Photoluminescence enhancement by isolating β-FeSi2 layers from defective layers

We have investigated an optimal annealing process in order to enhance 1.55 μm light emission from semiconducting β-FeSi₂ and found that two steps annealing at 600 °C and 800 °C is effective to its enhancement. Rutherford backscattering spectroscopy and SEM observations revealed that pronounced surface segregation of Fe atoms during annealing at 600 °C caused surface precipitate of β-FeSi₂. The enhancement of light emission is attributed spatial isolation of the surface β-FeSi₂ (light emitting layer) from damaged and defective layers with nonradiative recombination centers.     

A Gait Phase Measurement System Using Treadmill Motor Current

The article describes the development of a gait phase time-based split-belt treadmill measurement system. Conventional methods of measuring gait phase, such as the foot switch and force plate, require significant preparation and are costly. In this article, we propose a simple, cheap, and accurate gait phase measurement system that utilizes only the treadmill motor current value. Comparison of this algorithm with conventional methods reveals that the proposed algorithm is as accurate as the foot switch. Moreover, the proposed algorithm can estimate stance phase within a 0.2?s error of the measured value of the force plate in most cases (four out of five healthy subjects). This accuracy is higher than that of the foot switch which is widely used in the clinical field.     

Application of wavelet transform for extracting edges of paddy fields from remotely sensed images

For geographical information systems (GIS) to be useful in the management of Japanese paddy fields, it is vital to be able to prepare base maps that define sections of field. We attempted to prepare a base map by detecting the edges of submerged paddy fields from a SPOT image with the use of multi-resolution wavelet transform. The raw image of SPOT band 3 was decomposed into a low frequency approximation image and a set of high frequency detailed images to five levels, and then reconstructed. The reconstructed image at the fifth level was obtained from all of the high frequency images except for the low frequency approximation image. The image reconstructed up to full scale was then applied to a zero-crossing scheme and three post-processings—line thinning, removal of isolated pixels, and connection of pixels with their neighbours—in order to obtain clear edges. The spatial features of the image indicating the edges obtained by multi-resolution wavelet transform were compared quantitatively with those obtained by using a difference of Gaussian (DOG) filter. The multi-resolution wavelet transform was better than the DOG filter in that the base map obtained by the wavelet transform method represented a ‘field block’, which is typically composed of 10 holdings of paddy field, more precisely than with the DOG filter, and in that the number of open polygons on this map was smaller, indicating that the wavelet transform method is more suitable for producing the base map in GIS for the management of paddy fields.     

A multilevel PWM strategy suitable for high‐voltage motor direct drive systems with consideration of the adverse effect of dead time

Recently, high‐voltage motor direct drive systems have been put to practical use, and various multilevel PWM strategies have also been proposed. This paper describes a multilevel PWM strategy [our group calls it the Carrier Phase Selection Method (CPS)] that has the lowest line voltage harmonic distortion in order to prevent the degradation of high‐voltage motor winding insulations. This method takes the adverse effect of dead time into consideration, and it controls the shift direction of a carrier phase. Therefore, a favorable output waveform without instantaneous voltage surges is achieved even if the line voltage level changes. Moreover, the switching transitions across all switching devices are well‐balanced, so the utilization of inverter unit cells is equalized. This is an important factor when designing the entire system. Based on simulation and experimental results, it is shown that this CPS method is particularly effective in high‐voltage motor direct drive systems. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(2): 77–88, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20474     

Single-fluorophore imaging with an unmodified epifluorescence microscope and conventional video camera

Single fluorophores in aqueous solution were imaged in real time with a conventional silicon-intensified target video camera connected to an unmodified commercial microscope (IX70, Olympus) with epifluorescence excitation with a high-pressure mercury lamp. Neither a powerful laser nor an extremely sensitive video camera was required. Three experimental systems were used to demonstrate quantitatively that individual, moving or stationary Cy3 fluorophores could be imaged with the microscope: Cy3-gelsolin attached to an actin filament sliding over heavy meromyosin, sliding actin filaments sparsely labelled with Cy3, and heavy meromyosin labelled with one or two Cy3 fluorophores. The results should encourage many laboratories to attempt 'single-molecule physiology' in which the functions and mechanisms of molecular machines are studied at the single-molecule level in an environment where the biological machines are fully active.     

Structural analysis of polyacenic semiconductor (PAS) materials with Xenon NMR measurements

Structural analysis of the polyacenic semiconductor (PAS) material prepared by the pyrolysis of phenol-formaldehyde resin at relatively low temperature (680 °C) has been performed by applying ¹²⁹Xe nuclear magnetic resonance (NMR) measurements. One can obtain information on the microporous structure of the PAS material through adsorption of Xe atoms, since a ¹²⁹Xe nucleus is a very sensitive probe of its microscopic environment. All the introduced Xe atoms were adsorbed on the internal surface of the pure PAS sample, which indicated remarkably large surface area of the PAS material. The average pore size of the pure PAS sample has been determined to be 7.7 ± 1.6 Å from the pressure dependence of the Xe NMR chemical shift. In connection with the application of the PAS material to the electrode of the Li rechargeable battery, changes in the Xe NMR spectrum brought about by extrinsic additives such as binder, electrolyte solvent, and the doped Li have been investigated. In particular, it has been found that the Li-doping entirely prevents Xe atoms from entering into the micropores of the PAS material, probably due to adsorption of the solvent molecules on the internal surface of the micropores.