Adhesion studies of tyre cords with rubber. I. Synthesis and characterization of natural rubber graft copolymers

Glycidyl methacrylate and N-vinyl pyrrolidone have been grafted onto natural rubber at 32°C using the simultaneous cobalt-60 irradiation technique. The natural rubber samples were swollen in the monomers for 24 h and thereafter subjected to gamma irradiation. The homopolymers formed in the graft copolymerization reactions and unreacted monomer were removed by solvent extraction using acetone and methanol for glycidyl methacrylate and N-vinyl pyrrolidone monomer, respectively. The influence of total dose and monomer concentration on the graft parameters was investigated. The dependence of the rate of grafting on the monomer concentration was found to be 0.93 and 0.80 for glycidyl methacrylate and N-vinyl pyrrolidone, respectively. DSC and TGA studies of the polymers were undertaken. Grafted copolymers based on glycidyl methacrylate were relatively less thermally stable compared with ungrafted natural rubber.     

Preparation and characterization of low-halogen and nonhalgoen fire-resistant low-smoke (FRLS) cable sheathing compound from blends of functionalized polyolefins and PVC

An attempt is made to develop a novel series of cable sheathing compounds with variation in chlorine content and sufficient fire retardance and unique low-smoke characteristics. These are prepared by blending PVC and functionalized polyolefins in different compositions. PE and EPDM have been functionalized by grafting dibutyl maleate (DBM) using DCP as initiator. FRLS compounds made from PVC-functionalized polyolefin blends possess the special characteristics of low-smoke, low-acid-gas generation, increased fire retardance, and improved volume resistivity, which are much better in comparison with a typical PVC sheathing compound. Thermoplastic elastomer (TPE) based nonhalogen FRLS compounds are also reported. The mechanisms for grafting, polymer-polymer and polymer-filler interactions have been presented.     

Anisotropy of X-ray structural parameters of the three phase model in cellulose I

Anisotropy of X-ray structural parameters of the three phase model proposed by Mitra and Mukherjee (ref.2), has been investigated in the case of cellulose fibres of ramie, hemp and jute. The structural parameters have been determined separately from each of the observable equatorial reflections. It has been found that the parameter degree of crystallinity as defined in the model is in fact anisotropic at least in the samples studied. The parameter degree of paracrystallinity introduced by Mitra and Mukherjee was also found to be anisotropic. Several important correlations between the structural parameters have been drawn. It has been observed, in agreement with the recent findings of Hosemann and Balta Calleja (ref.10) that the greater the paracrystalline distortion, the smaller the ‘paracrystallite size’.     

Energy Efficiency of Two‐Phase Mixing in a Modified Bubble Column

Energy efficiency for gas liquid mixing in a modified downflow bubble column reactor has been analyzed in this paper. Efficiencies of the different parts of the bubble column have been assessed on the basis of energy dissipation. Prediction of the energy dissipation coefficient as well as energy utilization efficiency due to gas‐liquid mixing as a function of different physical, geometric and dynamic variables of the system has been done by correlation method. The distribution of energy utilization in the different zones of the column has also been analyzed. Experiments were carried out with air‐water and air‐aqueous solutions of carboxy methyl cellulose with different concentrations.     

Pixel rearrangement based statistical restoration scheme reducing embedding noise

In this paper, a block based steganographic algorithm has been proposed where a sequence of secret bits are embedded into a set of pixels by rearranging the pixel locations. This algorithm has been devised as an improvement over existing statistical restoration based algorithms in order to reduce the additive noise which occurs due to embedding. It is shown that the proposed scheme substantially reduces the additive noise compared to existing statistical restoration based schemes.     

Numerical simulations of drop impact and spreading on horizontal and inclined surfaces

The phenomenon of drop spreading is important to several process engineering applications. In the present work, numerical simulations of the dynamics of drop impact and spreading on horizontal and inclined surfaces were carried out using the volume of fluid (VOF) method. For the horizontal surfaces, the dynamics of impact and spreading of glycerin drops on wax and glass surfaces was investigated for which the experimental measurements were available [Šikalo, Š., Tropea, C., Ganic, E.N., 2005a. Dynamic wetting angle of a spreading droplet. Experimental Thermal and Fluid Science 29, 795-802; Šikalo, Š., Tropea, C., Ganic, E.N., 2005b. Impact of droplets onto inclined surfaces. Journal of Colloid and Interface Science 286, 661-669]. The influence of surface wetting characteristics was investigated by using static contact angle (SCA) and dynamic contact angle (DCA) models. The dynamics of drop impact and spreading on inclined surfaces and the different regimes of drop impact and spreading process were also investigated. In particular, the effects of surface inclination, surface wetting characteristics, liquid properties and impact velocity on the dynamics of drop impact and spreading were investigated numerically and the results were verified experimentally. It was found that the SCA model can predict the drop impact and spreading behavior in quantitative agreement with the experiments for less wettable surfaces (SCA>90^°). However, for more wettable surfaces (SCA<90^°), the DCA observed at initial contact times were order of magnitude higher than SCA values and therefore the DCA model is needed for the accurate prediction of the spreading behavior.     

Synthesis and densification of magnesium aluminate spinel: effect of MgO reactivity

Stoichiometric magnesium aluminate spinel was synthesized by reaction sintering of alumina with caustic and sintered magnesia. The volume expansion of 5–7% during MgAl₂O₄ formation was utilized to identify the starting temperature of spinel formation and densification by high temperature dilatometry. The magnesia reactivity was determined by measurement of crystallite size and specific surface area. Caustic magnesia and sintered magnesia behave differently vis-à-vis phase formation and densification of spinel. Densification of stoichiometric Mag-Al spinel was carried out between 1650 and 1750 °C. Attempts were made to correlate the MgO reactivity with microstructure and densification of spinel.     

Microstructure and properties of flame sprayed tungsten carbide coatings

This article reports on feasibility experiments carried out with oxy-acetylene spray system with various oxygen to fuel ratios using two different tungsten carbide powders and powder feeding methods, to evaluate the newly developed fused WC, synthesised by transferred arc thermal plasma method. Transferred arc thermal plasma method is more economical and less energy intensive than the conventional arc method and results in a fused carbide powder with higher hardness. The microstructure and phase composition of powders and coatings were analysed by optical and scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Carbon content of the powders and coatings were determined to study the decarburisation of the material during spraying process. Coatings were also characterised by their hardness and abrasive wear. The effects of metallurgical transformation and phase content are related to wear performance. The results demonstrate that the powders exhibit various degree of phase transformation during the spray process depending on the type of powder, powder feeding and spray parameters. The carbon loss during the spray process in excess of 45% resulted in reduced hardness and wear resistance of the coatings. Coatings with high amount of WC and W₂C along with FeW₃C showed higher wear resistance. Thus, coatings of high wear resistance can be produced using fused tungsten carbide powder with WC and W₂C phases, which can be economically synthesised by thermal plasma transferred arc method.     

Propagation of correlations in local random quantum circuits

We derive a dynamical bound on the propagation of correlations in local random quantum circuits—lattice spin systems where piecewise quantum operations—in space and time—occur with classical probabilities. Correlations are quantified by the Frobenius norm of the commutator of two positive operators acting on disjoint regions of a one-dimensional circular chain of length L. For a time \(t=O(L)\), correlations spread ballistically to spatial distances \(\mathcal {D}=t\), growing at best, diffusively with time for any distance within that radius with extensively suppressed distance- dependent corrections. For \(t=\varOmega (L^2)\), all parts of the system get almost equally correlated with exponentially suppressed distance- dependent corrections and approach the maximum amount of correlations that may be established asymptotically.