Simulation of an experimental compartment fire by CFD

This paper analyses the experimental results, obtained in a compartment fire experiment [Kumar R. Studies on compartment fires. Ph.D. thesis. Indian Institute of Technology, Roorkee, 2004], by using CFD modelling. Experiments were conducted in a compartment by burning methanol as a fuel. Temperatures vs. time were recorded at 11 different locations in the compartment for three sizes of fires.     

Performance modeling in critical engineering systems using RAM analysis

Reliability, availability and maintainability (RAM) analysis of system is helpful in carrying out design modifications, if any, required to achieve minimum failures or to increase mean time between failures (MTBF) and thus to plan maintainability requirements, optimize reliability and maximize equipment availability. To this effect, the paper presents the application of RAM analysis in a process industry. Markovian approach is used to model the system behavior. For carrying out analysis, transition diagrams for various subsystems are drawn and differential equations associated with them are formulated. After obtaining the steady state solution the corresponding values of reliability and maintainability are estimated at different mission times. The computed results are presented to plant personnel for their active consideration. The results proved helpful to them for analyzing the system behavior and thereby to improve the system performance considerably by adopting and practicing suitable maintenance policies/strategies.     

Progress in multimodality imaging: truly simultaneous ultrasound and magnetic resonance imaging

Multimodality medical imaging takes advantage of the strengths of different imaging modalities to provide a more complete picture of the anatomy under investigation. Many complementary modalities have been combined to form such systems and some are gaining use clinically. One combination that has not been developed, in large part due to technical difficulties, is a combined magnetic resonance (MR) and ultrasound (US) imaging system. Such a system offers the potential to combine the strengths of these modalities in a wide range of diagnostic and therapeutic applications. The goal of this study was to evaluate the feasibility of performing simultaneous multimodality US and MR imaging. An US imaging system capable of operation in a clinical MR imager was developed, and methods to perform simultaneous imaging were investigated. Simultaneous imaging was feasible without any mutual interference by either filtering the transmitted and received US signal, or by synchronizing data acquisition between the two imaging systems. Spatial registration between the two modalities was achieved by using a reference phantom with implanted glass beads in orthogonal planes. Excellent agreement was observed between spatial measurements of an object made with both modalities, and the feasibility of using this system in vivo was demonstrated in a rabbit model. Simultaneous US and MR imaging is achievable, and can provide complementary information about an object under investigation. This demonstration of technical feasibility and the development of a prototype system open up the potential to investigate the promising clinical applications of this combined technology.     

Synthesis and characterization of polysiloxanes for controlled release of 2-pyridine aldoxime–chloride

A number of polysiloxanes and their copolymers were synthesized by hydrolytic polycondensation of dialkyl (ary) dichlorosilane or their mixtures in a saturated solution of NaCl in water at low temperature (0–5°C). These polysiloxanes were characterized by intrinsic viscosity, infrared and nuclear magnetic resonance spectroscopy. 2-Pyridine aldoxime–chloride (PAM–Cl) was incorporated into these polysiloxanes, followed by crosslinking with tetraethoxysilane using dibutyltindilaurate as catalyst. The effect of pH on in vitro release rate of PAM–Cl from polysiloxane matrices was investigated in phosphate buffer of pH 3.0, 7.4, and 10.0 at 37°C using an ultraviolet spectrophotometer. Transport parameters like the order of release and diffusion coefficients for these systems (polysiloxane—PAM–Cl) were also calculated. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1837–1846, 1998     

Polymer‐induced improvements in ferroelectric liquid crystal

The chevron geometry in the SmC* phase of ferroelectric liquid crystals (FLC) has been a major obstacle in the use of FLC in displays as it results in poor electro‐optical performance. The present paper reports a novel method to overcome this problem, by doping a small amount of polymer in the FLC matrix. In addition to the improvement in smectic ordering, polymer doping is also found to be useful in improving the vital electro‐optical properties. The various electro‐optical parameters like switching time, tilt angle, contrast ratio etc. show improvement in polymer mixed guest host mixture of FLC samples. POLYM. COMPOS., 31:1776–1781, 2010. © 2010 Society of Plastics Engineers.     

Effect of Friction Stir Processing on Microstructure and Tensile Properties of an Investment Cast Al-7Si-0.6Mg Alloy

Friction stir processing (FSP) is emerging as a promising tool for microstructural modification. The current study assesses the effects of FSP on the microstructure and mechanical properties of an investment cast Al-7Si-Mg alloy. FSP eliminates porosity and significantly refines eutectic Si particles. The extent of particle refinement varied with changes in processing conditions. A high tool rotation rate and a low-to-intermediate tool traverse speed generated a higher volume fraction of finer particles. Tensile ductility changed significantly as a result of FSP, whereas ultimate tensile strength improved only marginally. Yield strength was similar in both cast and FSP samples under various heat-treated conditions, with the highest value obtained after a T6 heat treatment. Furthermore, FSP caused significant grain refinement in the stir zone, subsequently transforming into very coarse grains as abnormal grain growth occurred during solution treatment at high temperature.     

Superplastic behavior and microstructural stability of friction stir processed AZ91C alloy

Superplastic behavior of a solution treated and friction stir processed (FSP) AZ91C alloy is studied. These studies are conducted in the temperature range of 300–375 °C and strain rates (SRs) in the range of 1 × 10^?4–3 × 10^?3 s^?1. Microstructural stability of the FSP alloy is also studied in comparison to the AZ31, AZ61, and AZ91 alloys processed by various routes. High SR sensitivity in the range of 0.33–0.39 and grain size stability till 350 °C is observed for the FSP alloy. The FSP AZ91C alloy showed better thermal stability in comparison to AZ31 and AZ61 alloys. Kinetics of superplastic deformation of the FSP alloy is found to be slower as compared to AZ31 and AZ61 alloys processed by various routes, which is due to the presence of significant amount of second phase precipitates, such as, β-Mg₁₇(Al,Zn)₁₂, Mg₂Si, and Al₈Mn₅ in the FSP alloy. However, these precipitates contributed for better thermal stability of the microstructure of FSP AZ91C alloy.     

Thermoelastic study of a functionally graded annular fin with variable thermal parameters using semiexact solution

Abstract

In this paper, the thermoelastic behavior of a functionally graded material (FGM) annular fin is investigated. The material properties of the annular fin are assumed to vary radially. The heat transfer coefficient and internal heat generation are considered to be functions of temperature. A closed form solution of nonlinear heat transfer equation for the FGM fin is obtained using the homotopy perturbation method (HPM) which leads to nonuniform temperature distributions within the fin. The temperature field is then coupled with the classical theory of elasticity and the associated thermal stresses are derived analytically. For the correctness of the present closed form solution for the stress field, the results are compared with the ANSYS-based finite element method (FEM) solution. The present HPM-based closed form solution of the stress field exhibits a good agreement with the FEM results. The effect of various thermal parameters such as the thermogeometric parameter, conduction-radiation parameter, internal heat generation parameter, coefficient of variation of thermal conductivity, and the coefficient of thermal expansion on the thermal stresses are discussed. The results are presented in both nondimensional and dimensional form. The dimensional stress analysis discloses the suitability of FGM as the fin material in practical applications.     

Achieving High Strength and High Ductility in Friction Stir-Processed Cast Magnesium Alloy

Friction stir processing (FSP) is emerging as an effective tool for microstructural modification and property enhancement. As-cast AZ91 magnesium alloy was friction stir processed with one-pass and two-pass to examine the influence of processing conditions on microstructural evolution and corresponding mechanical properties. Grain refinement accompanied with development of strong basal texture was observed for both processing conditions. Ultrafine-grained (UFG) AZ91 was achieved under two-pass FSP with fine precipitates distributed on the grain boundary. The processed UFG AZ91 exhibited a high tensile strength of ~435 MPa (117 pct improvement) and tensile fracture elongation of ~23 pct. The promising combination of strength and ductility is attributed to the elimination of casting porosity, and high density of fine precipitates in an UFG structure with quite low dislocation density. The effects of grain size, precipitate, and texture on deformation behavior have been discussed.