Template‐Confined Dewetting Process to Surface Nanopatterns: Fabrication,Structural Tunability,and Structure‐Related Properties

Metallic surface nanopatterns are prepared by a template‐confined dewetting process with multiple structural controllabilities. The morphology of the building blocks is homogeneous throughout the surface nanopatterns, as the dewetting process proceeds separately in each bowl. The features of the building units in the surface patterns are highly dependent on the annealing temperature. Importantly, the size and composition of the nanoparticles in the surface nanopatterns can be pre‐calculated and designed by manipulating the thickness of the evaporated metallic films. The heating temperature and composition of the building units influence the surface‐enhanced Raman scattering (SERS) and plasmonic properties, thus tuning the localized surface plasmon resonance peaks over a broad range (from visible to near infrared). The introduction of silver in the gold surface nanopatterns enhances the SERS performance dramatically. This work not only provides a powerful route to fabricate surface nanopatterns, but also supplies a platform to study the mechanism of the complicated dewetting processes of metals.     

Doping efficiency and energy-level scheme in C60F48-doped zinc–tetraphenylporphyrin films

High resolution synchrotron-based core level spectroscopy was used to examine the energy level alignment at the interface of zinc–tetraphenylporphyrin films doped by the surface acceptor C₆₀F₄₈. Two distinct fluorofullerene charge states were identified, corresponding to ionized and neutral molecules, and their relative concentration as a function of coverage was used to evaluate the probability of occupation of the acceptor lowest unoccupied molecular orbital (LUMO). From an initial acceptor energy of ?0.25 eV, the C₆₀F₄₈ LUMO shifts upwards with coverage due to a doping-induced interfacial dipole potential, and stabilization of the LUMO at an energy 0.45 eV above the Fermi energy was obtained. While the energy difference upon saturation is consistent with the results obtained for other donor–acceptor systems that have been interpreted as Fermi level pinning, the present work shows that the energy offset is a direct consequence of the interplay between Fermi–Dirac statistics in combination with the interfacial dipole potential.     

Analysis of a 26 756 bp segment from the left arm of yeast chromosome IV

The nucleotide sequence of a 26·7 kb DNA segment from the left arm of Saccharomyces cerevisiae chromosome IV is presented. An analysis of this segment revealed 11 open reading frames (ORFs) longer than 300 bp and one split gene. These ORFs include the genes encoding the large subunit of RNA polymerase II, the biotin apo-protein ligase, an ADP-ribosylation factor (ARF 2), the ‘L35’-ribosomal protein, a rho GDP dissociation factor, and the sequence encoding the protein phosphatase 2A. Further sequence analysis revealed a short ORF encoding the ribosomal protein YL41B, an intron in a 5′ untranslated region and an extended homology with another cosmid (X83276) located on the same chromosome. The potential biological relevance of these findings is discussed. The sequence was submitted to the EMBL database under Accession Number X96876.     

22 nm光刻技术前景

在国际半导体技术蓝图(ITRS)指定的22nm节点中[1],该产业将在两种竞争的光刻解决方案中进行选择,这将取决于其产品的发展路线图。在某些情况下,业界甚至可能会同时使用两种方案。这两种竞争方案就是极紫外光刻技术(EUVL)和32nm节点由193nm浸没式双重图形光刻(DPL)扩展到多图形的光刻技术。讨论了两种技术,比较了两种技术所需的关键解决方案的现状,以及存在的挑战。     

OFDM with reduced peak-to-average power ratio by multiple signal representation

In this paper two highly effective, flexible and distortionless peak power reduction schemes for orthogonal frequency division multiplexing (ofdm) with low amount of additional complexity and almost vanishing redundancy are presented. The schemes work with arbitrary numbers of subcarriers and signal sets. The first approach generates a set of several alternative multicarrier signals and selects that transmit signal with the lowest peak power value. The second method optimally combines partial transmit sequences to minimize the peak-to-average power ratio (PAR-coefficient). The schemes are analyzed theoretically and their performance is covered by simulations.     

Molecularly‐Engineered, 4D‐Printed Liquid Crystal Elastomer Actuators

Three‐dimensional structures that undergo reversible shape changes in response to mild stimuli enable a wide range of smart devices, such as soft robots or implantable medical devices. Herein, a dual thiol‐ene reaction scheme is used to synthesize a class of liquid crystal (LC) elastomers that can be 3D printed into complex shapes and subsequently undergo controlled shape change. Through controlling the phase transition temperature of polymerizable LC inks, morphing 3D structures with tunable actuation temperature (28 ± 2 to 105 ± 1 °C) are fabricated. Finally, multiple LC inks are 3D printed into single structures to allow for the production of untethered, thermo‐responsive structures that sequentially and reversibly undergo multiple shape changes.     

Chiral Excitonic Organic Photodiodes for Direct Detection of Circular Polarized Light

A facile route to soft matter self‐powered bulk heterojunction photodiode detectors sensitive to the circular polarization state of light is shown based on the intrinsic excitonic circular dichroism of the photoactive layer blend. As light detecting materials, enantiopure semiconducting small molecular squaraine derivates of opposite handedness are employed. Via Mueller matrix ellipsometry, the circular dichroism is proven to be of H‐type excitonic nature and not originating from mesoscopic structural ordering. Within the green spectral range, the photodiodes convert circular polarized light into a handedness‐dependent photocurrent with a maximum dissymmetry factor of ±0.1 corresponding to 5% overall efficiency for the polarization discrimination under short circuit conditions. On the basis of transfer matrix optical simulations, it is rationalized that the optical dissymmetry fully translates into a photocurrent dissymmetry for ease of device design. Thereby, the photodiode's ability to efficiently distinguish between left and right circularly polarized light without the use of external optical elements and voltage bias is demonstrated. This allows a straightforward and sustainable future design of flexible, lightweight, and compact integrated platforms for chiroptical imaging and sensing.     

Evaluation of optimization methods for nonrigid medical image registration using mutual information and B-splines.

A popular technique for nonrigid registration of medical images is based on the maximization of their mutual information, in combination with a deformation field parameterized by cubic B-splines. The coordinate mapping that relates the two images is found using an iterative optimization procedure. This work compares the performance of eight optimization methods: gradient descent (with two different step size selection algorithms), quasi-Newton, nonlinear conjugate gradient, Kiefer-Wolfowitz, simultaneous perturbation, Robbins-Monro, and evolution strategy. Special attention is paid to computation time reduction by using fewer voxels to calculate the cost function and its derivatives. The optimization methods are tested on manually deformed CT images of the heart, on follow-up CT chest scans, and on MR scans of the prostate acquired using a BFFE, T1, and T2 protocol. Registration accuracy is assessed by computing the overlap of segmented edges. Precision and convergence properties are studied by comparing deformation fields. The results show that the Robbins-Monro method is the best choice in most applications. With this approach, the computation time per iteration can be lowered approximately 500 times without affecting the rate of convergence by using a small subset of the image, randomly selected in every iteration, to compute the derivative of the mutual information. From the other methods the quasi-Newton and the nonlinear conjugate gradient method achieve a slightly higher precision, at the price of larger computation times.     

Fully Solution‐Processed Photonic Structures from Inorganic/Organic Molecular Hybrid Materials and Commodity Polymers

Managing the interference effects from thin (multi‐)layers allows for the control of the optical transmittance/reflectance of widely used and technologically significant structures such as antireflection coatings (ARCs) and distributed Bragg reflectors (DBRs). These rely on the destructive/constructive interference between incident, reflected, and transmitted radiation. While known for over a century and having been extremely well investigated, the emergence of printable and large‐area electronics brings a new emphasis: the development of materials capable of transferring well‐established ideas to a solution‐based production. Here, demonstrated is the solution‐fabrication of ARCs and DBRs utilizing alternating layers of commodity plastics and recently developed organic/inorganic hybrid materials comprised of poly(vinyl alcohol) (PVAl), cross‐linked with titanium oxide hydrates. Dip‐coated ARCs exhibit an 88% reduction in reflectance across the visible compared to uncoated glass, and fully solution‐coated DBRs provide a reflection of >99% across a 100 nm spectral band in the visible region. Detailed comparisons with transfermatrix methods (TMM) highlight their excellent optical quality including extremely low optical losses. Beneficially, when exposed to elevated temperatures, the hybrid material can display a notable, reproducible, and irreversible change in refractive index and film thickness while maintaining excellent optical performance allowing postdeposition tuning, e.g., for thermo‐responsive applications, including security features and product‐storage environment monitoring.