Effects of Solvents in the Polyethylene Glycol Series on the Bonding of Copper Joints Using Ag2O Paste

The effects of reducing solvents on the bonding process using silver oxide paste in a copper joint were investigated. Three solvent types were tested: diethylene glycol (DEG), triethylene glycol (TEG), and polyethylene glycol (PEG). The strength of the joints was assessed by fracturing, which occurred at the interface of the copper oxide layer and the copper substrate in DEG and TEG samples and at the bonded interface in the PEG sample. Analysis of the samples revealed that, in the DEG and TEG samples, the copper substrate was oxidized during the bonding process, which compromised the shear strength of the joints. In contrast, the PEG sample exhibited nonuniform sintering of the silver layer while retaining good shear strength. It was found that the combination of DEG and PEG produced optimum shear strength in the copper joint, as PEG suppressed the growth of copper oxide and DEG promoted the formation of a dense sintered silver layer. The bonding strength achieved was higher than that of the gold-to-gold joint made using standard Pb-5Sn solder.     

Oral Secretions Affect HIPVs Induced by Generalist (<Emphasis Type="Italic">Mythimna loreyi</Emphasis>) and Specialist (<Emphasis Type="Italic">Parnara guttata</Emphasis>) Herbivores in Rice

Plants synthesize variable mixtures of herbivore-induced plant volatiles (HIPVs) as part of their evolutionary conserved defense. To elucidate the impact of chewing herbivores with different level of adaptation on HIPV profiles in rice, we measured HIPVs released from rice seedlings challenged by either the generalist herbivore Mythimna loreyi (MYL) or the specialist Parnara guttata (PAG). Both herbivores markedly elicited the emission of HIPVs, mainly on the second and third days after attack compared to control plants. In addition, side-by-side HIPV comparisons using MYL and PAG caterpillars revealed that generalist feeding induced comparably more HIPVs relative to specialist, particularly on day two as highlighted by multivariate analysis (PLS-DA) of emitted HIPVs, and further confirmed in mimicked herbivory experiments. Here, mechanically wounded plants treated with water (WW) released more VOCs than untreated controls, and on top of this, oral secretions (OS) from both herbivores showed differential effects on volatile emissions from the wounded plants. Similar to actual herbivory, MYL OS promoted higher amounts of HIPVs relative to PAG OS, thus supporting disparate induction of rice indirect defenses in response to generalist and specialist herbivores, which could be due to the differential composition of their OS. (196 words).     

Ultra light-weight and high-resolution X-ray mirrors using DRIE and X-ray LIGA techniques for space X-ray telescopes

We are developing novel ultra light-weight and high-resolution X-ray micro pore optics for space X-ray telescopes. In our method, curvilinear micro pore structures are firstly fabricated by silicon deep reactive ion etching (DRIE) or X-ray LIGA processes. Secondly, side walls of the micro structures are smoothed by magnetic field assisted finishing and/or hydrogen annealing techniques for high reflectivity mirrors. Thirdly, to focus parallel X-ray lights from astronomical objects, these structures are elastically or plastically bent into a spherical shape. Fourthly, the bent structures are stacked to form a multi-stage X-ray telescope. In this paper, we report on fabrication and X-ray reflection tests of silicon and nickel X-ray mirrors using the DRIE and LIGA processes, respectively. For the first time, X-ray reflections were confirmed on both of the mirrors. Estimated rms roughnesses were 5 nm and 3 nm for the silicon and nickel mirrors, respectively.     

On the role of anxiety in decisions under possiblistic uncertainty.

We focus on situations in which we must decide on what time to take an action. The action is not in question it is the time of action. We call these "time for action decisions," a prototypical example being deciding when to leave on a journey. We point out that during this type of decision process, the decision-maker recognizes two groups of forces acting on him: one that pushes him to act now and other that pushes him act later. We note that the strength of these forces depends on the information available about various uncertainties associated with the situation. It also strongly depends upon the personality of the decision-maker. We observe that as time passes these conflicting forces tend to build up an anxiety in the decision-maker resulting in an action being taken at a time of most intense anxiety. In this paper using the ideas of possibility and necessity measures to enable different interpretations of uncertain information we investigate the temporal profile of the decision-maker's anxiety as a function of their decision attitude. We investigate the role of maximization of anxiety as decision paradigm. One of our goals here is to try to understand role of the nature and the quality information plays in these types of decisions as well as its interaction with anxiety.     

Successive changes in community structure of an ethylbenzene-degrading sulfate-reducing consortium

The microbial community structure and successive changes in a mesophilic ethylbenzene-degrading sulfate-reducing consortium were for the first time clarified by the denaturing gradient gel electrophoresis (DGGE) analysis of the PCR amplified 16S rRNA gene fragments. At least ten bands on the DGGE gel were detected in the stationary phase. Phylogenetic analysis of the DGGE bands revealed that the consortium consisted of different eubacterial phyla including the delta subgroup of Proteobacteria, the order Sphingobacteriales, the order Spirochaetales, and the unknown bacterium. The most abundant band C was closely related to strain mXyS1, an m-xylene-degrading sulfate-reducing bacterium (SRB), and occurred as a sole band on DGGE gels in the logarithmic growth phase that 40% ethylbenzene was consumed accompanied by sulfide production. During further prolonged incubation, the dominancy of band C did not change. These results suggest that SRB corresponds to the most abundant band C and contributes mainly to the degradation of ethylbenzene coupled with sulfate reduction.     

Effect of anisotropic scattering in neutronics analysis of BWR assembly

The anisotropic scattering effect to keff is studied for UO₂ and MOX fueled BWR assemblies. The anisotropic scattering effect increases the assembly k_∞ by 0.44% Δk for the UO₂ assembly with 0% void fraction, and by 0.21% Δk for the MOX assembly with 0% void fraction. This is because the anisotropic scattering effect flattens the intra-assembly thermal flux, and the absorption rate in the surrounding water gap is decreased, but the absorption rates in the MOX fuel rods are increased compared to the UO₂ rods. Therefore, the total decrease in absorption rates in the UO₂ assembly is relatively large, and the k_∞ is increased in the UO₂ assembly. The dependence of the anisotropic scattering effect on the void fraction is investigated, and the significant difference of 0.62% Δk/k is found for the 0% and the 80% void fractions. The BWR assemblies with Gd rods are also considered. Furthermore, the usefulness of the transport cross section is investigated, and it is found that the transport cross section gives reasonable anisotropic scattering effect, though not satisfactory.     

MiR-10a in Pancreatic Juice as a Biomarker for Invasive Intraductal Papillary Mucinous Neoplasm by miRNA Sequencing

New biomarkers are needed to further stratify the risk of malignancy in intraductal papillary mucinous neoplasm (IPMN). Although microRNAs (miRNAs) are expected to be stable biomarkers, they can vary owing to a lack of definite internal controls. To identify universal biomarkers for invasive IPMN, we performed miRNA sequencing using tumor-normal paired samples. A total of 19 resected tissues and 13 pancreatic juice samples from 32 IPMN patients were analyzed for miRNA expression by next-generation sequencing with a two-step normalization of miRNA sequence data. The miRNAs involved in IPMN associated with invasive carcinoma were identified from this tissue analysis and further verified with the pancreatic juice samples. From the tumor-normal paired tissue analysis of the expression levels of 2792 miRNAs, 20 upregulated and 17 downregulated miRNAs were identified. In IPMN associated with invasive carcinoma (INV), miR-10a-5p and miR-221-3p were upregulated and miR-148a-3p was downregulated when compared with noninvasive IPMN. When these findings were further validated with pancreatic juice samples, miR-10a-5p was found to be elevated in INV (p = 0.002). Therefore, three differentially expressed miRNAs were identified in tissues with INV, and the expression of miR-10a-5p was also elevated in pancreatic juice samples with INV. MiR-10a-5p is a promising additional biomarker for invasive IPMN.     

Molecular Dynamics Simulation of Structural Relaxation of Asphaltene Aggregates

For asphaltene obtained from vacuum residue of Khafji crude oil, the energy-minimum conformation calculated by molecular mechanics-dynamics simulations showed that aggregated structures of asphaltene molecules through noncovalent interactions are more stable. Changes induced in aggregated structures by pretreatment with solvents were investigated using molecular dynamics calculations. The simulation showed that in quinolin at 573 K, some staking interactions could be disrupted, while, in 1-methylnaphthalene it was not observed. Autoclave experiments showed that the coke yield after pyrolysis at 713 K was decreased when the asphaltene was pretreated with quinoline at 573 K for 1 h, compared to the yield without the pretreatment. While, in the case of pretreatment in 1-methylnaphthalene, the coke yield did not change significantly. The simulation's results above can be related to the difference in coke yield between two solvents; in quinoline some aromatic-aromatic stacking interactions could be disrupted and mobility of molecules was increased. This resulted in prevention of the asphaltenes from polymerizing, as in condensation reactions among aromatic rings. Consequently, the coke yield after the pretreatment with quinoline was decreased.     

Application of Poly(acetic Acid)–Based Graft Copolymer as a Compatibilizer for Poly(L-lactic Acid)/Poly(butylenesuccinate) Blend System

Poly(L-lactic acid) (PLLA) was blended with poly(butylenesuccinate) (PBS) using a single-screw extruder to modify the poor characteristics of these polymers. Furthermore, when both polymers were blended, the graft copolymer that was synthesized by partially saponified poly(vinyl alcohol) (PSPVA) and ?-caprolactone (?-CL) was used as a novel compatibilizer. The structure of the synthesized compatibilizer was determined by ¹H or ¹³C NMR. From this result, the ring-opening polymerization of the ?-CL occurred at the hydroxyl group of PSPVA. The structures of the PLLA/PBS solvent-cast blended films could be observed via an optical microscope. From the optical microscopic observation, the structures of the solvent-cast blended films with the synthesized compatibilizer were more homogeneous than those of the solvent-cast blended films without the compatibilizer. The mechanical properties of the PLLA/PBS extruded blended films were determined by a tensile test. The result showed the tensile strength of the blended films with the synthesized compatibilizer was greater than that of the blended films without the compatibilizer.     

Thermal deformation measurement of the solder joints in electronic packages using electron moiré method

In this paper, electron moiré method is used to measure the thermal deformation of electronic packages. In order to observe the electron moiré fringe, a holographic grid was replicated on the cross section of the BGA type package at 150°C. This grid was fabricated on a glass plate using a moving point holographic system, and was replicated to measured area at high temperature. Under SEM, the holographic grid(specimen grid) and a programmed electron beam scan(master grid) interfere and form electron moiré patterns. The shear strain measurement technique using electron moiré method is described. Using the electron moiré method, the shear strains in the different solder joints were measured and analysed. Some useful results were obtained.