatment

Cu electroplating which emerges as a viable Cu filling technique for damascene processing relies on the presence of a smooth and continuous Cu seed layer. Metal organic chemical vapor deposition (MOCVD) may be the most promising technique to deposit the Cu seed layer. Plasma pretreatment is widely used as a precleaning technique which is essential for the enhancement of Cu nucleation in Cu-MOCVD. New pretreatment techniques which can replace plasma pretreatments are proposed in this paper. Pd sputtering, Pd–HF dipping or Pd-CVD pretreatment will possibly enhance Cu nucleation significantly if it is conducted on barrier metal films prior to Cu-MOCVD. It was found that Pd sputtering is more effective in enhancing Cu nucleation than direct plasma H₂ precleaning. Pd sputtering pretreatment is effective for a variety of barrier metals including Ta, TiN, TaN and TaSiN. The mechanism through which Cu nucleation is enhanced may be as follows: a thin Pd buffer layer formed by sputtering shields the barrier metal substrate surface with adsorbed oxygen atoms making Cu nucleation difficult and provides preferred sites for Cu nucleation.     

Self-Assembled Perovskite Nanoislands on CH3NH3PbI3 Cuboid Single Crystals by Energetic Surface Engineering

Organometal perovskite single crystals have been recognized as a promising platform for high-performance optoelectronic devices, featuring high crystallinity and stability. However, a high trap density and structural nonuniformity at the surface have been major barriers to the progress of single crystal-based optoelectronic devices. Here, the formation of a unique nanoisland structure is reported at the surface of the facet-controlled cuboid MAPbI₃ (MA = CH₃NH₃⁺) single crystals through a cation interdiffusion process enabled by energetically vaporized CsI. The interdiffusion of mobile ions between the bulk and the surface is triggered by thermally activated CsI vapor, which reconstructs the surface that is rich in MA and CsI with reduced dangling bonds. Simultaneously, an array of Cs-Pb-rich nanoislands is constructed on the surface of the MAPbI₃ single crystals. This newly reconstructed nanoisland surface enhances the light absorbance over 50% and increases the charge carrier mobility from 56 to 93 cm² V⁻¹ s⁻¹. As confirmed by Kelvin probe force microscopy, the nanoislands form a gradient band bending that prevents recombination of excess carriers, and thus, enhances lateral carrier transport properties. This unique engineering of the single crystal surface provides a pathway towards developing high-quality perovskite single-crystal surface for optoelectronic applications.     

ACAR: Adaptive Connectivity Aware Routing for Vehicular Ad Hoc Networks in City Scenarios

Multi-hop vehicle-to-vehicle communication is useful for supporting many vehicular applications that provide drivers with safety and convenience. Developing multi-hop communication in vehicular ad hoc networks (VANET) is a challenging problem due to the rapidly changing topology and frequent network disconnections, which cause failure or inefficiency in traditional ad hoc routing protocols. We propose an adaptive connectivity aware routing (ACAR) protocol that addresses these problems by adaptively selecting an optimal route with the best network transmission quality based on statistical and real-time density data that are gathered through an on-the-fly density collection process. The protocol consists of two parts: 1) select an optimal route, consisting of road segments, with the best estimated transmission quality, and 2) in each road segment of the chosen route, select the most efficient multi-hop path that will improve the delivery ratio and throughput. The optimal route is selected using our transmission quality model that takes into account vehicle densities and traffic light periods to estimate the probability of network connectivity and data delivery ratio for transmitting packets. Our simulation results show that the proposed ACAR protocol outperforms existing VANET routing protocols in terms of data delivery ratio, throughput and data packet delay. Since the proposed model is not constrained by network densities, the ACAR protocol is suitable for both daytime and nighttime city VANET scenarios.     

Design of electrically small ground planes for HF ground wave transmission

Electrically small spiral ground planes for a monopole and an electrically small antenna have been designed for HF ground wave transmission. Prototype ground planes have been built and tested. For the monopole, the transmission loss of the designed ground plane is 6 dB better than that of the same size ground radials. For the electrically small antenna, the transmission loss of the designed ground plane is 7 dB better than that of the same size solid ground plane at the antenna's operating frequency.