Electrospun microporous gelatin–polycaprolactone blend tubular scaffold as a potential vascular biomaterial

The work reported involved the fabrication of an electrospun tubular conduit of a gelatin and polycaprolactone (PCL) blend as an adventitia‐equivalent construct. Gelatin was included as the matrix for increased biocompatibility with the addition of PCL for durability. This is contrary to most of the literature available for biomaterials based on blends of gelatin and PCL where PCL is the major matrix. The work includes the assiduous selection of key electrospinning parameters to obtain smooth bead‐free fibres with a narrow distribution of pore size and fibre diameter. Few reports elucidate the optimization of all electrospinning parameters to fabricate tubular conduits with a focus on obtaining homogeneous pores and fibres. This stepwise investigation would be unique for the fabrication of gelatin–PCL electrospun tubular constructs. The fabricated microfibrous gelatin–PCL constructs had pores of size ca 50–100 μm reportedly conducive for cell infiltration. The measured value of surface roughness of 57.99 ± 17.4 nm is reported to be favourable for protein adhesion and cell adhesion. The elastic modulus was observed to be similar to that of the tunica adventitia of the native artery. Preliminary in vitro and in vivo biocompatibility tests suggest safe applicability as a biomaterial. Minimal cytotoxicity was observed using MTT assay. Subcutaneous implantation of the scaffold demonstrated acute inflammation which decreased by day 15. The findings of this study could enable the fabrication of smooth bead‐free microfibrous gelatin–PCL tubular construct as viable biomaterial which can be included in a bilayer or a trilayer scaffold for vascular tissue engineering. © 2019 Society of Chemical Industry     

Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

The impacts of cattle access points on deposited sediment levels in headwater streams in Ireland

Cattle access to streams has been linked globally with degradation of stream water quality, driven largely by bank erosion and resultant instream, fine sediment deposition. The majority of evidence on such effects is however based in arid and semiarid regions of the United States and Australia, with few studies relating to cool temperate climates such as Northwest Europe. In this study, “Quorer” resuspendable sediment samples were taken from riffle geomorphic units upstream (control) and at two points downstream (pressure and recovery) of cattle access points in headwater streams in agricultural catchments in Ireland to assess levels of deposited stream sediment. Samples were taken in April/May (2016) prior to the grazing season and in October (2016) at the end of the grazing season. Sites in good‐high ecological status catchments and less than good ecological status catchments were included in the study. Higher levels of sediment were found downstream of cattle access points in both good‐high status and less than good status catchments; however, the impacts of access points were spatially confined to, in most cases, the area immediately downstream of the point of access. There was a strong correlation between deposited sediment mass and organic matter (OM) mass, with levels of OM increasing linearly with deposited sediment mass. Levels of measured sediment were negatively correlated with riparian habitat health (measured using a qualitative habitat assessment). The results of this study highlight the need for measures to prevent cattle access to headwater streams where access points can be many in order to manage local habitat quality and downstream water quality issues.     

Stabilization of 6H-Hexagonal SrMnO3 Polymorph by Al2O3 insertion

We demonstrate the structural evolution of polymorphic phases in Al₂O₃-inserted SrMnO₃ ceramics synthesized by solid state reaction. While the 4H-hexagonal phase is predominant in pure SrMnO₃ ceramics, a small amount of 6H-hexagonal polymorph is identified in addition to the primary 4H-hexagonal SrMnO₃ and the secondary hexagonal SrAl₂O₄ phases in the as-sintered ceramics, evidenced by x-ray diffraction and subsequent Rietveld refinement analyses. The existence of the 6H-hexagonal SrMnO₃ phase is corroborated using Raman spectroscopy. The chemical compositions and electronic structures of the Al₂O₃-inserted SrMnO₃ compounds are also examined using energy dispersive spectroscopy and x-ray photoelectron spectroscopy, respectively. The first-principles calculations reveal that there is no clear difference between the total energies of 4H- and 6H-hexagonal polymorphs regardless of the presence/absence of Sr and oxygen vacancies. Possible origins are discussed with the estimation of actual strain based on the refined lattice parameter of 6H SrMnO₃.     

Selective Coating of SnS on the Bio‐Inspired Moth‐Eye Patterned PEDOT:PSS Polymer Films

A new strategy for the selective coating of tin sulfide (SnS) on the surface of moth‐eye patterned (MEP) conducting polymer film is studied by considering the optical properties of the antireflective moth‐eye pattern and flexibility of polymer films. The semiconductor SnS is selectively coated on the surface of MEP microdomes of poly(3,4‐ethylenedioxythiophene) poly(styrene‐sulfonate) (PEDOT:PSS) film. The SnS coated MEP film is obtained by using pore selectively SnS thin layer functionalized polystyrene honeycomb‐patterned porous (HCP) film as a template. Aqueous PEDOT:PSS solution is poured on the SnS functionalized HCP films and detached for the fabrication of SnS coated MEP films. The films show a satisfactory photo‐responsive property under solar stimulated light illumination due to the antireflective MEP structure of PEDOT film and homogenous SnS coating on the surface of the conducting polymer.