A thorough investigation for development of hydrogen projects from wind energy: A case study

Increasing energy demand has led to a substantial growth in the use of wind energy across the world, which can be attributed to the low initial and running costs and rapid and easy deployment of this technology. The development of hydrogen from wind energy is an excellent way to store the excess wind power produced, as the produced hydrogen can be used not only as clean fuel but also as input for various industries. Considering the good wind potentials of Yazd province, the variety of industries that are active in this area, and the central location of this province in Iran, which gives it ample access to major transport routes and other industrial hubs, hydrogen production from wind power in this province could benefit not only this region but the entire country. Given these considerations, we conducted a technical, economic, and environmental assessment of the potential for wind power generation and hydrogen production in Yazd province. Overall, the assessments showed that the best locations for harvesting wind energy in this province are Bahabad and Halvan stations. For these two stations, it is recommended to use EWT DW 52-900 turbine to take advantage of its higher nominal capacity to achieve higher electricity and hydrogen output and emission reduction. For Abarkoh and Kerit stations, which have a low wind energy potential, it is recommended to use small turbines such as Eovent EVA120 H-Darrieus. Also, economic and technical assessments showed that it is not economically justified to harvest wind energy in Ardakan station. The results of ranking the stations with the Step-wise Weight Assessment Ratio Analysis (SWARA) and Evaluation based on Distance from Average Solution (EDAS) techniques showed that Bahabad station was introduced as the best place to produce hydrogen from wind energy.     

Improving the functional properties of fish gelatin by conjugation with the water-soluble fraction of bitter almond gum

Food Science and Biotechnology - Maillard-based conjugation may be a useful way of improving the functional properties of food biopolymers. In this study, covalent attachment of fish gelatin (FG)...     

A novel low voltage very low power CMOS class AB current output stage with ultra high output current drive capability

In this paper a novel low voltage (LV) very low power (VLP) class AB current output stage (COS) with extremely high linearity and high output impedance is presented. A novel current splitting method is used to minimize the transistors gate–source voltages providing LV operation and ultra high current drive capability. High linearity and very high output impedance are achieved employing a novel resistor based current mirror avoiding conventional cascode structures to be used. The operation of the proposed COS has been verified through HSPICE simulations based on TSMC 0.18 μm CMOS technology parameters. Under supply voltage of ±0.7 V and bias current of 5 μA, it can deliver output currents as high as 14 mA with THD better than ?53 dB and extremely high output impedance of 320 MΩ while consuming only 29 μW. This makes the proposed COS to have ultra large current drive ratio (I_outmax/I_bias or the ratio of peak output current to the bias current of output branch transistors) of 2800. By increasing supply voltage to ±0.9 V, it can deliver extremely large output current of ±24 mA corresponding to 3200 current drive ratio while consuming only 42.9 μW and exhibiting high output impedance of 350 MΩ. Interestingly, the proposed COS is the first yet reported one with such extremely high output current and a THD even less than ?45 dB. Such ultra high current drive capability, high linearity and high output impedance make the proposed COS an outstanding choice for LV, VLP and high drive current mode circuits. The superiority of the proposed COS gets more significance by showing in this work that conventional COS can deliver only ±3.29 mA in equal condition. The proposed COS also exhibits high positive and negative power supply rejection ratio (PSRR+/PSRR?) of 125 dB and 130 dB, respectively. That makes it very suitable for LV, VLP mixed mode applications. The Monte Carlo simulation results are provided, which prove the outstanding robust performance of the proposed block versus process tolerances. Favorably the proposed COS resolves the major limitation of current output stages that so far has prevented designing high drive current mode circuits under low supply voltages. In brief, the deliberate combination of so many effective novel methods presents a wonderful phenomenal COS block to the world of science and engineering.     

Studying the electronic and phononic structure of penta-graphane

In this paper, we theoretically consider a two dimensional nanomaterial which is a form of hydrogenated penta-graphene; we call it penta-graphane. This structure is obtained by adding hydrogen atoms to the sp² bonded carbon atoms of penta-graphene. We investigate the thermodynamic and mechanical stability of penta-graphane. We also study the electronic and phononic structure of penta-graphane. Firstly, we use density functional theory with the revised Perdew–Burke–Ernzerhof approximation to compute the band structure. Then one–shot GW (G₀W₀) approach for estimating accurate band gap is applied. The indirect band gap of penta-graphane is 5.78 eV, which is close to the band gap of diamond. Therefore, this new structure is a good electrical insulator. We also investigate the structural stability of penta-graphane by computing the phonon structure. Finally, we calculate its specific heat capacity from the phonon density of states. Penta-graphane has a high specific heat capacity, and can potentially be used for storing and transferring energy.     

High temperature water gas shift reaction over Fe-Cr-Cu nanocatalyst fabricated by a novel method

Fe-Cr-Cu nanocatalyst was synthesized through an inorganic-precursor thermolysis approach and exploited for high temperature water gas shift reaction. The results demonstrated that the method used for the nanocatalyst fabrication led to smaller crystallite size (32.9 nm) and higher BET surface area (127.3 m²/g) compared to those of a reference sample (65.5 nm, 78.6 m²/g) prepared by co-precipitation conventional method. Furthermore, the obtained data for catalytic activity showed that the catalyst prepared via inorganic precursor has better activity than the reference sample in all studied temperatures (350-500 °C) and also exhibited higher catalytic activity than a commercial Fe-Cr-Cu catalyst in higher temperatures (more than 450 °C).     

Correlation of polymerization conditions with drag reduction efficiency of poly(1-hexene) in oil pipelines

High molecular weight with long linear side branches are frequently used in oil pipelines as one of the main classes of drag reducer agents (DRAs). We studied the effects of polymerization conditions, including reaction temperature, monomer concentration and cocatalyst concentration ratio (Al/Ti), on the polymerization yield and molecular weight of the resultant poly(1-hexene) made by Ziegler–Natta catalyst and their consequent effects on the drag reduction efficiency in a loop test. The experimental results verified that the catalyst activity increased from 115 to 220 kgPH/molTi.atm, while the molecular weight of poly(1-hexene) dropped from 2100 to 1030 kDa, as the reaction temperature was increased from 0 to 50 °C. The loop test results also revealed that the highest pressure drop was achieved using the polymer synthesized at 0 °C and by subsequent increase in reaction temperature the pressure drop decreased. Furthermore, the catalyst activity increased from 143 to 262 kgPH/molTi.atm by increasing Al/Ti ratio, while the molecular weight increased up to a maximum level of 1500 kDa at Al/Ti = 143 and decreased at higher cocatalyst contents. Similarly, the results showed the maximum pressure drop of 20 % at Al/Ti = 143. Finally, by increasing monomer concentration, the catalyst activity and polymer molecular weight increased from 75 to 262 kgPH/molTi.atm for the former, and from 700 to 1800 kDa for the latter which resulted in maximum pressure drop by 25 %. Moreover, the pressure drop for each utilized poly(1-hexene) was increased proportionately with DRA’s concentration, and interestingly enough, DRAs were further effective at more turbulent flows with higher Reynolds numbers.     

Physical and Morphological Properties of Combined Treated Wood Polymer Composites by Maleic Anhydride and Methyl Methacrylate

Wood polymer composites were prepared by consecutive impregnation with maleic anhydride (MAN) and methyl methacrylate (MMA). Samples impregnated with MAN alone, were heated at 120°C and 150°C for 4 and 8 h. Based on the Fourier transform infrared (FT-IR) analysis and soaking-drying test results, treatment with MAN at 150°C for 4 h resulted in formation of stable crosslinks. In the second stage, MMA was used for in situ polymerization within MAN-treated wood. Field emission scanning electron microscopy observation and FT-IR analysis indicated that MMA copolymerized with MAN, and the resultant polymer filled up the lumen and is also grafted on to the cell wall. Improvement of water repellency and dimensional stability were observed in the treated samples, particularly in combined treated samples. The MAN/MMA treatment improved interaction between polymer and wood.     

Stochastic models for transfer point location problem

The transfer point location problem has been introduced recently and for the case of minimax objective and planar topology, has only been studied for situations in which demand points are not weighted and have known coordinates. In this paper, we consider the case in which demand points are weighted and their coordinates have bivariate uniform distribution. Also, the problem is developed from a conceptual view and different distance measures are used to make models more applicable in real world situations. The problem is to find the best location for the transfer point such that the maximum expected weighted distance to all demand points through the transfer point is minimized. Depending on assumptions for uniform distributions, two models are considered, convexity conditions are discussed, properties of the optimal solution are obtained and methods to solve the problems are proposed. Finally, numerical examples are given.