可编程计算器辅助测量施工放线

昌马水库工程是甘肃省重点工程，在施工中对测量放线要求较高，为了提高放线精度及效率，在放线中引入可编程序的casio fk一4500P计算器配合，迅速处理放线数据，取得了可喜的效果。     

Fabrication and characteristics of high-speed implant-confined index-guided lateral-current 850-nm vertical cavity surface-emitting lasers

Process technology of high-speed implant-apertured index-guide lateral-current-injection top dielectric-mirror quantum-well 850-nm vertical cavity surface-emitting lasers (VCSELs) has been developed. Oxygen and helium implantation for aperture definition and extrinsic capacitance reduction, dielectric mirror formation, p- and n-ohmic contact formation, VCSEL resistance, and thermal analysis were investigated. Employing this technology, GaAs/AlGaAs-based 850-nm VCSELs with small signal modulation bandwidths up to 11.5 Gb/s and an eye diagram generated at 12 Gb/s by a pseudorandom bit sequence of 2/sup 31/-1 were achieved. The bit-error rates were below 10/sup -13/. The threshold current is as low as 0.8 mA for 7-/spl mu/m-diameter current apertures and typical slope efficiencies of 0.45-0.5 mA/mW were obtained.     

添加CaF2-YF3的AlN陶瓷的热导率

用CaF2和YF3做添加剂，在1750℃制备了热导率高于170W/m.K的的AlN陶瓷，并用XRD和SEM研究了AlN陶瓷在烧结过程中的相组成，微结构以及晶格参数的变化，并讨论了其对热导率的影响，研究发现，当使用CaF2-YF3做添加剂时，微结构差异对AlN陶瓷热导率的影响很小，AlN陶瓷的热导率主要由AlN晶格氧缺陷浓度决定，由于CaF2-YF3能有效降低AlN颗粒表面的氧含量，从而有利于获得高的热导率。     

液压系统污染控制的研究内容及其相互关系

介绍了国内外液压系统污染控制研究工作的发展现状及其所涉及的研究内容,并予以分类和归纳。     

天然“药品”——蜂胶

主要介绍了蜂胶的营养成分、分类、质量标准、提取方式及保健功能。     

坑道用水下堵漏剂的研制

坑道水下堵漏剂的研制包括F－1、F－2和F－3型。其中F－1是一种有机堵漏剂，它可以在水中固化；F－2是一种无机防水堵漏剂，施工方便；F－3是速凝型，它可在瞬间固化，能对坑道的涌水口进行堵漏。     

Speed–accuracy tradeoff in Fitts’ law tasks—on the equivalency of actual and nominal pointing precision

Pointing tasks in human–computer interaction obey certain speed–accuracy tradeoff rules. In general, the more accurate the task to be accomplished, the longer it takes and vice versa. Fitts’ law models the speed–accuracy tradeoff effect in pointing as imposed by the task parameters, through Fitts’ index of difficulty (I_d) based on the ratio of the nominal movement distance and the size of the target. Operating with different speed or accuracy biases, performers may utilize more or less area than the target specifies, introducing another subjective layer of speed–accuracy tradeoff relative to the task specification. A conventional approach to overcome the impact of the subjective layer of speed–accuracy tradeoff is to use the a posteriori “effective” pointing precision W_e in lieu of the nominal target width W. Such an approach has lacked a theoretical or empirical foundation. This study investigates the nature and the relationship of the two layers of speed–accuracy tradeoff by systematically controlling both I_d and the index of target utilization I_u in a set of four experiments. Their results show that the impacts of the two layers of speed–accuracy tradeoff are not fundamentally equivalent. The use of W_e could indeed compensate for the difference in target utilization, but not completely. More logical Fitts’ law parameter estimates can be obtained by the W_e adjustment, although its use also lowers the correlation between pointing time and the index of difficulty. The study also shows the complex interaction effect between I_d and I_u, suggesting that a simple and complete model accommodating both layers of speed–accuracy tradeoff may not exist.     

银川市室内环境空气污染现状及治理措施的初探

本文通过对银川市室内环境空气污染现状的调查与检测,阐述了室内环境空气污染的来源及危害,提出了污染治理措施。     

工字梁的抗剪极限承载力

对工字梁腹板抗剪极限承载力的研究进行总结,对各种公式与文献中的试验结果进行对比,将拉力场理论和转向应力场理论的假定与ANSYS分析揭示的腹板应力发展变化规律进行对比,指出了假定和数值分析结果的不一致。提出了翼缘对腹板转动约束的合理参数,得到精度良好的考虑翼缘约束的腹板剪切屈曲系数。利用得到的屈曲系数,考虑翼缘抗弯承载力的贡献,提出新的工字梁抗剪极限承载力的计算公式。与现有试验数据和ANSYS非线性有限元分析结果的对比,证实建议方法离散性较小,适用范围广,尤其是对于通用高厚比较大的梁,较以往方法有了较大改进。