电子警务中三维全景技术应用研究

随着信息技术的飞速发展,三维全景技术已成为电子警务中重要的组成部分。本文通过对三维全景技术特点和发展状况的介绍,提出了一套三维全景地理信息系统的应用框架,探讨了三维全景技术应用中的关键技术,并结合电子警务建设实际,详细介绍了三维全景技术在电子警务中的具体应用。可以预测,随着三维全景技术和物联网技术、云计算的集成,未来三维全景技术将成为电子警务的主流技术。     

简析组建互联局域网

随着网络的应用发展普及,用户向信息化发展的必然选择是网络的建设,局域网不仅能使信息能及时、准确地传送给每个用户,并能提供许多种应用服务。局域网组建中主要应用了网络技术中的局域网技术来建设与管理的。     

基于OpenLayers的矿场人员监控系统的研究与设计

矿区工作人员的人身安全问题和工作职责问题一直困扰着用工单位。有没有办法实时监控到矿工,又不用花费太高的成本呢?本文介绍了一种基于OpenLayers、Geoserver、J2EE的矿场人员监控的WebGIS应用的设计。     

粉末冶金TiAl合金排气门的研制

利用元素粉末冶金方法制备了TiAl合金排气阀。为提高排气门杆部的致密度、均匀度 ,设计了特有的径向热压工艺 ,并从理论上分析了与该工艺相关的压坯密度、致密化和应力变化规律。制备出高径比为 10 .7,密度为 3.79g/cm3 的粉末冶金TiAl合金汽车发动机排气门     

铍材应力常数的X射线法测试

在X2001应力分析仪上采用悬臂梁加载法测试了可以用于铍的X射线应力测试的5个衍射晶面的应力常数。结果表明,铍的5个衍射晶面的应力常数差异较大，在进行X射线应力分析时．应采用相应衍射晶面的应力常数，才能获得准确的应力分析结果。由于X射线对铍有较大的穿透深度，必须考虑X射线穿透深度对应力常数标定的影响。     

Graph-Based Dimensionality Reduction for Hyperspectral Imagery: A Review

Hyperspectral image(HSI) contains a wealth of spectral information, which makes fine classification of ground objects possible. In the meanwhile, overly redundant information in HSI brings many challenges. Specifically, the lack of training samples and the high computational cost are the inevitable obstacles in the design of classifier. In order to solve these problems, dimensionality reduction is usually adopted. Recently, graph-based dimensionality reduction has become a hot topic. In this paper, the graph-based methods for HSI dimensionality reduction are summarized from the following aspects. 1) The traditional graph-based methods employ Euclidean distance to explore the local information of samples in spectral feature space. 2) The dimensionality-reduction methods based on sparse or collaborative representation regard the sparse or collaborative coefficients as graph weights to effectively reduce reconstruction errors and represent most important information of HSI in the dictionary. 3) Improved methods based on sparse or collaborative graph have made great progress by considering global low-rank information, local intra-class information and spatial information. In order to compare typical techniques, three real HSI datasets were used to carry out relevant experiments, and then the experimental results were analysed and discussed.Finally, the future development of this research field is prospected.     

熔剂净化对Al－4．5wt％Cu合金过冷及组织的影响

采用盐类熔剂对大体积Ａｌ－４．５ｗｔ％Ｃｕ合金进行净化处理，研究了熔剂净化对Ａｌ－４．５ｗｔ％Ｃｕ合金过冷及组织的影响。通过大量的实验研究证明：粘性熔剂更能有效地去除合金中的异质核心，使合金获得较大的过冷度；随着过冷度的增大，合金的宏观组织由细小的等轴晶逐渐过渡到粗大的柱状晶，其临界转变过冷度为４０℃；二次枝晶间距随过冷度的增大而增大，其转变过冷度为５０℃。     

Simulation study on the gasification process of Ningdong coal with iron-based oxygen carrier

Chemical looping gasification (CLG) of Ningdong coal by using Fe₂O₃ as the oxygen carriers (OCs) was studied, and the gasification characteristics were obtained. A computation fluid dynamics (CFD) model based on Eulerian‐-Lagrangian multiphase framework was established, and a numerical simulation the coal chemical looping gasification processes in fuel reactor (FR) was investigated. In addition, the heterogeneous reactions, homogeneous reactions and Fe₂O₃ oxygen carriers' reduction reactions were considered in the gasification process. The characteristics of gas flow and gasification in the FR were analyzed and it was found that the experiment results were consistent with the simulation values. The results show that when the O/C mole rate was 0.5:1, the gasification temperature was 900 ℃ and the water vapor volume flow rate was 2.2 ml·min^-1, the mole fraction of syngas reached a maximum value of the experimental result and simulation value were 71.5% and 70.2%, respectively. When the O/C mole rate was 0.5:1, the gasification temperature was 900 ℃, and the water vapor volume flow was 1.8 ml·min^-1; the gasification efficiency reached the maximum value was 62.2%, and the maximum carbon conversion rate was 84.0%.     

Fouling characteristics of 90° elbow in high salinity wastewater from coal chemical industry

Due to the high salt content of coal chemical wastewater, pipeline fouling often occurs during wastewater treatment. Fouling will cause the diameter of the pipe to shrink or even block, which is not conducive to the safe and stable operation of the wastewater treatment process. In this paper, the experimental device was designed by using FLUENT software and the fouling deposition mechanisms at different flow velocities and different positions in a 90 deg bend were studied. The experimental results show that when the flow velocity is between 0.2 m·s~(-1) and 0.3 m·s~(-1), the thickness of fouling layer was positively correlated with the flow velocity; when the flow velocity is equal to 0.4 m·s~(-1), the formation of fouling is the most serious; when the flow velocity is between 0.4 m·s~(-1) and 0.7 m·s~(-1), the thickness of fouling layer was negative correlation with the flow velocity; with the increase of inlet velocity, the time for sediment point to develop into sediment surface is shortened. The fouling layer is easy to fall off because of the large shear force on the wall surface of the inner bend of the 90° elbow, so the density of sediment at this position is high.     

Importance of Low-Temperature Melt-Mixing on the Construction of Stereocomplex Crystallites with Superior Nucleation Efficiency in Asymmetric Poly(l-lactide)/Poly(d-lactide) Blends

The nucleation efficiency (NE) of stereocomplex crystallites (SCs) formed in asymmetric poly(L-lactide)/poly(D-lactide) (PLLA/PDLA) blends is generally unsatisfactory because the competition between stereocomplexation and chain mixing involved in the melt-mixing process can cause low formation efficiency and even severe aggregation of SCs. Herein, it is attempted to achieve high-efficient formation of finely dispersed SCs particles by designing a unique melt-mixing procedure, where the mixing of PLLA with 0.75 wt% PDLA is first performed at elevated temperatures (far above the melting temperature of SCs) to allow the homogeneous mixing of PLLA/PDLA chains and then at a low temperature (slightly above that of homocrystallites) to permit the full stereocomplexation of the premixed chains. It is found that the SCs formed in the blends exhibit unexpectedly low NEs (e.g., 54.5%), much inferior to that (73.6%) in the counterpart without undergoing premixing. This is because the introduction of premixing leads to a remarkable deterioration in the amount of SCs particles formed, despite decreased particle size, highlighting that the direct mixing at low temperatures of 170–180 °C (about 20–30 °C lower than that used in common melt-processing of PLA) is more effective for the construction of SCs with superior NE. The mechanisms for these striking findings are discussed.