用于X光激光实验的反射式线聚焦光学系统的设计和分析

基于三维光线追迹的象差计算,对卢瑟福实验室用离轴球面反射线聚焦系统作了分析。然后,首次提出了用于X光激光实验的两类新的反射式线聚焦构型,即反射式光楔列阵和光锥列阵系统,并作了计算。最后,对所得结果作了比较和讨论。     

铯原子激光共振电离

用Ｎｄ：ＹＡＧ及其泵浦的染料激光进行铯原子三步共振电离。求解了非饱和共振过程速率方程，计算出基态和激发态共振吸收截面，给出电离效率分别与激发电离速率以及作用时间的变化关系，得到饱和激发电离的流量条件和通量条件。     

多层多跨铰接框架计算

本文采用柔度矩阵法,对多层多跨铰接框架进行静力与动力分析,附有实例。与刚度法相比,其优点是使矩阵降价,方法实用,可应用于工业厂房和一般刚架设计中。     

Generalized Gabor expansions of discrete-time signals in l2(Z) via biorthogonal-like sequences

In this paper, a biorthogonal-like sequences (BLS) theory and its application to the generalized Gabor expansions (equivalently, the generalized short-time Fourier transform/filterbank summation) are presented. A pair of BLS's are defined to be two sequences satisfying a biorthogonal-like condition (BLC), which is a moment equation and equivalent to a linear difference equation. We show that two collections in a Hilbert space generated by a pair of BLS's in the joint time-frequency domain are complete, either can be used as an analysis filter, and the other can be used as a synthesis filter for a generalized Gabor expansion of discrete-time signals. A sufficient and necessary condition on the existence of BLS's based on the moment equation is presented, which is simpler to use than frame theory. Given a filter generating a frame, its BLS's also generate frames. The dual frame is one of them. Given a FIR analysis/synthesis filter, there is a FIR synthesis/analysis filter if BLS's exist. The algorithm to compute FIR analysis and synthesis filters based on the linear difference equation is presented in this paper, which is simpler than frame operator     

28Cr2Mo1VA钢变速冷却转变动力学研究

用膨胀法对28Cr2Mo1VA钢测定了变速冷却过冷奥氏体转变动力学曲线,结果表明,先慢冷后快冷,珠光体、贝氏体转变滞后;反之,转变超前。并提出用图解计算法求转变点,结果与实验相符合。     

COIL中BHP浓度对发生O_2(~1△)的影响

本文实验研究了BHP的浓度对产生O2（1△）的影响。实验结果表明：当BHP浓度大于3.5M时，Cl2利用率以及O2（1△）的产率将不依赖于BHP浓度的变化而变化，同时，实验结果表明，使用低浓度的BHP对COIL的操作是可行的。     

用线性状态观测器重构交流矢量控制系统中的负载扰动

在异步电动机磁场定向数学模型的基础上,给出了恒磁条件下异步电动机的解耦模型及传动系统的线性状态方程,并提出了重构负载扰动转矩的线性状态观测器。利用重构的负载转矩在矢量控制系统中进行扰动前馈,明显地提高了系统的抗负载扰动能力,从而为进一步提高矢量控制系统的动态性能开辟了一条有效的途径。     

Plasma immersion ion implantation for SOI synthesis: SIMOX and ion-cut

We have demonstrated feasibility to form silicon-on-insulator (SOI) substrates using plasma immersion ion implantation (PIII) for both separation by implantation of oxygen and ion-cut. This high throughput technique can substantially lower the high cost of SOI substrates due to the simpler implanter design as well as ease of maintenance. For separation by plasma implantation of oxygen wafers, secondary ion mass spectrometry analysis and cross-sectional transmission electron micrographs show continuous buried oxide formation under a single-crystal silicon overlayer with sharp Si/SiO₂ interfaces after oxygen plasma implantation and high-temperature (1300°C) annealing. Ion-cut SOI wafer fabrication technique is implemented for the first time using PIII. The hydrogen plasma can be optimized so that only one ion species is dominant in concentration and there are minimal effects by other residual ions on the ion-cut process. The physical mechanism of hydrogen induced silicon surface layer cleavage has been investigated. An ideal gas law model of the microcavity internal pressure combined with a two-dimensional finite element fracture mechanics model is used to approximate the fracture driving force which is sufficient to overcome the silicon fracture resistance.     

Structure and damping properties of polydimethylsiloxane and polymethacrylate sequential interpenetrating polymer networks

By using the technology of the sequential interpenetrating polymer network, a series of novel damping materials based on a polydimethylsiloxane (PDMS)/polyacrylate (PAC) matrix with polymethacrylate (PMAC) were synthesized. They have a controllable broad transition peak spanning the temperature range of 150–220°C and the medial value of loss factor with maximum of 0.35–0.60. Dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and atomic force microscopy (AFM) were applied to analyze and characterize the transition behavior and the microphase structure of the materials. It was found that the size and height of a transition peak at both the low‐ and the high‐temperature zones change as a function not only of the concentration of PMAC and PDMS but also of the kind of PMAC; simultaneously, the low‐ temperature behavior was also governed by the crystallization of PDMS. The content of the crosslinking agent exerts a significant influence on the configuration of the curves of the transition peaks. AFM shows a characteristic phase morphology of double‐phase continuity containing a transition layer and domain less than 1 μm, indicating that the interwoven multilayer networks are the key to incorporation of the immiscible components and form a broad damping functional region. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 545–551, 2002