Application of differential quadrature to static analysis of structural components

The numerical technique of differential quadrature for the solution of linear and non-linear partial differential equations, first introduced by Bellman and his associates, is applied to the equations governing the deflection and buckling behaviour of one- and two-dimensional structural components. Separate transformations are used for higher-order derivatives, as suggested by Mingle, thus extending the method to treat fourth-order equations and to include multiple, boundary conditions in the respective co-ordinate directions. Results are obtained for various boundary and loading conditions and are compared with existing exact and numerical solutions by other methods. The application of differential quadrature to this class of problems is seen to lead to accurate results with relatively small computational effort.     

运输包装件振动特性的计算机仿真

应用有限元法对计算机主机在运输过程中的振动特性进行了计算机仿真。首先利用Pro/E建立几何模型，然后基于ANSYS进行有限元动力分析，求出了包装件的固有频率与固有振型，以及频域／时域的动态响应。     

北京谱仪端盖簇射计数器工作气体的研究

为使北京谱仪端盖族射计数器更好地工作在自猝灭流光ＳＱＳ模式下，提高其能量分辨以及线性等指标，用Ａｒ，ＣＯ２，Ｌｓｏｂｕｔａｎｅ三元工作气体对探测器的工作性能进行了仔细研究，找出了一适合于主雇地数器的工作气体，此外，还研究了异丁的纯度对探测器性能的影响。     

Effect of bulk flow pulsations on film cooling with compound angle holes

Experiments are conducted to investigate the effects of bulk flow pulsations on film cooling with compound angle holes. A row of five film cooling holes is considered with orientation angles of 0°, 30°, 60°, and 90° at a fixed inclination angle of 35°. Static pressure pulsations are produced by an array of six rotating shutter blades, which extend across the span of the exit of the wind tunnel test section. The pulsation frequency is fixed at 36 Hz, but changes in the time-averaged blowing ratios of 0.5, 1.0 and 2.0 produce three different coolant Strouhal numbers, 3.6, 1.8 and 0.9, respectively. Detailed film cooled boundary layer temperature distributions are measured by a cold wire and the adiabatic film cooling effectiveness by thermochromic liquid crystal (TLC). The boundary layer temperature surveys show that pulsations induce large disruptions to the boundary layer temperature distribution and the film coverage. As the orientation angle increases, the injectant concentration spreads further into the spanwise direction because of pulsations than the steady case. With pulsations the adiabatic film cooling effectiveness value decreases regardless of the orientation angle. The amount of reduction, however, depends on the orientation angle in such a way that the larger the orientation angle is, the smaller the reduction is.     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

Development of a thermal hydraulic analysis code for gas-cooled reactors with annular fuels

Gas-cooled reactors have been highlighted as a promising option for next generation reactor technology. A thermal hydraulic analysis code for gas-cooled reactors has been developed with a heat transfer model of a block element, which is solved implicitly with the helium energy equation. Validation was carried out through comparison with both experimental and analytical results. A computation module for annular fuel rods has been coupled to the code for comparative analyses of an annular fuel-based block element. At normal operation, the annular fuel shows 80 °C lower peak temperature than the solid fuel for the same power in Japan's high temperature engineering test reactor (HTTR), even though the pressure drop is higher in the annular fuel.     

回火处理对高碳冷拔钢丝强度和塑性的影响

研究了６５钢冷拔钢丝在５００℃不同时间回火时的抗拉强度和延伸率的变化。试验结果发现，在回火初期，抗拉强度首先增长，然后随口火时间的延长连续降低，而延伸率始终在增长，增长速度是先快后慢。这种行为可归因于第一内应力的消除和ε－碳化物在形变铁素体中的析出以及后来再结晶的发生。     

Integration of mobile vehicles for automated material handlingusing Profibus and IEEE 802.11 networks

This paper focuses on a method to integrate mobile devices such as a mobile robot, automated guided vehicle, and unmanned container transporter to form an automated material handling system. In this paper, the stationary devices are connected via a Profibus network while the mobile devices are communicating via an IEEE 802.11 wireless LAN. In order to integrate these two networks, a protocol converter is developed on a PC platform that runs two interacting processes with shared internal buffers. The protocol converter performs a role of translator between two different protocols by converting the format of a data frame. In addition to this basic conversion function, the protocol converter has a virtual polling algorithm to reduce the uncertainty involved in accessing the wireless network. Finally, the integrated network. of Profibus and IEEE 802.11 is experimentally evaluated for its data latency and throughput, which shows the feasibility of the Profibus-IEEE 802.11 network for industrial applications involving mobile devices     

高频地波雷达相位补偿系统

OSMAR2000采用的是“一发八收,收发共用”模式的相控阵高频地波雷达.为了扩大其探测的范围,在新的雷达系统中将采用多发多收的模式,从而导致当信号通过通道后,信号的相位会因受到通道的调制而发生改变,使得雷达无法正常工作,因此需要对通道的相位进行实时监控和补偿.在参考了低频段的相位测量原理和射频段的相移电路的设计理论的基础上,该文提出了基于差分放大器、容阻和容感器件的高频地波雷达收发通道的相位控制系统.     

Ubiquitous Information Services with JAIN Platform

To provide responsive information services in a ubiquitous computing environment, service software and system development are indispensable. A component-based ubiquitous information system with a JAIN (Java APIs for Integrated Networks) platform to achieve seamless transmissions and reach-everywhere communications was designed in our research. In this development, numerous ubiquitous service modules were identified: location management, roaming, mobile IP and WAP networking. These component-based network modules were constructed using a component composition language with component specification and interface definition, running on top of a distributed service architecture using a JAIN platform to distribute the ubiquitous information services to mobile users. Two applications, Wireless-Application-Protocol (WAP) Mail and Video-on-Demand (VoD) services, show that the JAIN-like platform with the developed networking components effectively fills the gap for application developers between mobile appliances and various kinds of ubiquitous information services.