Effect of amino functionalized MWCNT on the crosslink density,fracture toughness of epoxy and mechanical properties of carbon–epoxy composites

Amino functionalized multiwalled carbon nanotubes (A-MWCNTs) reinforced two phase (A-MWNT–epoxy) and three phase (A-MWCNTs–carbon fiber–epoxy) nanocomposites were fabricated with 0.25 wt%, 0.5 wt% and 1.0 wt% loadings of A-MWCNTs. It is observed that, A-MWCNTs can improve the crosslink density of epoxy significantly. Fracture toughness of epoxy matrix is found to increase up to an optimum crosslink density improvement, indicating the role of crosslink density in imparting toughness to epoxy apart from the crack deflection contributions of A-MWCNTs. In addition to that, this study infers that, tensile, flexural properties of the three phase composites are strongly influenced by the fracture toughness changes of the matrices. This study, thus proposes additional mechanisms of toughness enhancements for two phase and mechanical properties enhancements for three phase composites imparted by A-MWCNTs.     

Behavioral study of alumina nanoparticles in pool boiling heat transfer on a vertical surface

Experiments were carried out to investigate the pool boiling of alumina‐water nanofluid at 0.1 g/l to 0.5 g/l of distilled water, and the nucleate pool boiling heat transfer of pure water and nanofluid at different mass concentrations were compared at and above the atmospheric pressure. At atmospheric pressure, different concentrations of nanofluids display different degrees of deterioration in boiling heat transfer. The effect of pressure and concentration of nanoparticles revealed significant enhancement in heat flux and deterioration in pool boiling. The heat transfer coefficient of 0.5 g/l alumina‐water nanofluid was compared with pure water and clearly indicates deterioration. At all pressures the heat transfer coefficients of the nanofluid were lower than those of pure water. Experimental observation revealed particles coating over the heater surface and subsequent SEM inspection of the heater surface showed nanoparticles coating on the surface forming a porous layer. To substantiate the nanoparticle deposition and its effect on heat flux, investigation was done by measuring the surface roughness of the heater surface before and after the experiment. While SEM images of the heater surface revealed nanoparticle deposition, surface roughness of the heater surface confirmed it. Based on the experimental investigations it can be concluded that an optimum thickness of nanoparticles coating favors an increase in heat flux. Higher surface temperature due to the presence of nanoparticles coating results in the deterioration of boiling heat transfer. © 2011 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20365     

Passive building energy savings: A review of building envelope components

A significant portion of the total primary energy is consumed by today's buildings in developed countries. In many of these buildings, the energy consumption can be significantly reduced by adopting energy efficiency strategies. Due to environmental concerns and the high cost of energy in recent years there has been a renewed interest in building energy efficiency. This article strives to make an exhaustive technical review of the building envelope components and respective improvements from an energy efficiency perspective. Different types of energy efficient walls such as Trombe walls, ventilated walls, and glazed walls are discussed. Performance of different fenestration technologies including aerogel, vacuum glazing and frames are presented. Advances in energy efficient roofs including the contemporary green roofs, photovoltaic roofs, radiant-transmittive barrier and evaporative roof cooling systems are discussed. Various types of thermal insulation materials are enumerated along with selection criteria of these materials. The effects of thermal mass and phase change material on building cooling/heating loads and peak loads are discussed. Application of thermal mass as an energy saving method is more effective in places where the outside ambient air temperature differences between the days and nights are high. Air tightness and infiltration of building envelopes are discussed as they play a crucial role in the energy consumption of a building. Energy efficiency approaches sometimes might not require additional capital investment. For example, a holistic energy efficient building design approach can reduce the size of mechanical systems compensating the additional cost of energy efficiency features.     

Processing and characterization of solid and microcellular PHBV/PBAT blend and its RWF/nanoclay composites

Solid and microcellular components made of poly (3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)/poly (butylene adipate-co-terephthalate) (PBAT) blend (weight ratio of PHBV:PBAT = 30:70), recycled wood fiber (RWF), and nanoclay (NC) were prepared via a conventional and microcellular-injection molding process, respectively. Morphology, thermal properties, and mechanical properties were investigated. The addition of 10% RWF (both untreated and silane-treated) reduced the cell size and increased the cell density of the microcellular components. Also, the addition of 10% RWF (both untreated and silane-treated) generally increased the specific Young’s modulus and tensile strength, but decreased the specific toughness and strain-at-break in both solid and microcellular components. Moreover, unlike the neat PHBV/PBAT blend, microcellular PHBV/PBAT/RWF (both untreated and silane-treated) composites showed higher specific toughness and strain-at-break compared to their solid counterparts. In addition, higher specific toughness and strain-at-break was observed in the PHBV/PBAT/untreated-RWF composite compared with the PHBV/PBAT/silane-treated RWF composite, particularly in the microcellular components. The degree of PHBV crystallinity increased significantly in both solid and microcellular PHBV/PBAT/RWF composites although the degree of PHBV crystallinity in the solid components was slightly higher than that of their microcellular counterparts. The effects of adding 2% nanoclay on the properties of the PHBV/PBAT/silane-treated-RWF composite were also investigated. The nanoclays exhibited an intercalated structure in the composites based on XRD analysis and did not induce significant changes in the cell morphology and mechanical properties of the PHBV/PBAT/silane-treated-RWF composite. However, it did improve its thermal stability.     

Deposition of diamond/β-SiC nanocomposite films onto a cutting tool material

The motivation behind depositing nanocrystalline diamond/β-SiC composite thin films onto a cutting tool material is not only to obtain films having a whole range of combined properties of the components but also to enhance their fracture toughness without compromising on the hardness aspect. Nanocrystalline diamond composites are expected to behave differently owing to the large volume of grain boundaries. With smooth surface morphology and improved adhesion, diamond/β-SiC nanocomposite film system may not only serve as a separate film system but may also serve as an interlayer for the further deposition of adherent diamond top layers with regard to cutting tool applications. In this paper we report the deposition of nanocrystalline diamond/β-SiC composite thin films onto WC-6 wt.% Co substrates by employing microwave plasma chemical vapor deposition (MWCVD) technique using gas mixtures of H₂ and CH₄ and tetramethylsilane [TMS, Si(CH₃)₄]. Scanning electron microscopy (SEM), glancing angle X-ray diffraction (GIXRD), energy-dispersive X-ray (EDX), micro Raman scattering and Fourier transform infrared (FTIR) spectroscopic analyses have been carried out to characterize the microstructure and composition of the deposited films. The microstructure of the composite films constitutes a phase mixture of nanometer sized diamond and β-SiC grains. By adjusting TMS gas flow during deposition, β-SiC content in the nanocomposite films can be controlled. This aspect was utilized to successfully realize diamond/β-SiC nanocomposite gradient films with diamond top layers on the hard metal substrates in a single process step.     

Polylactide‐pine wood flour composites

Biobased and biodegradable polylactide (PLA)‐pine wood flour (PWF) composites were investigated as a means to reduce the overall material cost and tailor the material properties. The composites were prepared using a kinetic‐mixer and an injection molding machine. The tensile modulus of the PLA‐PWF composites increased with the PWF content whereas the toughness and strain‐at‐break decreased. The tensile strength remained the same irrespective of the PWF content (up to 40%). The storage modulus also increased with the PWF content. Additionally, composites containing PWF treated with silane showed higher storage modulus than those without the silane treatment. The area integration underneath the tan δ peaks decreased with increasing PWF, indicating that the PLA‐PWF composites exhibited more elastic behavior with increasing PWF. The degree of crystallinity of the PLA‐PWF composites increased significantly with the PWF content. Furthermore, the treatment of PWF with silane had a positive effect on its nucleating ability, as treated PLA‐PWF composites showed higher crystallinity compared with their untreated counterparts. The morphology of the fracture surfaces were studied using a scanning electron microscope. Finally, a Halpin‐Tsai analytical model to predict Young's modulus of PLA‐PWF composites was presented to compare the theoretical results with that of experimental results. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Thermally induced transformations of amorphous carbon nanostructures fabricated by electron beam induced deposition

We studied the thermally induced phase transformations of electron-beam-induced deposited (EBID) amorphous carbon nanostructures by correlating the changes in its morphology with internal microstructure by using combined atomic force microscopy (AFM) and high resolution confocal Raman microscopy. These carbon deposits can be used to create heterogeneous junctions in electronic devices commonly known as carbon-metal interconnects. We compared two basic shapes of EBID deposits: dots/pillars with widths from 50 to 600 nm and heights from 50 to 500 nm and lines with variable heights from 10 to 150 nm but having a constant length of 6 μm. We observed that during thermal annealing, the nanoscale amorphous deposits go through multistage transformation including dehydration and stress-relaxation around 150 °C, dehydrogenation within 150-300 °C, followed by graphitization (>350 °C) and formation of nanocrystalline, highly densified graphitic deposits around 450 °C. The later stage of transformation occurs well below commonly observed graphitization for bulk carbon (600-800 °C). It was observed that the shape of the deposits contribute significantly to the phase transformations. We suggested that this difference is controlled by different contributions from interfacial footprints area. Moreover, the rate of graphitization was different for deposits of different shapes with the lines showing a much stronger dependence of its structure on the density than the dots.     

Reversible tuning of plasmon coupling in gold nanoparticle chains using ultrathin responsive polymer film

We demonstrate large and reversible tuning of plasmonic properties of gold nanoparticles mediated by the reversible breaking and making of linear and branched chains of gold nanoparticles adsorbed on an ultrathin (1 nm) responsive polymer film. Atomic force microscopy revealed that at pH below the isoelectric point of the polybase (extended state of the polymer chains), gold nanoparticles adsorbed on the polymer layer existed primarily as individual nanoparticles. On the other hand, at higher pH, the polymer chains transition from coil to globule (collapsed) state, resulting in the formation of linear and branched chains with strong interparticle plasmon coupling. Reversible aggregation of the nanoparticles resulted in large and reversible change in the optical properties of the metal nanostructure assemblies. In particular, we observed a large redistribution of the intensity between the individual and coupled plasmon bands and a large shift (nearly 95 nm) in the coupled plasmon band with change in pH. Large tunability of plasmonic properties of the metal nanostructure chains reported here is believed to be caused by the chain aggregates of nanoparticles and un-cross-linked state of the adsorbed polymer enabling large changes in polymer chain conformation.     

Towards the prioritization of system test cases

During software development, companies are frequently faced with lack of time and resources, which limits their ability to effectively complete testing efforts. This paper presents a system‐level, value‐driven approach to test case prioritization called the Prioritization of Requirements for Test (PORT). PORT involves analysing and assigning value to each requirement using the following four factors: requirements volatility, customer priority, implementation complexity, and fault proneness. System test cases are prioritized such that the test cases for requirements with higher priority are executed earlier during system test. PORT was applied to four student team projects as well as an industrial case study. The results show that PORT improves the rate of detection of severe failures over random prioritization. Additionally, the results indicate that customer priority was the most important contributor towards improved rate of failure detection. Copyright © 2013 John Wiley & Sons, Ltd.