膨胀套管的弹塑性理论分析

分析认为，膨胀套管在膨胀过程中先进入弹性阶段，然后进入弹塑性阶段，最后进入塑性流动阶段。采用弹塑性分析方法，对膨胀套管膨胀过程中套管内壁的受力与变形进行了研究，模拟了其成形的过程，并建立了解析解，为膨胀套管膨胀操作过程中确定关键操作参数提供了理论支持。根据推导出的力学模型，计算出了外径107．9mm、钢级为J55的膨胀套管膨胀到直径139．7mm时膨胀芯头拉头处的轴向力为195．94kN。     

周宁水电站工程项目管理实践

福建周宁水电站工程由闽东水电开发有限公司负责项目管理。该项目严格按照《招投标法》进行工程和设备的招标,进行了多项设计优化,注重工程质量和安全文明生产,积极开展达标投产工作,实现了进度快、质量优、投资省、效益好的管理目标。     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

PCI接口芯片s5935及其应用

s5935是AMCC公司生产的PCI接口芯片 ,可实现直通 (PASS-THRU)、邮箱 (MAILBOX)、FI FO/DMA三种工作方式。文章简要介绍了这三种工作方式 ,并给出了s5935的WDM驱动编程。     

An object replication algorithm for real-time distributed databases

A real-time distributed database system (RTDDBS) must maintain the consistency constraints of objects and must also guarantee the time constraints imposed by each request arriving at the system. Such a time constraint of a request is usually defined as a deadline period, which means that the request must be serviced on or before its time constraint. Servicing these requests may incur I/O costs, control-message transferring costs or data-message transferring costs. As a result, in our work, we first present a mathematical model that considers all these costs. Using this cost model, our objective is to service all the requests on or before their respective deadline periods and minimize the total servicing cost. To this end, from theoretical standpoint, we design a dynamic object replication algorithm, referred to as Real-time distributed dynamic Window Mechanism (RDDWM), that adapts to the random patterns of read-write requests. Using competitive analysis, from practical perspective, we study the performance of RDDWM algorithm under two different extreme conditions, i.e., when the deadline period of each request is sufficiently long and when the deadline period of each request is very short. Several illustrative examples are provided for the ease of understanding. Recommended by: Ashfaq Khokhar     

Personal telecommunication radiation safety and the precautionary principle

The approach to risk management for RF and microwave radiation has been to establish guidelines for maximum permissible levels of exposure. These guidelines are based on evaluations of the relevant scientific literature and, with safety margins to account for uncertainties and gaps in scientific knowledge, offer a significant level of protection against established hazards of RF and microwave radiation for short-term exposures. One can argue, on this basis, that the precautionary principle - specifically, safety factors -have been used to guide the making and promulgation of existing permissible-exposure standards for RF and microwave radiation. Therefore, discussions on the appropriateness of the precautionary principle for RF radiation may be "much ado about nothing". Clearly, this approach to "pre caution" neither has stifled technological development, nor has it helped to enforce the acceptance of zero risk, but it provided a basis for action when science was unable to give a clear answer.     

Graph-theoretic construction of low-density parity-check codes

This article presents a graph-theoretic method for constructing low-density parity-check (LDPC) codes from connected graphs without the requirement of large girth. This method is based on finding a set of paths in a connected graph, which satisfies the constraint that any two paths in the set are either disjoint or cross each other at one and only one vertex. Two trellis-based algorithms for finding these paths are devised. Good LDPC codes of practical lengths are constructed and they perform well with iterative decoding.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

垂直铺膜防渗技术在大堤防渗加固工程中的应用

在高水河大堤防渗加固工程中,根据堤身的实际情况,结合地质和施工条件,采用压力灌浆及砼地下连续墙相结合的方法来进行垂直铺膜防渗加固。通过对垂直铺膜前后测压管水头对比研究,分析了大堤外观干、湿土变化和大堤内干土质量密度、密实度的变化,说明了垂直铺膜防渗技术在大堤防渗应用造价低,防渗效果显著,有利于改善大堤的稳定性和安全性。垂直铺膜防渗技术应用于临时防渗及平原低水头水库和河道堤防等工程,实用性强,具有推广价值。