Fabrication of micro heaters on polycrystalline 3C-SiC suspended membranes for gas sensors and their characteristics

This paper describes the design, fabrication, and characteristics of micro heaters mad on AlN (0.1 μm)/3C-SiC (1 μm) suspended membranes using surface micromachining technology. 3C-SiC and AlN thin films, which have a large energy band gap and very low lattice mismatch, were used for high-temperature environments. A Pt thin film was used as micro heaters and temperature sensor materials. The resistance of the temperature detector (RTD) and the power consumption of the micro heater were measured and calculated. The heater is designed for an operating temperature up to about 800 °C and can be operated at about 500 °C with a power of 312 mW. The thermal coefficient of the resistance (TCR) of fabricated Pt RTD’s is 3174.64 ppm/°C. The thermal distribution measured by IR thermovision is uniform across the membrane surface.     

Experimental demonstration of enhancing pump absorption rate in cladding-pumped ytterbium-doped fiber lasers using pump-coupling long-period fiber gratings

A long-period fiber grating (LPFG) was inscribed in a single-mode fiber and was spliced with a ytterbium (Yb)-doped double-clad fiber in order to couple pump radiation of the inner cladding into the core in a cladding-pumped fiber laser. The use of an LPFG permits a partial core-pumping scheme in a cladding-pumping fiber laser because a portion of the pump radiation can be coupled to the core by LPFG. The enhancement of the pump absorption of a Yb-doped cladding-pumped fiber laser as the result of pump coupling by LPFG was 35%, and the maximal output power increased by up to 55% when a 20-W pump source is used.     

A 20-GHz phase-locked loop for 40-gb/s serializing transmitter in 0.13-/spl mu/m CMOS

A 20-GHz phase-locked loop with 4.9 ps/sub pp//0.65 ps/sub rms/ jitter and -113.5 dBc/Hz phase noise at 10-MHz offset is presented. A half-duty sampled-feedforward loop filter that simply replaces the resistor with a switch and an inverter suppresses the reference spur down to -44.0 dBc. A design iteration procedure is outlined that minimizes the phase noise of a negative-g/sub m/ oscillator with a coupled microstrip resonator. Static frequency dividers made of pulsed latches operate faster than those made of flip-flops and achieve near 2:1 frequency range. The phase-locked loop fabricated in a 0.13-/spl mu/m CMOS operates from 17.6 to 19.4GHz and dissipates 480mW.     

High average power, high repetition rate, picosecond pulsed fiber master oscillator power amplifier source seeded by a gain-switched laser diode at 1060 nm

We demonstrate a pulsed ytterbium-doped fiber master-oscillator power amplifier source at 1060 nm producing over 300 W of average power in 20-ps pulses at 1-GHz repetition rate. The pulses generated by a gain-switched diode were compressed by a chirped fiber Bragg grating and amplified without any distortion with excellent spectral quality. This fiber master oscillator power amplifier system offers versatility and potential for further power scaling.     

Computation sharing programmable FIR filter for low-power and high-performance applications

This paper presents a programmable digital finite-impulse response (FIR) filter for high-performance and low-power applications. The architecture is based on a computation sharing multiplier (CSHM) which specifically targets computation re-use in vector-scalar products and can be effectively used in the low-complexity programmable FIR filter design. Efficient circuit-level techniques, namely a new carry-select adder and conditional capture flip-flop (CCFF), are also used to further improve power and performance. A 10-tap programmable FIR filter was implemented and fabricated in CMOS 0.25-/spl mu/m technology based on the proposed architectural and circuit-level techniques. The chip's core contains approximately 130 K transistors and occupies 9.93 mm/sup 2/ area.     

A 980-nm Yb-doped fiber MOPA source and its frequency doubling

A continuous-wave (CW) master oscillator-power amplifier (MOPA) fiber source, tunable around 978 nm, was frequency-doubled to 488.7 nm. Both the laser and the amplifier were made with cladding-pumped jacketed air-clad Yb-doped fibers. The MOPA generated up to 2.7 W of power in an output beam with an M/sup 2/ value of 1.8. This was frequency-doubled in a periodically poled potassium titanyl phosphate crystal at room temperature, in a single-pass configuration. The generated blue light had a CW power of 18.1 mW, a nearly Gaussian spatial intensity profile, and an M/sup 2/ value of 1.7.     

Variable length signal detection framework for cognitive radio systems

The cognitive radio (CR) system opportunistically utilizes the frequency bands temporally unoccupied by the primary user. In the CR system, the energy or cyclostationary detector is used to detect the primary user signal. For protecting the primary user tightly, the signal detection time can be very long, which leads to inefficiency in the CR system. Thus, we propose a novel signal detector that greatly reduces the average detection time. The proposed detector periodically decides whether it terminates the detection process or receives more input signal for more information. Therefore, the proposed detector has variable detection time. We will call the proposed detector the variable length signal detector (VLSD). The VLSD is designed by using a partially observable Markov decision process framework for optimal performance. We present the numerical results showing that the VLSD requires much smaller average detection time compared with the traditional fixed length signal detector to achieve a given detection error probability. Copyright © 2012 John Wiley & Sons, Ltd.     

Compact Circularly Polarized Antenna with a Capacitive Feed for GPS/GLONASS Applications

This letter presents a novel compact circularly polarized patch antenna for Global Positioning System/Global Navigation Satellite System (GPS/GLONASS) applications. The proposed antenna is composed of a simple square radiating patch fed by a capacitive dual‐feeder to increase the impedance bandwidth and a lumped element hybrid coupler to achieve the broadband characteristic of the axial ratio (AR). The realized antenna dimensions are 28 mm × 28 mm × 4 mm, which is the most compact size among the dual‐band GPS/GLONASS antennas reported to date. The measured results demonstrate that the proposed antenna has a gain of 2.5 dBi to 4.2 dBi and an AR of 0.41 dB to 1.51 dB over the GPS/GLONASS L1 band (1.575 GHz to 1.61 GHz).     

An SSD‐Based Storage System for an Interactive Media Server Using Video Frame Grouping

For real‐time interactive multimedia operations, such as video uploading, video play, fast‐forward, and fast‐rewind, solid state disk (SSD)‐based storage systems for video streaming servers are becoming more important. Random access rates in storage systems increase significantly with the number of users; it is thus difficult to simultaneously serve many users with HDD‐based storage systems, which have low random access performance. Because there is no mechanical operation in NAND flash‐based SSDs, they outperform HDDs in terms of flexible random access operation. In addition, due to the multichannel architecture of SSDs, they perform similarly to HDDs in terms of sequential access. In this paper, we propose a new SSD‐based storage system for interactive media servers. Based on the proposed method, it is possible to maximize the channel utilization of the SSD's multichannel architecture. Accordingly, we can improve the performance of SSD‐based storage systems for interactive media operations.