Understanding the binder chemistry,microstructure, and physical properties of volcanic ash phosphate geopolymer binder

This work aims to assess the influence of the chemical composition of the binder resulting from the reaction of phosphoric acid and volcanic ash on its final characteristics. Six initial compositions of volcanic ash phosphate geopolymer with molar ratios Fe/P of 0.27, 0.5, 0.54, 0.81, 1, and 1.5 were designed by adding various dosages of phosphoric acid to volcanic ash. The results show that the hardening time increases with the decrease of molar ratios Fe/P. An excess of phosphoric acid leads to an unstable binder that is partially destroyed with the aging of the binder. The volcanic ash phosphate geopolymer with molar ratios of Fe/P = 0.5–0.54 has the optimum compressive strength (49–53 MPa at 90 days), the lowest water absorption (8.8-9.5 wt.%) as well as porosity (18–19.6 vol.%). The main binder is a porous phase of ferro-silico-aluminophosphate. Secondary phases were also identified in some mixes including ferro-aluminophosphate and magnesium phosphate.     

Aerosol Process for the In Situ Coating of Nanoparticles with a Polymer Shell

This article presents a novel method to encapsulate gas-borne nanoparticles with a polymeric shell. This method implies heterogeneous condensation of monomer vapor around the surface of nanoparticles as nuclei and polymerization is then subsequently started by addition of NH₃ as aerosol initiator. Ag and SiO₂ nanoparticles were generated as inorganic core by spark discharge and nebulization, respectively, and glycidyl methacrylate (GMA) was used as organic monomer. The effect of several parameters, including vapor pressure of monomer and properties of inorganic core such as morphology, material, particle size, and production method on the thickness of polymeric shell and morphology of resulting nanocomposites has been investigated. The particle size distribution and morphology of the resulting core-shell nanoparticles have been studied via scanning mobility particle sizer (SMPS) and transmission electron microscope (TEM). Finally, the coating efficiency was determined by aerosol photoemission (APE) and the results show that monomer and polymer coating efficiency are 99% and 60%, respectively.

Copyright 2014 American Association for Aerosol Research     

A monolithically integrated high‐efficiency Cu(In,Ga)Se2 mini‐module structured solely by laser

Monolithically integrated Cu(In,Ga)Se₂ mini‐modules were fabricated in order to reduce the width of patterning related dead area. The Cu(In,Ga)Se₂ layers were prepared on soda‐lime glasses using the multistage process at low substrate temperature below 500 °C. A picosecond laser with a wavelength of 532 nm was used for all of the structuring processes (P1, P2, and P3) for the monolithic integration. A “lift‐off” type structuring was applied for P1 and P3, and an “ablation” type was for P2. The laser structuring was optimized to be minimizing the dead area width, and the width of about 70 µm was successfully achieved. A mini‐module, in which the optimized structuring processes were applied for the integration, demonstrated a certified efficiency of 16.6%. Copyright © 2015 John Wiley & Sons, Ltd.     

Investigation of the Sharkskin melt instability using optical Fourier analysis

An optical method allowing the characterization of melt flow instabilities typically occurring during an extrusion process of polymers and polymer compounds is presented. It is based on a camera-acquired image of the extruded compound with a reference length scale. Application of image processing and transformation of the calibrated image to the frequency domain yields the magnitude spectrum of the instability. The effectiveness of the before mentioned approach is shown on Styrene-butadiene rubber (SBR) compounds, covering a wide range of silica filler content, extruded through a Göttfert capillary rheometer. The results of the image-based analysis are compared with the results from the sharkskin option, a series of highly sensitive pressure transducers installed inside the rheometer. A simplified version of the code used to produce the optical analysis results is included as supplementary material. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48806.     

Biosynthetic Plasticity Enables Production of Fluorinated Aurachins

Enzyme promiscuity has important implications in the field of biocatalysis. In some cases, structural analogues of simple metabolic building blocks can be processed through entire pathways to give natural product derivatives that are not readily accessible by chemical means. In this study, we explored the plasticity of the aurachin biosynthesis pathway with regard to using fluoro- and chloroanthranilic acids, which are not abundant in the bacterial producers of these quinolone antibiotics. The incorporation rates of the tested precursor molecules disclosed a regiopreference for halogen substitution as well as steric limitations of enzymatic substrate tolerance. Three previously undescribed fluorinated aurachin derivatives were produced in preparative amounts by fermentation and structurally characterized. Furthermore, their antibacterial activities were evaluated in comparison to their natural congener aurachin D.     

Topotaxial Formation of Mg4Nb2O9 and MgNb2O6 Thin Films on MgO (001) Single Crystals by Vapor–Solid Reaction

Thin-film solid-state reactions in the system MgO–Nb₂O₅ are experimentally investigated. MgO (001) substrates are subjected to Nb-O vapor at different temperatures in high vacuum. Thin films containing the phases Mg₄Nb₂O₉ and MgNb₂O₆ are formed by a vapor–solid reaction between the Nb-O vapor and the substrate. The crystallographic orientations of these phases are studied by X-ray diffractometry including pole figure analysis. Mg₄Nb₂O₉ grows (11.4)-, (11.6)-, and (11.9)-oriented, whereas MgNb₂O₆ grows with a preferential (241) orientation. The crystallographic relationships and their origins are discussed.     

Transition and flow boiling heat transfer inside a horizontal tube

Experiments on transition and flow boiling heat transfer with refrigerant R114 inside a horizontal tube were performed at bubble flow, critical heat flux and in the transition region between bubble flow and film boiling at mass fluxes between 1200 and 4000 kg/m² s and in the pressure range between 5 and 15 bar. In comparison with pool boiling bubble flow heat transfer depends essentially on the mass flow rates and on the vapor quality. The critical heat flux depends less on the temperature difference than in pool boiling heat transfer and exhibits a maximal and a minimal value as a function of the pressure. The critical heat flux increases with mass flow rate as already shown by Collier. In the region of transition boiling the heat flux over the difference between wall and saturation temperature approaches a horizontal curve. Therefore in this region an evaporator may always be operated under stable conditions and burn out does not occur.     

Sub-zero cooling: A novel strategy for high performance cutting

In this paper, a novel cooling strategy for high performance cutting is presented. A metalworking fluid, composed of water and polyhydric alcohols is applied at temperatures below 0 °C, but above the temperatures used for cryogenic cutting. This cooling strategy is applied when rough turning Ti-6Al-4V. An analysis of temperatures, forces, tool wear and chip formation is carried out. The results are compared with those obtained using emulsion, CO₂, LN₂, and dry turning. It can be shown that when tempering the sub-zero metalworking fluid down to ?30° C, tool temperatures as well as tool wear are reduced, and favourable chips are produced.     

Synthesis and electrochemical properties of Li[Li0.07Ni0.1Co0.6Mn0.23]O2 as a possible cathode material for lithium-ion batteries

The layered Li[Li_0.07Ni_0.1Co_0.6Mn_0.23]O₂ materials were synthesized by sol-gel method with glycine or citric acid as chelating agent. The prepared materials were characterized by means of XRD, SEM and Raman spectroscopy. Li/Li[Li_0.07Ni_0.1Co_0.6Mn_0.23]O₂ cells were assembled and subjected to charge-discharge studies at different C rates, viz 0.2, 1, 2 and 4 C. Although the samples showed less discharge capacity at 4 C rate the fade in capacity per cycle is lesser than that of capacity fade at 0.2 C rate. The citric acid assisted sample is found to be superior in terms of discharge capacity, capacity retention rate and also in thermal stability to that of sample prepared with glycine as chelating agent.     

Health assessment of artisanal gold miners in Indonesia

Small scale miners use mercury to extract gold from ore in many countries. An environmental and health assessment was performed in Indonesia in two regions, Galangan in Central Kalimantan and Talawaan in Northern Sulawesi. The environmental assessment showed severe mercury contamination of the sediments, and increased mercury levels in local fish. For the health investigation 281 volunteers were recruited and examined by a standardized questionnaire, a neurological examination and neuro-psychological tests. A medical score was used consisting of significant factors of mercury intoxication. Mercury exposed workers showed typical symptoms of mercury intoxication, such as movement disorders (ataxia, tremor, dysdiadochokinesia, etc.). Blood, urine and hair samples were taken from any participant and analyzed for mercury. The mercury concentration in the biomonitors was high, partly extreme high in the working population, increased in the population living in the same habitat and low in the control group. By a standard protocol which includes a combination of threshold values of mercury in the biomonitors and a medical sum score the diagnosis of chronic mercury intoxication was made for highly burdened workers (amalgam smelters) in 55% in Sulawesi and in 62% in Kalimantan. Less exposed mineral processors and the general population in the mining areas were also intoxicated to a high percentage.