X-ray based tools for the investigation of buried interfaces in organic electronic devices

X-ray reflectivity combined with grazing incidence diffraction is a valuable tool for investigating organic multilayer structures that can be used in devices. We focus on a bilayer stack consisting of two materials (poly-(3-hexylthiophene)) (P3HT) and poly-(4-styrenesulfonic acid) (PSSA) spin cast from orthogonal solvents (water in the case of PSSA and chloroform or toluene for P3HT). X-ray reflectivity is used to determine the thickness of all layers as well as the roughness of the organic–organic hetero-interface and the P3HT surface. The surface roughness is found to be consistent with the results of atomic force microscopy measurements. For the roughness of P3HT/PSSA interface, we observe a strong dependence on the solvent used for P3HT deposition. The solvent also strongly impacts the texturing of the P3HT crystallites as revealed by grazing incidence diffraction. When applying the various PSSA/P3HT multilayers in organic thin-film transistors, we find an excellent correlation between the determined interface morphology, structure and the device performance.     

Thermal oxidation for crystalline silicon solar cells exceeding 19% efficiency applying industrially feasible process technology

Thermal oxides are commonly used for the surface passivation of high‐efficiency silicon solar cells from mono‐ and multicrystalline silicon and have led to the highest conversion efficiencies reported so far. In order to improve the cost‐effectiveness of the oxidation process, a wet oxidation in steam ambience is applied and experimentally compared to a standard dry oxidation. The processes yield identical physical properties of the oxide. The front contact is created using a screen‐printing process of a hotmelt silver paste in combination with light‐induced silver plating. The contact formation on the front requires a short high‐temperature firing process, therefore the thermal stability of the rear surface passivation is very important. The surface recombination velocity of the fired oxide is experimentally determined to be below S ≤ 38 cm/s after annealing with a thin layer of evaporated aluminium on top. Monocrystalline solar cells are produced and 19·3% efficiency is obtained as best value on 4 cm² cell area. Simulations show the potential of the developed process to approach 20% efficiency. Copyright © 2008 John Wiley & Sons, Ltd.     

Thermal parameters identification of micrometric layers of microelectronic devices by thermoreflectance microscopy

The objective of this paper is the determination of the thermal properties of micrometric layers of electronic devices using a thermoreflectance probe. Unlike classical thermoreflectance methods, the main point of the method presented in this paper is to be able to quantify the heating energy (by Joule effect) and the effective temperature response (by calibration). It is then possible to estimate the thermal conductivity (in W m⁻¹ K⁻¹) instead of the thermal diffusivity (in m² s⁻¹). A semi-analytical thermal 3D-periodic model then enables to identify a few thermal properties of the layers of the device, and in particular the thermal conductivity of the passivation layer. This methodology has been applied to the study of an industrial device containing interconnect test structures made of copper lines on a silicon wafer with a few micrometers BCB (BenzoCycloButene) polymer passivation layer. The BCB thermal conductivity and the metal heat capacity are obtained using this method.     

Covalent Adaptable Microstructures via Combining Two-Photon Laser Printing and Alkoxyamine Chemistry: Toward Living 3D Microstructures

Manufacturing programmable materials, whose mechanical properties can be adapted on demand, is highly desired for their application in areas ranging from robotics, to biomedicine, or microfluidics. Herein, the inclusion of dynamic and living bonds, such as alkoxyamines, in a printable formulation suitable for two-photon 3D laser printing is exploited. On one hand, taking advantage of the dynamic covalent character of alkoxyamines, the nitroxide exchange reaction is investigated. As a consequence, a reduction of the Young´s Modulus by 50%, is measured by nanoindentation. On the other hand, due to its “living” characteristic, the chain extension becomes possible via nitroxide mediated polymerization. In particular, living nitroxide mediated polymerization of styrene results not only in a dramatic increase of the volume (≈8 times) of the 3D printed microstructure but also an increase of the Young's Modulus by two orders of magnitude (from 14 MPa to 2.7 GPa), while maintaining the shape including fine structural details. Thus, the approach introduces a new dimension by enabling to create microstructures with dynamically tunable size and mechanical properties.     

ATM‐based wireless broadband access in the local loop

Broadband networks using wireless transmission techniques are a quick and flexible means of implementing subscriber access. Unoccupied frequency bands with sufficient bandwidth to allow the transmission of digital signals at very high bit rates are found only in the microwave bands. Because the path loss is fairly high at these frequencies, the diameter of radio cells is limited to a maximum of a few kilometres. This results in a microcellular system, which is best implemented in the form of a point‐to‐multipoint system, where one radio‐base station serves all subscribers registered in that radio cell. An interactive, broadband, ATM‐based radio local loop has undergone successful trials in Munich. Copyright © 2001 John Wiley & Sons, Ltd.     

Optical Interconnects on and in Printed Circuit Boards

Two types of short distance optical interconnects for on-board applications are presented: Small diameter plastic optical fibre (POF) links and multimode polymer waveguide layers integrated in multilayer printed circuit boards (PCB). POF links with fibre numbers up to 128 and link lengths up to 50 cm are realized with total transmission loss values below 2 dB at 660 nm. First tests of 10 cm long temperature stable multimode polymer waveguides laminated into standard multilayer PCBs demonstrate the capabilities of combined electrical-optical circuit boards.     

Gallium gradients in Cu(In,Ga)Se2 thin‐film solar cells

The gallium gradient in Cu(In,Ga)Se₂ (CIGS) layers, which forms during the two industrially relevant deposition routes, the sequential and co‐evaporation processes, plays a key role in the device performance of CIGS thin‐film modules. In this contribution, we present a comprehensive study on the formation, nature, and consequences of gallium gradients in CIGS solar cells. The formation of gallium gradients is analyzed in real time during a rapid selenization process by in situ X‐ray measurements. In addition, the gallium grading of a CIGS layer grown with an in‐line co‐evaporation process is analyzed by means of depth profiling with mass spectrometry. This gallium gradient of a real solar cell served as input data for device simulations. Depth‐dependent occurrence of lateral inhomogeneities on the µm scale in CIGS deposited by the co‐evaporation process was investigated by highly spatially resolved luminescence measurements on etched CIGS samples, which revealed a dependence of the optical bandgap, the quasi‐Fermi level splitting, transition levels, and the vertical gallium gradient. Transmission electron microscopy analyses of CIGS cross‐sections point to a difference in gallium content in the near surface region of neighboring grains. Migration barriers for a copper‐vacancy‐mediated indium and gallium diffusion in CuInSe₂ and CuGaSe₂ were calculated using density functional theory. The migration barrier for the In_Cu antisite in CuGaSe₂ is significantly lower compared with the Ga_Cu antisite in CuInSe₂, which is in accordance with the experimentally observed Ga gradients in CIGS layers grown by co‐evaporation and selenization processes. Copyright © 2014 John Wiley & Sons, Ltd.     

Oblivious Transfers and Privacy Amplification

Oblivious transfer (OT) is an important primitive in cryptography. In chosen one-out-of-two string OT, a sender offers two strings, one of which the other party, called the receiver, can choose to read, not learning any information about the other string. The sender on the other hand does not obtain any information about the receivers choice. We consider the problem of reducing this primitive to OT for single bits. Previous attempts to doing this were based on self-intersecting codes. We present a new technique for the same task, based on so-called privacy amplification. It is shown that our method has two important advantages over the previous approaches. First, it is more efficient in terms of the number of required realizations of bit OT, and second, the technique even allows for reducing string OT to (apparently) much weaker primitives. An example of such a primitive is universal OT, where the receiver can adaptively choose what type of information he wants to obtain about the two bits sent by the sender subject to the only constraint that some, possibly very small, uncertainty must remain about the pair of bits.