Nanocomposite piezoelectric films of P(VDF‐TrFE)/LiNbO3

Piezoelectric films were prepared by incorporation of lithium niobate (LiNbO₃) nanoparticles into copolymer of vinylidene difluoride and trifluoroethylene. Nanoparticles of LiNbO₃ with ferroelectric phase were successfully synthesized and dispersed homogenously by ultrasonication in the copolymer matrix without any surfactant or surface functionalization. The nanocomposites were fully characterized by electronic microscopy, X‐ray diffraction, differential scanning calorimetry, dynamical mechanical analysis, and piezometer. Surprisingly, the copolymer matrix crystallinity and morphology were not affected by the incorporation of nanoparticles. Therefore the nanocomposites remained good mechanicals properties and high ferroelectricity coupled to nonlinear optical activity thanks to the noncentro symmetric space group of lithium niobate. This could be a novel approach to develop new multifunctional materials. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Enhancement of fibroblastic proliferation from photoreactive starch with immobilized epidermal growth factor

Carboxymethyl starch was modified by the incorporation of an azidophenyl group to prepare photoreactive starch, and characterized by Fourier transform infrared reflectance (FT‐IR), proton nuclear magnetic resonance (¹H‐NMR), and ultraviolet (UV) spectroscopy. Photo‐irradiation immobilized the Az‐starch on a polystyrene plate and it was stably retained on the surface. The protein containing immobilized Az‐starch was also immobilized on a stripe micropatterned plate. UV irradiation time and Az‐starch concentration were used to alter the physical properties of Az‐starch and consequently control the rate of epidermal growth factor (EGF) release. The Az‐starch that released growth factor was not cytotoxic to 3T3‐L1 fibroblast cells, and the immobilized EGF maintained its activity and induced cellular proliferation in vitro. These results suggest that Az‐starch could be useful as a clinical synthetic material for medical applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of a Shroud Tube on Flow Field and Particle Behavior Inside a Bag-Filter Vessel

A shroud tube was used to decrease the amount of particles toward the bag filters from whole particles entering a filter vessel. The effects of the shroud tube on the flow field and particle behavior inside the vessel were studied. The air mixed with dust particles enters the vessel through a tangential inlet duct. Some of the particles are deposited on the inside wall of the vessel and the surface of the shroud tube. The other ones are collected on the filter surface or passed through it. The particles deposited on the wall surfaces fall into a hopper by gravity, and those collected on filters are removed by back pulse-jet flow. Computational simulation was performed to know the prereduction rate of particles by deposition on the wall surfaces for the different shroud tubes. The experiment was accomplished with some shroud tubes suggested by the results of computational simulation, and the experimental results were compared qualitatively with the computational results. The shroud tube blocked the direct transport of particles toward the bag filters and reduced the particle loading onto the filters. The particle loading was reduced when the upper region of the vessel was not blocked by the shroud tube more than when the vessel was blocked wholly with the filters from the upper end wall. However, the re-entrainment of the particles removed from the filters by the back pulse cleaning increased when the upper region of the vessel was not blocked by the shroud tube more than when the vessel was blocked wholly with the filters from the upper end wall.     

Polypyrrole composite membrane with high permeability prepared by interfacial polymerization

Novel polypyrrole (PPy)/polydimethylsiloxane (PDMS) composite membrane was prepared by interfacial polymerization to make a very effective gas separation membrane. We found that Polymerized PPy films as thin as ～200 nm could be chemically synthesized as freestanding membranes by using the interfacial polymerization technique. Additionally, we show that difference morphology of PPys films was obtained by controlling polymerization rate and more dense films were formed at low polymerization rate. Wide X-ray diffraction study showed the d spacing value of the PPy film decreased from 4.89 å to 3.67 å by the rate of polymerization decreases. According to d spacing value decrease, selectivity of a PPy composite membrane was increased dramatically and permeability was reduced gradually. This high selectivity was derived from d spacing closed to the kinetic diameter of nitrogen. These results indicated that the permeability is controlled by the diffusion coefficient, reflecting the packed structure of the PPy film. The highest selectivity value of composite membrane that was prepared by interfacial polymerization was O₂/N₂=17.2 and permeability for O₂ was 40.2 barrer.     

Effect of Sintering Temperature on Thermoelectric Properties of p‐Bi2Te3 Alloys Produced by Gas Atomization

In this research, p‐type Bi₂Te₃–75% Sb₂Te₃ thermoelectric alloy powders were produced by gas atomization and subsequently sintered by hot pressing at different temperatures. The grain growth of the hot‐pressed samples was observed with increasing sintering temperature from 380°C to 460°C. The compressive strength increased with increasing hot‐pressing temperature due to the high relative density of bulk samples obtained at high temperatures. The effect of sintering temperature on thermoelectric (TE) properties was studied. The maximum power factor 3.48 mW/mK² was obtained for the sample hot pressed at 420°C due to the resulting high electrical conductivity and enhanced Seebeck coefficient values.     

关于Filon算法的一点注记

本文对谐波分析中数值积分的Filon公式提出了一点改进,改进后的算法在微机上得到实现,经实算表明,计算结果满足工程精度要求。     

A general procedure to synthesize highly crystalline metal oxide and mixed oxide nanocrystals in aqueous medium and photocatalytic activity of metal/oxide nanohybrids

A conventional and general route has been exploited to the high yield synthesis of many kinds of highly crystalline metal oxide and mixed oxide nanocrystals with different morphologies including belt, rod, truncated-octahedron, cubic, sphere, sheet via the hydrothermal reaction of inorganic precursors in aqueous solution in the presence of bifunctional 6-aminohexanoic acid (AHA) molecules as a capping agent. This method is a simple, reproducible and general route for the preparation of a variety of high-crystalline inorganic nanocrystals in scale-up. The shape of inorganic nanocrystals such as CoWO(4), La(2)(MoO(4))(3) can be controlled by simply adjusting the synthesis conditions including pH solution and reaction temperature. Further, by tuning precursor monomer concentration, the mesocrystal hierarchical aggregated microspheres (e.g., MnWO(4), La(2)(MoO(4))(3)) can be achieved, due to the spontaneous assembly of individual AHA-capped nanoparticles. These obtained AHA-capped nanocrystals are excellent supports for the synthesis of a variety of hybrid metal/oxide nanocrystals in which noble metal particles are uniformly deposited on the surface of each individual nanosupport. The photocatalytic activity of Ag/TiO(2) nanobelts as a typical hybrid photocatalyst sample for Methylene Blue degradation was also studied.     

Site-selective substitution and resulting magnetism in arc-melted perovskite ATiO3-δ (A = Ca,Sr, Ba)

Magnetic properties in perovskite titanates ATiO_3-δ (A = Ca, Sr, Ba) were investigated before and after arc melting. Crystal structure analysis was conducted by powder synchrotron X-ray diffraction with Rietveld refinements. Quantitative chemical element analysis was carried out by X-ray photoelectron spectroscopy. Magnetic measurements were conducted by vibrating sample magnetometer and X-ray magnetic circular dichroism (XMCD). The magnetic properties are found to be affected by impurities of 3d elements such as Fe, Co, and Ni. Depending on the composition and crystal structure, the occupation of the magnetic ions in perovskite titanates is selectively varied, which is interpreted to be the origin of the different magnetic behaviors in arc-melted perovskite titanates ATiO_3-δ (A = Ca, Sr, Ba). In addition, both formation of oxygen vacancies and the reduction of Ti⁴⁺ to Ti³⁺ during arc-melting also play a role as proven by XMCD. Nevertheless, preferential site occupation of magnetic impurities is dominant in the magnetic properties of arc-melted perovskite ATiO_3-δ (A = Ca, Sr, Ba).     

Interfacial tension measurement between immiscible polymers: improved deformed drop retraction method

This paper describes an improvement of the technique to measure interfacial tension in immiscible polymer blends. Our method is based on the droplet retraction method, in which one relates the kinetics of relaxation of a deformed droplet to the interfacial tension between the matrix and droplet. Previously, the problem with this technique has been the difficulty in preparing axisymmetric ellipsoidal droplets. In our work, we demonstrate that perfect axisymmetric ellipsoidal droplets are produced at a later stage of relaxation of short imbedded fibers. With this technique, we utilize the strengths of both the deformed droplet method and the imbedded fiber retraction method while overcoming their shortcomings. The interfacial tension value thus obtained was compared to that by conventional methods. Additionally, the effect of confinement by external walls on the interfacial tension measurement was studied. Confinement affects interfacial tension measurement when the gap between the walls is less than two times the equilibrium drop size.