On Testing Prebond Dies with Incomplete Clock Networks in a 3D IC Using DLLs

3D integration of ICs is an emerging technology where multiple silicon dies are stacked vertically. The manufacturing itself is based on wafer-to-wafer bonding, die-to-wafer bonding or die-to-die bonding. Wafer-to-wafer bonding has the lowest yield as a good die may be stacked against a bad die, resulting in a wasted good die. Thus the latter two options are preferred to keep yield high and manufacturing costs low. However, these methods require dies to be tested separately before they are stacked. A problem with testing dies separately is that the clock network of a prebond die may be incomplete before stacking. In this paper we present a solution to address this problem. The solution is based on on-die Delay Lock Loop (DLL) implementations that are only activated during testing prebond unstacked dies to synchronize disconnected clock regions. A problem with using DLLs in testing is that they cannot be turned on or off within a single cycle. Since scan-based testing requires that test patterns be scanned in at a slow clock frequency before fast capture clocks are applied, On-Product Clock Generation (OPCG) must be used. The proposed solution addresses the above problems and allows a prebond with an incomplete clock network to be tested with low skew.     

Crystallization kinetics of Sn40Se60 thin films for phase change memory applications

The crystallization kinetics of Sn₄₀Se₆₀ thin films has been successfully investigated using sheet resistance versus temperature measurements. Thermal evaporation was used to deposit the films on ordinary glass substrates. The crystallization temperature for Sn₄₀Se₆₀ thin film was found to be 156.6 ± 0.3 ℃. In the as-deposited state, the sheet resistance was found to be 195 MΩ, this value declined to 1560 Ω/口 upon annealing. The value of activation energy obtained from the Kissinger plot was 0.62 ± 0.07 eV. From the results obtained, Sn₄₀Se₆₀ is a promising alloy for PCM application because of its high electrical contrast, high crystallization temperature, and relatively high activation energy.     

Silk proteins for biomedical applications: Bioengineering perspectives

Biomaterials of either natural or synthetic origin are used to fabricate implantable devices, as carriers for bioactive molecules or as substrates to facilitate tissue regeneration. For the design of medical devices it is fundamental to use materials characterized by non-immunogenicity, biocompatibility, slow and/or controllable biodegradability, non-toxicity, and structural integrity. The success of biomaterial-derived biodevices tends to be based on the biomimetic architecture of the materials. Recently, proteins from natural precursors that are essentially structural and functional polymers, have gained popularity as biomaterials. The silks produced by silkworms or spiders are of particular interest as versatile protein polymers. These form the basis for diverse biomedical applications that exploit their unique biochemical nature, biocompatibility and high mechanical strength. This review discusses and summarizes the latest advances in the engineering of silk-based biomaterials, focusing specifically on the fabrication of diverse bio-mimetic structures such as films, hydrogels, scaffolds, nanofibers and nanoparticles; their functionalization and potential for biomedical applications.     

Analytic method for thermal performance and optimization of an absorber plate fin having variable thermal conductivity and overall loss coefficient

The absorber of a collector receives solar energy which is delivered to the transport medium to be carried away as useful energy. During this process, temperature of the absorber plate increases and therefore, thermophysical parameters engaged to determine the thermal performance of an absorber plate varies with temperature of the plate. The present study demonstrates analytically to determine the performance of an absorber plate fin with temperature dependent both thermal conductivity and overall heat loss coefficient. The decomposition method is proposed for the solution methodology. An optimum design analysis has also been carried out. A comparative study has been executed among the present results and that of existed in the published work, and a notable difference in results has been found. Finally, unlike published work, dependency parameters on the performances and optimum design have been highlighted.     

Cognitive radio CDMA networking with spectrum sensing

In this paper, the performance of cognitive radio (CR) code division multiple access (CDMA) systems is analyzed. More precisely, CR users belong to a cognitive radio network (CRN), which coexists with a primary radio network (PRN). Both CRN and PRN are CDMA‐based, with colocated base stations. Soft hand off and power control are considered in both the CRN and the PRN. Upon the development of an accurate simulator for a representative three‐cell cellular scenario, we evaluate the performance of the proposed CR system in terms of outage probability, blocking probability and average data rate of secondary users. Three different spectrum sensing techniques are. Two new schemes, based on interference limit, are proposed and compared with an existing adaptive spectrum sensing scheme. Spectrum activity measurements and spectrum sharing decisions have been considered for evaluating the performance of the three schemes. The paper proposes a new CR‐CDMA networking model and a simulation testbed for evaluating performances of secondary users and primary users in terms of outage, blocking, BER and average data rate in the presence of soft hand‐off and power control. For comparison purposes, the analysis in the absence of spectrum sensing is also investigated.Copyright © 2012 John Wiley & Sons, Ltd.     

Isolation and identification of phosphate‐solubilizing microorganisms and distribution of orthophosphate in different seasons from sewage‐fed East Kolkata Wetland

This study focused on isolation and identification of possible phosphate‐solubilizing bacteria (PSB ) from the sewage‐fed East Kolkata Wetland (EKWL ), a prospective water resource for pisciculture. In addition, different limnological parameters have been correlated with orthophosphate and seasonal variations. PSB have been isolated in Pikovskaya medium and identified morphologically and biochemically and finally analysed by 16S rDNA gene sequence. Limnological studies involving temperature (potentiometric), pH (potentiometric), dissolved oxygen (iodometric), ammonia‐nitrogen (spectrophotometric) and orthophosphate (spectrophotometric) concentrations were conducted. The results of this study established the presence of Bacillus megaterium , a potential PSB in EKWL . The activity of B. megaterium is also supported by the seasonal orthophosphate variations. The changes in concentration of other limnological parameters were also prominent. The water quality parameters of temperature (r  = 0.886), dissolved oxygen (r  = 0.729) and ammonia‐nitrogen (r  = 0.396) concentrations exhibited a positive correlation with orthophosphate and a negative correlation with pH (r  = ?0.699). The B. megaterium obtained in this study, exhibited a significant alteration in regard to orthophosphate content and relationships with other factors. Further experiment on the soluble phosphorus solubilization potential of B. megaterium revealed the biological availability of phosphorus was increased by threefold after 120 hr of incubation, with the decreasing pH value, although the phytase activity was 0.419 U/ml. PSB have a vital function in plant nutrition in supplying phosphate, essential nutrients and its uptake results in appropriate functioning and metabolism of different aquatic plants and organisms. PSB are competent biofertilizer to amplify aquaculture production for sustainable development.     

ISGP: Iterative sequential geometric programming for precise and robust CMOS analog circuit sizing

In this paper, a fast yet accurate CMOS analog circuit sizing method, referred to as Iterative Sequential Geometric Programming (ISGP), has been proposed. In this methodology, a correction factor has been introduced for each parameter of the geometric programming (GP) compatible device and performance model. These correction factors are updated using a SPICE simulation after every iteration of a sequential geometric programming (SGP) optimization. The proposed methodology takes advantage of SGP based optimization, namely, fast convergence and effectively optimum design and at the same time it uses SPICE simulation to fine tune the design point by rectifying inaccuracy that may exists in the GP compatible device and performance models. In addition, the ISGP considers the requirement of common centroid layout and yield aware design centering for robust final design point specifying the number of fingers and finger widths for each transistor which makes the design point ready for layout.