Cu—Zn—Al系合金热弹性马氏体相变的热滞

本文通过热处理工艺及添加第四组元研究了Cu－Zn－Al系记忆合金的相变热滞。结果表明，淬火冷却速度影响合金的相变热滞大小，随着母相时效时间的延长，马氏体相变热滞变大．Mn元素的加入可以减小CU－Zn－Al合金相变热滞．     

3D optical interconnects for high-speed interchip and interboardcommunications

Metal-based communications between subsystems and chips has become the limiting factor in high-speed computing. Maturing optics-based technologies offer advantages that may unplug this bottleneck. Optical interconnects offer high-speed computers key advantages over metal interconnects. These include (1) high spatial and temporal bandwidths, (2) high-speed transmission, (3) low crosstalk independent of data rates, and (4) high interconnect densities. Although faster device switching speeds will eventually be necessary for future massively parallel computing systems, the deciding factor in determining system performance and cost will be subsystem communications rather than device speed. Free-space optical interconnects, by virtue of their inherent parallelism, high data bandwidth, small size and power requirement, and relative freedom from mutual interference of signals, already show great promise in replacing metal interconnects to solve communication problems     

Model development for multicomponent mass transfer with rapid chemical reactions in a small drop

Multicomponent mass transfer accompanied by instantaneous chemical reactions in a small drop has been modeled and simulated for the case where two different solutes diffuse from a continuous phase into the drop and react rapidly with a third reactant in the drop. The computational results obtained by Galerkin’s finite element method are reported in terms of concentration profiles, the locations of reaction front, the cumulative mass flux, and the enhancement factor. The effects of physical parameters, such as diffusivities of the solutes and the reactant, the interfacial concentration of solutes, and the relative amount of the reactant, on the calculated quantities are discussed.     

失水山梨醇倍半油酸酯的合成

考察了合成乳化剂失水山梨醇倍半油酸酯（ＡｒｌａｃｅｌＣ）的原料配比、反应温度、反应时间、催化剂用量对产品性能的影响，并找到了最佳反应条件．     

屏蔽暂堵反排解堵效率的实验分析

在一定实验条件下，屏蔽暂堵的反排解堵效率随压差、温度的增大而增大，反排解堵在很短的时间内就可完成。一般的反排解堵率都在60％以上，但反徘不能完全解堵。     

Matrix unit cell scheduler (MUCS) for input-buffered ATM switches

This paper presents a novel matrix unit cell scheduler (MUCS) for input-buffered asynchronous transfer mode (ATM) switches. The MUCS concept originates from a heuristic strategy that leads to an optimal solution for cell scheduling. Numerical analysis indicates that input-buffered ATM switches scheduled by MUCS can utilize nearly 100% of the available link bandwidth. A transistor-level MUCS circuit has been designed and verified using HSPICE. The circuit features a regular structure, minimal interconnects, and a low transistor count. HSPICE simulation indicates that using 2-μm CMOS technology, the MUCS circuit can operate at clock frequency of 100 MHz     

石英玻璃结构调整和二阶非线性光学效应产生机制的理论研究

从非谐振动理论观点出发．考虑到玻璃在外场及加热条件下结构取向调整和弛豫，对外部静电场和加热的温度及加热时间对其信频光产生的影响进行了探讨性理论研究，结果较好地解释了有关实验现象。     

System reliability estimation using simulation combined with network reductions

This paper proposes a dynamic Monte Carlo sampling method, called the conditional minimal cut set (COMICS) algorithm, where all arcs are not simulated at each trial and all minimal cut sets need not be given in advance. The proposed algorithm repeats simulating a minimal cut set composed of the arcs which originate from the (new) source node and reducing the network on the basis of the states of simulated arcs until the s-t connectedness is confirmed. We develop the importance sampling estimator, the total hazard estimator and the hazard importance sampling estimator which are all based on the proposed algorithm, and compare the performance of these simulation estimators. It is found that these estimators can significantly reduce the variance of the raw simulation estimator and the usual importance sampling estimator.     

粉末材料中微夹杂缺陷的超声波检验

介绍了用超声波方法检测微夹杂缺陷的一些试验结果，比较了不同频率、不同试验方法检测能力的差异，并通过解剖试验对检出缺陷的性质、尺寸作了比较。