Development of geometrically exact new shell elements based on general curvilinear co‐ordinates

In the present study first‐order shear deformable shell finite elements based on general curvilinear co‐ordinates are proposed. For the development of the present shell elements, a partial mixed variational functional with independently assumed strains is provided in order to avoid the severe locking troubles known as transverse shear and membrane lockings. Bubble functions are included in the shape function of displacement to improve the performance of the developed element. The proposed assumed strain four‐ and nine‐node elements based on the general tensor shell theory provide an efficient linkage framework for shell surface modelling and finite element analysis. In the several benchmark problems, the present shell elements with exact geometric representations demonstrate their performance compared to previously reported results. Copyright © 2002 John Wiley & Sons, Ltd.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Fast locking delay-locked loop using initial delay measurement

A delay-locked loop (DLL) architecture capable of incorporating fast locking and low jitter features simultaneously is reported. A test chip was fabricated in a 0.6 μm CMOS process to prove its functionality. The proposed DLL can align the internal clock to the external reference clock within two cycles and maintain its locking state with the aid of feedback operation     

Development of a recurrent Sigma-Pi neural network rainfall forecasting system in Hong Kong

At the moment, weather forecasting is still an art — the experience and intuition of forecasters play a significant role in determining the quality of forecasting. This paper describes the development of a new approach to rainfall forecasting using neural networks. It deals with the extraction of information from radar images and an evaluation of past rain gauge records to provide shortterm rainfall forecasting. All of the meteorological data were provided by the Royal Observatory of Hong Kong (ROHK). Preprocessing procedures were essential for this neural network rainfall forecasting. The forecast of the rainfall was performed every half an hour so that a storm warning signal can be delivered to the public in advance. The network architecture is based on a recurrent Sigma-Pi network. The results are very promising, and this neural-based rainfall forecasting system is capable of providing a rain storm warning signal to the Hong Kong public one hour ahead.     

Wave-oriented signal processing of dispersive time-domainscattering data

Phase-space data processing is receiving increased attention because or its potential for furnishing new discriminants relating to classification and identification of targets and other scattering environments. Primary emphasis has been on time-frequency processing because of its impact on transient, especially wideband, short-pulse excitations. Here, we investigate the windowed Fourier transform, the wavelet transform, and model based superresolution algorithms within the context of a fully quantified and calibrated test problem investigated by us previously: two-dimensional (2-D) short-pulse plane wave scattering by a finite periodic array of perfectly conducting coplanar flat strips. Because the forward problem has been fully calibrated and parametrized, some quantitative measures can be assigned with respect to the tradeoffs of these time-frequency algorithms, yielding tentative performance assessments of the tested processing algorithms     

Hemodynamic response to in situ latissimus dorsi muscle stimulation: implications in dynamic cardiomyoplasty

Dynamic cardiomyoplasty (DCM) involves the electrical stimulation of a pedicled latissimus dorsi muscle flap wrapped around the falling ventricle as a means of cardiac assist. To further elucidate a potential neurohumoral mechanism for improvement of cardiac output after myoplasty, we evaluated the hemodynamic effects of in situ stimulation of the latissimus dorsi muscle (in the absence of cardiomyoplasty). In seven mongrel dogs, a nerve cuff electrode (Medtronic 6901) was placed around the left thoracodorsal nerve (TDN). This was attached to a pulse generator (Medtronic, Itrel 7420), delivering a 4.0 volt, 0.19 second on, 0.81 second off, 33 Hz, 210 microsecond pulse width, cyclic bursts similar to that used in DCM. Stroke volume index (SVI) and other hemodynamic parameters as well as plasma norepinephrine (NE) levels were measured at five stages: baseline, stimulator on at 0, 2, and 5 minutes, and stimulator off at 30 minutes after. The animals were then subjected to 4 weeks of rapid pacing at 240 beats/min (Medtronic 8329) to induce heart failure, and as the rapid pacing was discontinued, measurements were repeated as above. After rapid pacing, cardiac function was significantly depressed, and NE was elevated (133 +/- 69 versus 500 +/- 353 pg/mL, p < 0.05). In the normal hearts, TDN stimulation increased SVI, heart rate, systemic pressure, and NE levels. In heart failure, however, no significant changes in cardiac function and NE levels were noted. In conclusion, our data indicate that in the normal hearts, afferent impulses from TDN stimulation alone may augment cardiac function by means of a neurohumoral effect that is not seen in severe heart failure. The implications of these findings in DCM are discussed.     

A study of CaCO3 fouling with a microscopic imaging technique

The present study introduces a new experimental method to visualize the fouling process of CaCO₃. A mini-channel heat exchanger system with a microscopic imaging technique was developed for real-time visualization of the fouling process. The present study discussed how scale started initially, how scale formed thick layers, and how a small crystal grew into a large one, touching the adjacent one. Detail microscopic images of scale crystals and corresponding fouling resistances were obtained over the entire fouling process. The microscopic observation indicated that the fouling process could be divided into three stages: an induction period, a period of uniform generation of nuclei, and a period of uniform growth of scale. Sudden appearance of numerous small nuclei indicated the end of the induction period, a key event before the rapid increase in the fouling resistance. The present experimental method using microscopic images of the wet fouling process provides a valuable insight on the fouling mechanism.     

Evaluation of Monkman-Grant parameters for type 316LN and modified 9Cr-Mo stainless steels

The Monkman-Grant (M-G) and its modified parameters were evaluated for type 316LN and modified 9Cr-Mo stainless steels prepared with minor element variations. Several sets of creep data for the two alloy systems were obtained by constant-load creep tests in 550-650°C temperature range. The M-G parameters,m, m’,C, andC’ were proposed and discussed for the two alloy systems. Them value of the M-G relation was 0.90 in type 316LN steel and 0.84 in modified 9Cr-Mo steel. Them’, value of the modified relation was 0.94 in type 316LN steel and 0.89 in 9Cr-Mo steel. Although creep fracture modes and creep properties between type 316LN and modified 9Cr-Mo steels showed a basic difference, the M-G and its modified relations demonstrated linearity quite well. Them’ of modified relation almost overlapped regardless of the creep testing conditions and chemical variations in the two alloy systems, and the parameterm’ was closer to unity than that of the M-G relation.     

Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.