Effect of adsorptive gaseous reactant on non-isothermal behavior for gas-solid reactions

The effect of adsorptive species on non-isothermal gas-solid reactions is studied on the basis of Langmuir-Hinshelwood kinetics. The concept of an effectiveness factor provides good information to ascertain the effect of adsorptive species and the transition of the rate controlling regime, in connection with the parameters, generally used in the analysis of non-isothermal behavior. For highly exothermic reactions, the effectiveness factor-Thiele modulus curves with multiple solutions are presented with respect to the modified adsorption equilibrium constant. The variations of the rate-controlling regime by the effect of adsorptive species are also discussed.     

Enhanced utilization bound of Rate-Monotonic scheduling in Controller Area Networks

When priorities to message streams are assigned using Rate Monotonic (RM) for a Controller Area Network (CAN), the utilization bound is known to be about 25% for CAN 2.0A and 29% for CAN 2.0B. In this letter, we present a higher utilization bound than the existing ones with a reasonable constraint. The new utilization bounds are approximately 34% for CAN 2.0A and 41% for CAN 2.0B if no single message stream's utilization exceeds 46% or 27% of the total utilization for CAN 2.0A or CAN 2.0B, respectively.     

Semi-annual cycle of sea-surface temperature in the East/Japan Sea and cooling process

Semi-annual cycles of the sea-surface temperature (SST) in the East/Japan Sea (EJS) and their forcings were examined by analysing National Oceanic and Atmospheric Administration/Advanced Very-High-Resolution Radiometer data, scatterometer wind vectors, and heat flux data. The semi-annual cycle contributed to the total variance of the SST by 8% and amounted to 25% of the amplitudes of the annual SST cycle, particularly in the Tatarskiy Strait and along the continental shelf off Russia. The lowest phase, corresponding to the minimum SST, occurred during early November and 6 months earlier in May or June depending on the position. The forcings of the semi-annual cycle were not semi-annual but substantially annual with a lag of 6 months, which gave rise to SST cooling in spring and autumn. Our analyses illustrated that SST cooling in autumn was caused by direct, local atmospheric wind forcings, whereas the cooling with large amplitudes of the semi-annual cycle in spring was caused by the non-local, remotely forced cold water advection of the Liman Current associated with sea-ice melting in the Tatarskiy Strait. The phase lag of 1–2 months between the complete melting of the sea ice in the Tatarskiy Strait and the surface cooling along the Russian continental shelf was related to the advection of cold water from sea ice in the form of the Liman Cold Current. The semi-annual cycle also resulted from asymmetry of the time series of the SST due to a long cold winter and a short warm summer. To understand how SST curves are distorted and asymmetric, we suggested two mathematical parameters of kurtosis and skewness. In addition, we suggest that the ratio of the semi-annual amplitude to the annual amplitude of SST harmonics can be used as a typical indicator of the asymmetry in year-to-year SST variations.     

The use of non–physical standards in colour communication and matching

As a result of developments in spectrophotometry, together with improved accuracy in computer colour matching and laboratory dyeing, non–physical standards (reflectance data) can now be used for the successful communication, matching and quality control of colour. In colour palette generation, ‘matching by numbers’ has become a reality.     

Influence of Substrate Type on Level Dyeing of Acrylic Yarn Packages

In an earlier paper [1], the influence of flow rate, ramp (constant rate of temperature rise) and package density on the rates of dyeing of two basic dyes on Ex/an, and on the levelness obtained in the resulting dyeings, was investigated, and a relationship was derived to link these factors quantitatively. This work has now been extended to cover the behaviour of various basic dyes on Exlan and other acrylic fibres, under conditions expected to give borderline levelness. It has been shown that the shape of the rate–of–dyeing curve depends on the type of acrylic fibre and, to a lesser extent, on the cationic retarder used, but not on dye type within the group of CV2. 5–3. 5 basic dyes examined. The response of dyeing rate and degree of unlevelness to deliberate variations of ramp, as demonstrated in the previous work on Exlan, is now confirmed on Cashmilon. Evidence of a different type of random unlevelness, not related directly to dyeing rate, was also obtained from dyeings on the various fibres at a slow ramp.     

Microstructural Evidence for Diffusion-Driven Tetragonal-to-Orthorhombic Phase Transformation in Y-Ba-Cu-O Superconductor

Microstructures of Y-Ba-Cu-O superconductor were observed using a polarized microscope. Orthorhombic and tetragonal phases were easily distinguished by the optical etching with cross-polarized light. In the specimen cooled rapidly in oxygen, it was possible to see the path of oxygen diffusion by observing the variation of the twin concentration. At the boundary between transformed and untransformed materials, evidence for diffusion-driven transformation could be clearly seen.     

Adsorption and desorption characteristics of 2-methyl-4-chlorophenoxyacetic acid onto activated carbon

Adsorption and desorption characteristics of the 2-methyl-4-chlorophenoxyacetic acid (MCPA) from aqueous solution onto the activated carbon (GAC, F-400) were studied. Adsorption equilibrium capacities of the MCPA increased with decreasing pH and temperature of the solution. Adsorption equilibrium of the MCPA could be represented by the Sips equation. The internal diffusion coefficients were determined by comparing the experimental concentration decay curves with those predicted from surface diffusion model and pore diffusion model. The adsorption model based on the linear driving force approximation (LDFA) was used for simulating the adsorption behavior of the MCPA in a fixed bed. Over ninety five percent desorption of the MCPA could be obtained using distilled water.     

Monodisperse polymer/metal composite particles by electroless chemical deposition: Effect of surface functionality of polymer particles

Micron‐sized polymer particles were coated with layers of nickel compounds by plating electrolessly in the presence of aqueous solutions of nickel chloride, sodium hypophosphite, sodium citrate, and ammonium chloride at elevated temperature. The uniform functional polymer particle could be obtained by seeded polymerization. To investigate the effect of surface functionality on the conditions for nickel deposition, the polymer particle was functionalized with the thiol group. From morphological observation, it was found that the mode of nickel deposition was greatly dependent on the surface functionality of the polymer particle. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 420–424, 2003     

Preparation of nano-sized silicon carbide powder using thermal plasma

Nano-sized silicon carbide (SiC) powder was prepared by thermal plasma process using silicon tetrachloride (SiCl₄) and methane (CH₄). The synthesized powder was characterized by X-ray diffraction pattern, scanning electron microscopy, transmission electron microscopy, FT-IR spectroscopy and particle size analyzer. The powder was dominated by β-SiC including some of α-SiC and free carbon species. The quality of the powder was varied with process conditions such as the molar ratio of H/Si and C/Si, and collecting positions. It was known that the conversion to SiC was mainly affected by the addition of hydrogen gas because it promoted the decomposition and reduction of SiCL. CH₄ was easily decomposed to carbon species for the formation of SiC as well as removal of impure oxygen, but excessive carbon suppressed the formation of crystalline SiC and resulted in the solid carbon contamination. The optimum ratio of H/Si was approx. 26 and that of C/Si was 1.1. For collecting positions, the powder collected at the vessel and filter was preferable to that at the reaction tube. The average size of the powder synthesized was estimated to be below 100 nm and uniform in distribution.     

AMMONIA CATALYZED ORGANOSOLV DELIGNIFICATION OF POPLAR

A parametric investigation of NH₄OH catalyzed solvent delignification of poplar was conducted to define pretreatment conditions which would yield an optimal separation of the biomass components and an enzymatic susceptible solid carbohydrate phase. Delignification parameters of interest included concentration of NH₄OH, time and temperature of the reaction, and type of solvent. The addition of 0.82 M NH₄OH to the delignification liquor increased lignin removal and decreased carbohydrate degradation, but increasing NH₄OH concentration had no additional effect. At lower reaction temperatures, the extent of delignification increased with reaction time; at higher temperatures, a “relignification” of the pretreated wood was observed. The delignification and hemicellulose solubilization were modelled and rate constants reported. No major difference between three potential pulping solvents—ethanol, butanol, phenol—was observed. The enzymatic susceptibility of pretreated wood samples was approximately 6-fold greater than that of the untreated poplar. UV absorbance was used to qualitatively characterize the soiubilized lignins.